Life Cycle Analysis of Methanol Production via Photocatalytic Carbon Conversion
LCA modeling approach, scenario analysis, and key results of methanol production via photocatalytic carbon conversion.
White, John↗
Engineering topics
White, John
Publications and source records attributed to White, John.
Hydrogen Shot Technology Assessment: Thermal Conversion Approaches
In July 2021 the United States (U.S.) Department of Energy (DOE) launched the first of a series of Department-wide Energy Earthshot™ goals designed to accelerate breakthroughs of more abundant, affordable, and reliable clean energy solutions within the decade. The Hydrogen Shot goal seeks to reduce the cost of clean hydrogen to $\$$1 per 1 kilogram in 1 decade ("1 1 1"). Today, thermal conversion of fossil fuels represents the predominant, lowest cost method of hydrogen production. In 2020 approximately 75 percent of global, dedicated hydrogen production was produced via fossil fuels using thermal conversion approaches such as steam reforming and gasification. However, carbon management techniques such as CO 2 capture and sequestration (CCS) and pyrolysis are not widely represented in the current fossil-based hydrogen production fleet. Lowering the cost of clean hydrogen production from commercial and advanced thermal conversion-based technologies is critical for successfully achieving the Hydrogen Shot goal. This report presents the findings from an initial screening analysis of several scenarios that explore cost drivers related to clean hydrogen production. The screening encompasses commercially available and developing thermal conversion technology alternatives as well as factors exogenous to the plant such as feedstock/byproduct pricing, CO 2 pipeline and storage infrastructure costs, and scale to assess potential pathways towards meeting the Hydrogen Shot goal. Additionally, this report presents initial Research and Development (R&D) strategies to advance thermal conversion technology towards meeting the Hydrogen Shot™ goal.
08 HYDROGEN↗
Strategies for Achieving the DOE Hydrogen Shot: Thermal Conversion Approaches
This poster summarizes a screening-level analysis performed by NETL's Strategic Systems Analysis and Engineering (SSAE) Directorate in support of achieving DOE's Hydrogen Shot Goal. Included are objectives, results, and primary conclusion of the analysis.
McNaul, Shannon↗
Life Cycle Analysis of Synthetic Natural Gas Production via Carbon Conversion: Impact of Different CO2, H2, and Methanation Pathways
Life Cycle Analysis of Synthetic Natural Gas Production via Carbon Conversion: Impact of Different CO2, H2, and Methanation Pathways
Henriksen, Megan↗
Tool for Insertion of a Fiber-Optic Terminus in a Connector
A tool has been developed for the special purpose of inserting the terminus of an optical fiber in a cable connector that conforms to NASA Specification SSQ- 21635. What prompted the development of the tool was the observation that because of some aspects of the designs of fiber-optic termini and of springs, sealing rings, and a grommet inside the shell of such a connector, there is a tendency for the grommet to become damaged and detached from the sealing rings during installation. It is necessary to ensure the integrity of the grommet for proper sealing and proper functioning of the connector. The special-purpose tool provides the needed protection for the grommet. The grommet-protection tool resembles a funnel into which an axial slit has been cut (see figure). Prior to insertion, the grommet-protection tool is rolled so that one side of the slit overlaps the other side. The rolled-up grommet-protection tool is inserted in one of the connector holes that accommodate the fiber-optic termini and is pushed in until the flange (the wider of the two conical portions) of the tool becomes seated on the connector grommet. Then a special-purpose installation tool is inserted in the flange of the grommet-protection tool and pressed in until it becomes seated in the flange. This operation expands the narrower of the two conical portions of the grommet-protection tool. The installation tool is removed and the grommet-protection tool remains expanded due to the flat surfaces on the axial slit. By use of a standard contact-insertion tool, a fiber-optic terminus is inserted, through the grommet-protection tool, into the connector cavity. By use of a pair of forceps or needle-nose pliers, the grommet-protection tool is then pulled out of the cavity. Finally, the grommet-protection tool is removed from around the installed fiber-optic cable by pulling the cable through the axial slit. Unlike in some prior procedures for installing the fiber-optic termini in the connector, the procedure that involves the use of the present grommet-protection tool does not include the use of lubricants that can contaminate the interior of the connector. The grommet-protection tool is made of a fluoropolymer, taking advantage of the flexibility of such polymers and further taking advantage of the inherent slipperiness of fluoropolymers. Although the tool is designed primarily for insertion of a fiber-optic terminus, it might also be useful for extracting a previously installed fiber-optic terminus.
King, Wes↗