Engineering topics

Wedeven, L. D.

Publications and source records attributed to Wedeven, L. D..

At least 19 records

NASA NTRS1996

Enhancement of Perfluoropolyether Boundary Lubrication Performance

A ball bearing simulator operating under starved conditions was used to perform screening tests to evaluate the boundary lubrication performance of a branched perfluoropolyether (PFPE), K-143 AB. Several approaches to enhance boundary lubrication were studied. These included: (1) soluble boundary additives, (2) bearing surface modifications, (3) 'run-in' surface films, and (4) ceramic bearing components. In addition, results were compared with two non-perfluorinated liquid lubricant formulations. Based on these tests, the following tentative conclusions can be made: (1) Substantial improvements in boundary lubrication performance were observed with a beta-diketone boundary additive and a tricresyl phosphate (TCP) liquid surface pretreatment, (2) the use of rough Si3N4 balls (R(sub a) = 40 micro-inch) also provided increases in test duration, but with concomitant abrasive wear, (3) moderate improvements were seen with two boundary additives (a phosphine and a phosphatriazine) and a neat (100%) fluid (a carboxylic acid terminated PFPE); and small improvements with surface pretreatments with synthetic hydrocarbons, a polytetrafluoroethylene (PTFE) coating, and TiC coated 440 C and smooth Si3N4 balls (R(sub a) = 1 micro-inch), and (4) two non-PFPE lubricant formulations (a polyalphaolefin (PAO) and synthetic hydrocarbon) yielded substantial improvements.

Jones, W. R., Jr.↗

NASA NTRS1995

Enhancement of perfluoropolyether boundary lubrication performance: I. Preliminary results

A ball bearing simulator operating under starved conditions was used to evaluate the boundary lubrication performance of a perfluoropolyether (PFPE) Krytox 143 AB. Several approaches to enhance boundary lubrication were studied. These included: (1) soluble boundary additives, (2) bearing surface modifications, (3) 'run-in' surface films, and (4) ceramic bearing components. In addition, results were compared with two non-perfluorinated liquid lubricant formulations. Based on these preliminary tests, the following tentative conclusions can be made: (1) substantial improvements in boundary lubrication performance were observed with a beta-diketone boundary additive and a tricresyl phosphate (TCP) liquid surface pretreatment; (2) the use of rough Si3N4 balls (Ra = 40 micro-in) also provided substantial improvement but with concomitant abrasive wear; (3) marginal improvements were seen with two boundary additives (a phosphine and a phosphatriazine) and a neat (100%) fluid (a carboxylic acid terminated PFPE); and surface pretreatments with a synthetic hydrocarbon, a PTFE coating, and TiC coated 440C and smooth Si3N4 balls (R(sub a) less than 1 micro-in); and (4) two non-PFPE lubricant formulations (a PAO and a synthetic hydrocarbon) yielded substantial improvements.

Jones, W. R., Jr.↗

NASA NTRS1991

Material and tribological considerations for turbopump bearings

The frictional heat generation in the rolling/sliding contact areas of high pressure oxygen turbopump (HPOTP) bearings is a key factor in bearing life. Several bulk materials, surface treatments and coatings are examined for their attributes of rolling contact fatigue life, wear and friction. Emphasis is given to the frictional response of these materials under conditions of rolling with incipient sliding as predicted from HPOTP bearing analysis. Rolling contact fatigue life is shown to be significantly improved with silicon nitride. Fatigue life can also be improved by coating the chromium carbide-laden stainless steels (440C, BG42) with TiN and thin dense chrome. The traction (friction under rolling/sliding) of these materials is discussed in terms of microslip and the presence of interfacial films.

Wedeven, L. D.↗

NASA NTRS1990

New Materials And Treatments For Turbopump Bearings

Report evaluates materials and surface treatments for bearings for liquid-oxygen turbopumps. Key properties sought for application are low friction, low wear, and resistance to corrosion and rolling-contact fatigue.

Wedeven, L. D.↗

NASA NTRS1986

Solid lubrication design methodology, phase 2

The high temperature performance of solid lubricated rolling elements was conducted with a specially designed traction (friction) test apparatus. Graphite lubricants containing three additives (silver, phosphate glass, and zinc orthophosphate) were evaluated from room temperature to 540 C. Two hard coats were also evaluated. The evaluation of these lubricants, using a burnishing method of application, shows a reasonable transfer of lubricant and wear protection for short duration testing except in the 200 C temperature range. The graphite lubricants containing silver and zinc orthophosphate additives were more effective than the phosphate glass material over the test conditions examined. Traction coefficients ranged from a low of 0.07 to a high of 0.6. By curve fitting the traction data, empirical equations for slope and maximum traction coefficient as a function of contact pressure (P), rolling speed (U), and temperature (T) can be developed for each lubricant. A solid lubricant traction model was incorporated into an advanced bearing analysis code (SHABERTH). For comparison purposes, preliminary heat generation calculations were made for both oil and solid lubricated bearing operation. A preliminary analysis indicated a significantly higher heat generation for a solid lubricated ball bearing in a deep groove configuration. An analysis of a cylindrical roller bearing configuration showed a potential for a low friction solid lubricated bearing.

Pallini, R. A.↗

NASA NTRS1983

The influence of surface dents and grooves on traction in sliding EHD point contacts

Changes in traction, caused by dents and grooves on a highly polished ball, are investigated as these defects approach and go through sliding elastohydrodynamic point contacts. The contacts are formed with the ball loading against a transparent disk. The ball and thus the topographical features are held stationary at various locations in the vicinity and within the contact while the disk is rotating. These topographical features can cause substantial changes in the traction when compared to traction obtained with smooth surfaces. Previously announced in STAR as N82-32734

Cusano, C.↗

NASA NTRS1983

Elastohydrodynamic contacts. Effects of dents and grooves on traction and local film thickness

Traction and film thickness were simultaneously measured under sliding elastohydrodynamic (EHD) conditions. The influence of surface topography was investigated by using simulated surfaces produced by depressing dents and grooves in highly polished steel balls. Significant changes in traction occurred depending on the orientation of the surface defects and their location with respect to the contact region. The results can be explained in terms of changes in overall film thickness and redistribution of pressure within the contact region due to micro-EHD effects. It can be concluded that the traction capability of mechanical components operating in thin film lubrication can be enhanced particularly by surface topographical orientation perpendicular to the surface motion. Associated with the higher traction are increases in local shear stress and normal stress as well as an increase in temperature at asperity sites. It is postulated that the local surface topography can become involved in run in or failure initiation even without actual asperity contact.

Wedeven, L. D.↗

NASA NTRS1983

Assessment of lubricated contacts: Mechanisms of scuffing and scoring

Scoring and scuffing are defined as two distinct but related forms of failure of hardened ferrous components lubricated by liquids. Experimental observations of these phenomena are described, and criteria for scoring and scuffing are discussed. The mechanisms proposed by various authors to explain these observations are enumerated. The view presented here is that, under conditions yet to be defined, scoring is a gradual breakdown of the lubrication of interacting asperities, such lubrication being boundary or microelastohydrodynamic in nature, or a mixture of the two. The final scuffing stage represents a breakdown of the main elastohydrodynamic system, but this may be triggered by the deterioration in surface topography as a result of scoring. An extension of published theoretical treatment of elastohydrodynamic breakdown is proposed, and a critical experiment to assess the importance of edge effects in band contacts is suggested. The practical implications of the proposed mechanism are reviewed, and recommendations for further work are made. A possible thermal instability mechanism for the breakdown of boundary lubrication is outlined.

Dyson, A.↗

NASA NTRS1983

Surface topography-connections between lubrication and failure initiation

The characteristics of the initial surface topography is intimately connected to the machining process by which it is produced. Both processes create a near surface region of residual stresses, microstructure and hardness that is different from the bulk. The material properties in this rather undefined region can significantly influence the mode of failure, such as wear, scuffing or fatigue, as well as the degree of failure resistance for a given material. Under full film elastohydrodynamic (EHD) conditions, where shear is accomodated within a relatively thick lubricant film, the normal and shear stresses are distributed uniformly over the near surface region, and the surface topography has little influence on the lubrication or failure process. Under more typical conditions where surface roughness and lubricant film thickness are of the same order of magnitude, the surface topography not only emerges as an important parameter in failure initiation, but it also becomes intimately involved in the lubrication process itself.

Wedeven, L. D.↗

NASA NTRS1982

The influence of surface dents and grooves on traction in sliding EHD point contacts

Changes in traction, caused by dents and grooves on a highly polished ball,are investigated as these defects approach and go through sliding elastohydrodynamic point contacts. The contacts are formed with the ball loading against a transparent disk. The ball and thus the topographical features are held stationary at various locations in the vicinity and within the contact while the disk is rotating. These topographical features can cause substantial changes in the traction when compared to traction obtained with smooth surfaces.

Cusano, C.↗

NASA NTRS1981

The effects of artificially-produced defects on the film thickness distribution in sliding EHD point contacts

Effects of artificially produced dents and grooves on the elastohydrodynamic film thickness profile in a sliding point contact are investigated using optical interferometry. Defects on the surface of a highly polished ball are held stationary at various locations within the vicinity of the contact region while the disk is rotating. It is shown that defects can dramatically change the film thickness which exists when no defects are present in or near the contact, and it is shown that the change in thickness is mainly a function of the position of the defects in the inlet region, the geometry of the defects, the orientation of the defects in the case of grooves, and the depth of the defect relative to the central film thickness.

Cusano, C.↗

NASA NTRS1981

Effects of artificially produced defects on film thickness distribution in sliding EHD point contacts

The effects of artificially produced dents and grooves on the elastohydrodynamic (EHD) film thickness profile in a sliding point contact were investigated by means of optical interferometry. The defects, formed on the surface of a highly polished ball, were held stationary at various locations within and in the vicinity of the contact region while the disk was rotating. It is shown that the defects, having a geometry similar to what can be expected in practice, can dramatically change the film thickness which exists when no defects are present in or near the contact. This change in film thickness is mainly a function of the position of the defects in the inlet region, the geometry of the defects, the orientation of the defects in the case of grooves, and the depth of the defect relative to the central film thickness.

Cusano, C.↗

NASA NTRS1979

Elastohydrodynamic film thickness measurements of artificially-produced nonsmooth surfaces

Optical interferometry is used to measure the elastohydrodynamic (EHD) film thickness associated with artificially produced, nonsmooth surfaces. The nonsmooth surfaces are produced by modifying the surfaces of highly-polished balls with irregularities in the form of multiple grooves and dents. By closely spacing these irregularities, it is possible not only to produce depressions on the surface of the balls but also to generate pseudo asperities. The average roughness wavelength of this artificially-produced, nonsmooth surface approximates the average fundamental roughness wavelength found on surfaces of some mechanical elements operating under concentrated contact. By comparing the measured film thickness profiles to the stylus traces of the irregularities, it is possible to observe the local deformations associated with micro-EHD pressure generation. In both pure rolling and pure sliding conditions, the artificially-produced 'asperities' are deformed and complete separation exists between them and the mating surface. Such findings demonstrate the importance of local surface topography and resulting micro-EHD effects on the film thickness between rough surfaces in concentrated contact. In addition, sliding data are presented which demonstrate a severe constriction, caused by the irregularities, at the exit of the Hertzian region.

Cusano, C.↗

NASA NTRS1979

Diagnostics of wear in aeronautical systems

The use of appropriate diagnostic tools for aircraft oil wetted components is reviewed, noting that it can reduce direct operating costs through reduced unscheduled maintenance, particularly in helicopter engine and transmission systems where bearing failures are a significant cost factor. Engine and transmission wear modes are described, and diagnostic methods for oil and wet particle analysis, the spectrometric oil analysis program, chip detectors, ferrography, in-line oil monitor and radioactive isotope tagging are discussed, noting that they are effective over a limited range of particle sizes but compliment each other if used in parallel. Fine filtration can potentially increase time between overhauls, but reduces the effectiveness of conventional oil monitoring techniques so that alternative diagnostic techniques must be used. It is concluded that the development of a diagnostic system should be parallel and integral with the development of a mechanical system.

Wedeven, L. D.↗

NASA NTRS1979

Diagnostics of wear in aeronautical systems

Maintenance costs associated with the transmissions and drive train greatly increase the maintenance burden and failure risk. Detection measurements fall under two general categories of vibration and particle detectors. The latter are more amenable to tracking wear. Wear debris analysis can supply a great deal of information such as: particle concentration, rate of change in concentration, composition, particle size and shape, principal metals, etc. It is not economically feasible to monitor all variables. At least one role of the lubrication and wear specialist is to provide guidance in selecting the most appropriate variables to monitor.

Wedeven, L. D.↗

NASA NTRS1979

Elastohydrodynamic film thickness measurements of artificially produced nonsmooth surfaces

Optical interferometry is used to measure the elastohydrodynamic (EHD) film thickness associated with artificially produced nonsmooth surfaces. The nonsmooth surfaces are produced by modifying the surfaces of highly-polished balls with irregularities in the form of multiple grooves and dents. By closely spacing these irregularities it is possible not only to produce depressions on the surface of the balls but also to generate pseudo asperities. The average roughness wavelength of this artificially-produced, nonsmooth, surface approximates the average fundamental roughness wavelength found on surfaces of some mechanical elements operating under concentrated contact. By comparing the measured film thickness profiles to the stylus traces of the irregularities, it was possible to observe the local deformations associated with micro-EHD pressure generation. In both pure rolling and pure sliding conditions the artificially-produced asperities are deformed and complete separation exists between them and the mating surface. Such findings demonstrate the importance of local surface topography and resulting micro-EHD effects on the film thickness between rough surfaces in concentrated contact. Sliding data are presented which demonstrate a severe constriction, caused by the irregularities, at the exit of the Hertzian region.

Cusano, C.↗

NASA NTRS1978

Elastohydrodynamic film thickness measurements of artificially produced surface dents and grooves

Elastohydrodynamic (EHD) film thickness measurements using optical interferometry have been made of artificially produced dents and grooves under rolling and sliding conditions. These measurements are compared to stylus traces of the dent and groove profiles to determine the local deformation associated with micro-EHD pressure generation. The surface geometry associated with the dents and grooves is seen to become intimately involved in the lubrication process itself, creating local pressure variations that substantially deform the local surface geometry, particularly under sliding conditions. The rolling results have implications concerning surface initiated fatigue and the sliding results show clearly the EHD surface interactions that must occur prior to scuffing failure.

Wedeven, L. D.↗

NASA NTRS1978

Elastohydrodynamic film thickness measurements of artificially produced surface dents and grooves

Elastohydrodynamic (EHD) film thickness measurements using optical interferometry were made of artificially produced dents and grooves under rolling and sliding conditions. These measurements are compared to stylus traces of the dent and groove profiles to determine the local deformation associated with micro-EHD pressure generation. The surface geometry associated with the dents and grooves became intimately involved in the lubrication process itself, creating local pressure variations that substantially deformed the local surface geometry, particularly under sliding conditions. The rolling results implied surface initiated fatigue, and the sliding results showed clearly the EHD surface interactions that must occur prior to scuffing failure.

Wedeven, L. D.↗