Engineering Papers⌕ Search

Engineering topics

Weinstein, L. M.

Publications and source records attributed to Weinstein, L. M..

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

Hybrid suction surface for turbulent boundary layer flow

A hybrid suction surface which combines favorable aspects of both uniformly porous and discrete opening suction surfaces has been evaluated experimentally for use with incompressible turbulent boundary layers. The surface consisted of an array of closely spaced slots aligned in the direction of the freestream flow. Direct drag and mean boundary layer velocity profile measurements showed that the slotted surface had nominally the same suction characteristics as a uniformly porous surface.

Wilkinson, S. P.↗
NASA NTRS1978

Drag and heat transfer on surfaces with small longitudinal fins

An investigation is conducted regarding the drag characteristics of longitudinally ribbed surfaces using various configurations which attempt to confine the turbulent wall bursts to regions of small transverse extent in the initial birth region. The ratio of heat transfer increase to drag increase for the high area ratio rib configurations is determined and the heat transfer efficiency of the present surfaces is compared with data found in the literature. The drag data obtained indicate local 'wetted area skin friction' reductions but due to the increased surface area the planform drag is increased in most instances. There is no indication of drag reduction with the rectangular ribbed models that had sharp leading and fin tip edges. Heat transfer data indicate that several of the triangular grooved models have efficiencies approximately 10 percent higher than that of a smooth flat plate.

Walsh, M. J.↗
NASA NTRS1977

Compliant wall surface motion and its effect on the structure of a turbulent boundary layer

The status of the continuing compliant wall drag reduction research at NASA-Langley Research Center is discussed. Preliminary surface motion calculations are reported along with compliant surface design concepts and their numerical models. A compliant drag reduction theory based on stabilizing the turbulent substructure is proposed and previous experiments have been examined relative to that theory. Results of recent low speed compliant surface experiments have been reported which include initial attempts to measure local compliant surface motion.

Ash, R. L.↗
NASA NTRS1977

An electrostatically driven surface for flexible wall drag reduction studies

This paper describes the theoretical analysis, experimental development and surface motion data from an electrostatically driven flexible wall capable of producing high frequency, large amplitude, short wavelength standing wave motions. The driven wall was developed for use in studying flexible wall-turbulent boundary layer interactions. The theoretical analysis considers the coupled electrochemical system using a continuum model. For the system under consideration the electrical field is uncoupled from the mechanical system leading to a simplified analysis. The structural problem is a non-linear (moderately) large amplitude problem and details of the analysis are presented. Surface motion measurements, made using a modified schlieren type optical system, are discussed and details of the surface motion under different excitations are presented. Fair agreement is obtained between experimental measurements and theoretical calculations.

Weinstein, L. M.↗
NASA NTRS1976

Re-examination of compliant wall experiments in air with water substrates

A possible alternative explanation is proposed for compliant wall drag reductions measured in previous investigations. Standing waves were observed to form on the surfaces of compliant wall models in air with water substrates as the freestream velocity was increased from 15 to 30 m/s. These waves resembled sine waves with half of the wave protruding over the upstream portion of the model and the other half being recessed over the downstream end of the model. These data coupled with results of recent drag reduction experiments suggest that standing waves could have caused a shift in the model center of gravity creating a bending moment that was interpreted as a reduction in the skin friction drag.

Hefner, J. N.↗
NASA NTRS1975

Experimental verification of turbulent skin friction reduction with compliant walls

Preliminary compliant wall skin friction test results obtained in a low-turbulence pressure tunnel are reported. Compliant surface skins consisted of 0.0025 cm thick mylar, stretched under tension and area-bonded or longitudinally strip-bonded with silicone rubber adhesive to polyurethane foam. Mean velocity and fluctuating survey data were obtained with a single slanted hot wire. Mean velocity profiles for the area-bonded mylar surface skins indicated up to a 20% reduction in boundary-layer thickness (and lower momentum thickness) over rigid surfaces. This reduction in boundary-layer thickness indicates that a drag reduction occurred. In addition, a 16% reduction in wall shear was evident for the mylar/compressor foam compliant surface.

Weinstein, L. M.↗
NASA NTRS1975

Compliant wall-turbulent skin-friction reduction research

Previous compliant-wall experiments successful in reducing skin-friction drag probably have had a (unplanned) membrane resonance at a favorable frequency, amplitude, wave shape, length, and speed. The most probable drag reduction mechanism involves a direct coupling between the fluid and the moving wall when the wall natural resonance frequencies are near the fundamental turbulent burst frequency. Local skin-friction reductions of 61% were measured with mylar/PVC plastisol compliant surfaces. These reductions were observed only at certain flow conditions, indicating that changing tunnel total temperature may have altered the substrate dynamic modulus, damping, and coupled mylar tension. Apparently, the coupled membrane/substrate must be excited in compatible narrow-band natural frequency modes. An accelerated effort is required to develop practical durable compliant surfaces optimized for maximum drag reduction. Application of compliant walls to other transportation modes appears feasible with liquid flows offering the greatest skin-friction drag reduction potential.

Fischer, M. C.↗
NASA NTRS1974

Hot-wire anemometry in hypersonic helium flow

Hot-wire anemometry techniques are described that have been developed and used for hypersonic-helium-flow studies. The short run time available dictated certain innovations in applying conventional hot-wire techniques. Some examples are given to show the application of the techniques used. Modifications to conventional equipment are described, including probe modifications and probe heating controls.

Wagner, R. D.↗
NASA NTRS1973

Hot-wire coil probe for high-speed flows

Small-diameter-wire coil probes developed for use in a hypersonic helium tunnel are discussed. The springlike properties of the coil minimize strain-gauge effects, and allow to use a higher length-to-diameter ratio for a given flow. In addition, the coil is more rugged for sudden flow changes, and since it can be mounted straight across the support tips, there is less support interference in cross flows. In addition to measuring fluctuating quantities in a boundary layer, the probes were used with a constant temperature anemometer for measuring mean mass flow profiles, and with a constant current anemometer for measuring mean total temperature profiles.

Weinstein, L. M.↗
NASA NTRS1973

Improved photographic prints with a linear radial transmission filter

Linear Radial Transmission Filter (LRTF) is easy to use and yet results in prints which depict more information contained in negative than can be shown by direct printing. LRTF is optical-quality filter which has maximum transmission in center and linear drop in transmission radially out from center.

Weinstein, L. M.↗
NASA NTRS1973

Three-dimensional hypersonic transitional/turbulent mean flow profiles.

Detailed three-dimensional compressible transitional/turbulent boundary-layer profiles are presented for use as test cases in numerical and integral calculation procedures. The profiles were obtained from tests conducted in the Mach 20 leg of the Langley High Reynolds Number Helium Facility. The presented data represent an arduous test case for analytical prediction methods, since 'low Reynolds number' and precursor transition effects should probably be accounted for to accurately predict the boundary-layer growth and development.

Fischer, M. C.↗
NASA NTRS1972

Oblique shock-sound interaction at a freestream Mach number of about 20 in helium.

Detailed experimental measurements of the characteristics and level of pre- and postshock disturbances obtained for typical disturbance modes and shock angles are presented to aid in the evaluation of transition studies conducted in 'noisy' hypersonic wind tunnels. The presented data suggest that the shock is probably generating total temperature fluctuations in a fashion directly related to shock strength. Since in high supersonic and hypersonic flows the total temperature fluctuations are mainly contained in velocity fluctuations, it may be concluded that the predominant disturbances generated are vorticity as long as the postshock flow is at a sufficiently high Mach number.-

Weinstein, L. M.↗
NASA NTRS1972

Cone transitional boundary-layer structure at Me = 14.

Experimental results suggest that the boundary-layer mean profiles in hypersonic flows may be highly transitional in the outer part of the boundary layer before the transition process is detected at the surface. Means of determining the initial location where the transition process begins in the outer part of the boundary layer are considered.

Fischer, M. C.↗