Engineering Papers⌕ Search

Engineering topics

Wang, Yanli

Publications and source records attributed to Wang, Yanli.

At least 73 records · Page 4

Testing in Support of the Development of EPP Plus SMT Design Method at ORNL (FY2021)

Experiments in support of the development of the integrated Elastic–Perfectly Plastic (EPP) plus Simplified Model Test (SMT) design methodology, referred to as the EPP+SMT method, continued in FY21. This report focuses on the methodology for developing the EPP+SMT creep-fatigue (CF) design curves at low strain ranges. The creep damage-based method and dissipated work-based method were used to evaluate the available CF data at the low strain range region. A set of failure criteria were determined, and a simple extrapolation method was developed to predict the CF life cycles at low strain ranges that are not accessible by experiments due to the extraordinarily long failure times at the low strain region (thousands to hundreds of thousands of years) and the inability of the test machine to control these small strain ranges due to the signal to noise issues. An experimental method with the concept of block-strain range CF testing was proposed to generate the information needed to extrapolate the CF design curves to low strain ranges. Based on this new testing approach, a preliminary EPP+SMT CF design curve was developed for Alloy 617 at 950°C with tension hold time of 100 s. The analysis in this report shows the potential of generating a set of EPP+SMT CF design curves with different hold times within a reasonable amount of time and testing effort. Based on such a progress, a hold time extrapolation procedure for low strain ranges will be developed in FY22 and critical testing will be carried out to complete the development of the EPP+SMT CF design curves for Alloy 617.

36 MATERIALS SCIENCE↗

Creep, Fatigue, and Creep-Fatigue Testing of Alloy 709 Base Metal at ORNL (FY 2021)

The testing activities and research in support of ASME Code qualification of Alloy 709, an advanced austenitic steel, are being carried out at Oak Ridge National Laboratory (ORNL), Argonne National Laboratory, and Idaho National Laboratory. ORNL has been tasked to carry out a subset of the Code Case testing for creep rupture, fatigue and creep-fatigue. The focus of the FY 2021 Code Case testing on Alloy 709 base metal at ORNL includes (1) continuing the long-term creep rupture testing on ESR1100 and AOD1100; (2) adding ESR1150-AH to the creep Code Case testing matrix; and (3) continuing fatigue and creep-fatigue Code Case testing on ESR1150- AH. This report summarizes the status and the preliminary test results of FY 2021 planned Code Case testing at ORNL.

36 MATERIALS SCIENCE↗

Bifunctional nanoprecipitates strengthen and ductilize a medium-entropy alloy

Single-phase high- and medium-entropy alloys with face-centred cubic (fcc) structure can exhibit high tensile ductility and excellent toughness, but their room-temperature strengths are low. Dislocation obstacles such as grain boundaries, twin boundaries, solute atoms and precipitates can increase strength. However, with few exceptions, such obstacles tend to decrease ductility. Interestingly, precipitates can also hinder phase transformations. Here, using a model, precipitate-strengthened, Fe–Ni–Al–Ti medium-entropy alloy, we demonstrate a strategy that combines these dual functions in a single alloy. The nanoprecipitates in our alloy, in addition to providing conventional strengthening of the matrix, also modulate its transformation from fcc-austenite to body-centred cubic (bcc) martensite, constraining it to remain as metastable fcc after quenching through the transformation temperature. During subsequent tensile testing, the matrix progressively transforms to bcc-martensite, enabling substantial increases in strength, work hardening and ductility. This use of nanoprecipitates exploits synergies between precipitation strengthening and transformation-induced plasticity, resulting in simultaneous enhancement of tensile strength and uniform elongation. Further, our findings demonstrate how synergistic deformation mechanisms can be deliberately activated, exactly when needed, by altering precipitate characteristics (such as size, spacing, and so on), along with the chemical driving force for phase transformation, to optimize strength and ductility.

36 MATERIALS SCIENCE↗

Characteristics of Premature Creep Failure in Over-tempered Base Metal of Grade 91 Steel Weldment

Characteristics of premature creep failure in the over-tempered base metal (OT-BM) of a Grade 91 steel weldment are investigated with specially designed creep experiments and advanced microstructure characterization. In situ digital image correlation (DIC) strain measurements reveal that local creep strain as high as 100% accumulated in the OT-BM, compared with only 10% nominal strain over the gauge length. The creep strain rate in the OT-BM is identical to that in the intercritical heat-affected zone and fine-grained heat-affected zone at the secondary creep stage and early tertiary stage, but faster at the late tertiary stage. Microstructural analysis shows that highly recovered microstructure in the OT-BM leads to the lowest hardness, the largest grain size, the lowest fraction of coincidence site lattice boundaries, and the lowest localized strain energy. Dislocation creep and transgranular creep fracture are the dominant deformation and fracture mechanisms in the OT-BM under the current creep testing condition of a low temperature (550 °C) and a high stress (215 MPa).

42 ENGINEERING↗

Design rules for 316H nuclear components cladded with nickel or tungsten

The existing Class A metallic materials qualified in the ASME Boiler & Pressure Vessel Code Section III, Division 5 rules for high temperature nuclear reactors are not ideally suited for long term molten salt corrosion resistance in high temperature molten salt reactors. Potentially, corrosion or corrosion driven environmentally assisted cracking could limit the design life of structural components in molten salt reactors. A solution to this limitation is the use of cladded components – overlay the Class A material with a thin layer of some non-qualified, corrosion-resistant material. However, this necessitates the development of design methods for cladded components that do not require long-term testing of clad materials in order to support the near-term deployment of molten salt reactors. This report develops such a methodology along with a complete set of rules presented in a format compatible with an ASME nuclear Code Case. These design rules are for 316H Class A components cladded with either nickel or tungsten. The report also discusses the development of a set of general criteria for selecting clad materials beyond the specific 316H/tungsten and 316H/nickel systems and general acceptance tests for checking the mechanical integrity of the clad/base metal interface. Finally, the report includes a set of fully-documented sample problems detailing the application of the rules to high temperature cladded components

36 MATERIALS SCIENCE↗

An improved specimen preparation method for marine shallow gas-bearing sand sediments and its validations

Instabilities of shallow gas-charged seabed are potential geological hazards in ocean engineering. In practice, the conventional field sampling techniques failed to obtain undisturbed gas-bearing sediments from the seabed for laboratory mechanical testing because of sensitive gas exsolution and escape from sediments. However, preparation of representative remoulded gas-charged specimens is a challenging issue, because it is rather difficult to quantitatively control the gas content and obtain uniform distribution of gas bubbles within the specimen. Given the above problems, this work proposes a reliable approach to reconstitute the high-saturation specimen of gas-charged sediments in the laboratory by an improved multifunction integrated triaxial apparatus (MITA). This apparatus is developed based on an advanced stress path triaxial system by introducing a temperature-controlled system and a wave-monitoring system. The temperature-controlled system is used to accurately mimic the in situ environments of sediments in the seabed. The wave-monitoring system is utilized to identify exsolution point of free gas and examine the disturbance of gas to specimens during gas exsolution. The detailed procedure of gassy specimen preparation is introduced. Then, the quality of prepared specimens using our improved apparatus is validated by the high-resolution micro-X-ray computed tomography (μCT) scanning test, from which bubble occurrence and size distribution within the gassy sand specimen can be obtained; and preliminary mechanical tests on gassy sand specimens with various initial saturation degrees are performed. The proposed specimen preparation procedure succeeds in proving the postulated occurrence state of gas bubbles in coarse-grained sediments and accurately controlling the gas content.

58 GEOSCIENCES↗

Experimental evaluation of localized creep deformation in grade 91 steel weldments

Spatially resolved measurement of localized creep deformation in heterogeneous creep resistant steel weldments is crucial but challenging for lifetime assessments of critical steam components in power plants. Here, experimental approaches were established to quantitatively evaluate commonly observed localized creep deformation in multi-pass Grade 91 steel weldments. An in-situ digital image correlation (DIC) system was utilized with a creep testing frame to monitor and measure both full-field strain and localized strain accumulation across the weldments during long-term creep testing at elevated temperatures. The in situ DIC method measured not only the creep deformation behavior of the weld metal, heat affected zone (HAZ), and base metal, but also creep strain evolution for each sub-region within the HAZ itself, including coarse-grained HAZ, fine-grained HAZ (FGHAZ), and intercritical HAZ (ICHAZ). The DIC results revealed that local creep strain in the ICHAZ reached up to 90% strain before final rupture, whereas nominal creep strain measured by the standard extensometer of the tested cross-weld specimen was below 10%, indicative of Type IV cracking of the Grade 91 weld. Microstructural analyses revealed that the faster creep degradation/deformation in the HAZ was caused mainly by accelerated matrix grain recrystallization/growth and a reduced pinning effect from the segregated and coarsened precipitates in the FGHAZ and ICHAZ. The ultimate creep rupture occurred in the ICHAZ owing to its lowest creep resistance induced by the largest recrystallized grain size, the lowest fraction of coincidence site lattice, and the lowest local strain energies/dislocation densities.

36 MATERIALS SCIENCE↗

Fatigue Performance of High-Strength Pipeline Steels and Their Welds in Hydrogen Gas Service

Objectives of the project include: Enable the use of high strength steel hydrogen pipelines, as significant cost savings can result by implementing high strength steels as compared to lower strength pipes. Demonstrate that girth welds in high-strength steel pipe exhibit fatigue performance similar to lower-strength steels in high-pressure hydrogen gas. Identify pathways for developing high-strength pipeline steels by establishing the relationship between microstructure constituents and hydrogen-accelerated fatigue crack growth (HA-FCG)

08 HYDROGEN↗

Report on FY 2020 testing of Alloy 709 in support of EPP analysis

Research activities in support of the development of a 500,000 hr, 760ºC ASME Code Case (CC) for Alloy 709 are ongoing at Oak Ridge National Laboratory (ORNL), Argonne National Laboratory, and Idaho National Laboratory. Integration of the simplified Elastic-Perfectly Plastic (EPP) methods for the design of Alloy 709 reactor components is a requirement for the Alloy 709 CC. This report documents the research plans and initiation of testing in support of integrating EPP analysis methods for Alloy 709 at ORNL in FY 2020. Tests are designed and initiated to evaluate the effect of cyclic loading on the creep properties of Alloy 709. The preliminary results show that cyclic loading has an insignificant effect on the minimum creep rate, although additional tests are recommended to confirm this conclusion. A preliminary testing plan for multi-axial creep rupture has been established and the specimens are machined. Execution of the testing plan will continue in FY 2021.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Microstructure and Mechanical Properties of Intercritically Treated Grade 91 Steel

Premature creep failures at the intercritical heat affected zone (ICHAZ) of creep-resistant steel weldments have been frequently reported. However, the creep degradation mechanism of different microstructure constituents in ICHAZ is complicated and needs further clarification. In this work, Grade 91 steel was intercritically heat-treated at a temperature (860 °C) between the critical temperatures AC1 and AC3, and a correlation between microstructure and mechanical properties of the heat-treated specimen was built. The effects of austenitization and tempering resulting from the intercritical treatment (IT) differentiated the local strain energies between the two microstructure constituents: newly transformed martensite (NTM) and over-tempered martensite (OTM). The formation of NTM grains led to a hardness increase from 247 HV0.5 in the base metal to 332 HV0.5 in the IT specimen. The ultimate tensile strength (UTS) increased from 739 MPa in the base metal to 1054 MPa in the IT specimen. Extensive growth of the OTM grains and rapid recovery of NTM grains took place simultaneously in the IT specimen during a typical tempering at 760 °C. These microstructure degradations led to a lowered hardness of 178 HV0.5, a reduced UTS of 596 MPa, and a poor creep resistance with a minimum creep strain rate of 0.49 %/h at 650 °C in an IT + tempering (ITT) specimen.

36 MATERIALS SCIENCE↗

Report on FY 2020 creep, fatigue and creep fatigue testing of Alloy 709 base metal at ORNL

The testing activities and research in support of ASME Code qualification of Alloy 709, an advanced austenitic steel, are being carried out at Oak Ridge National Laboratory (ORNL), Argonne National Laboratory, and Idaho National Laboratory. This report summarizes the status and results of FY 2020 planned testing at ORNL. Uniaxial tensile tests on the electroslag remelt (ESR) solution-annealed plate (heat number 58776-3RBC) with additional heat treatment were performed for the baseline mechanical properties evaluation for ASME code qualification of Alloy 709. The tensile properties were found to meet ASME SA-213 specifications and were comparable to the Nippon Steel NF709 data generated for an ASME Section I Code Case for seamless tubing. ORNL was tasked to carry out a subset of the Code Case testing for creep rupture. Creep rupture data from 18 tests were generated on a solution-annealed ESR plate with a solution annealing temperature of 1100°C. There are total of 19 intermediate and long-term creep rupture tests of Alloy 709 ongoing at ORNL. A preliminary fatigue design curve at 760°C was developed for Alloy 709, and the results show that the fatigue design curve of Alloy 709 is comparable to that of Alloy 800H at 760°C.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Report on FY 2020 Welding Parameters Optimization and the Fabrication of Qualified Alloy 709 Welds

Alloy 709 is an attractive candidate construction material for the Sodium Fast Reactor (SFR). As part of the Alloy 709 Intermediate Term Test Program, this work covers the development of the technical basis for weld fabrication and weld qualification of Alloy 709. The phase of research reported herein focused on the issue of weld solidification cracking recently experienced in both experimental heats and a commercial heat of Alloy 709 with relatively high phosphorous levels.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Advanced Materials Program Summary

Materials solutions - enabling design, construction, and operation of licensable Advanced Nuclear Material, design, fabrication, installation, examination, testing, overpressure protection, inspection, stamping, and certification

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Report on FY 2020 Testing in Support of the Development and Extension of ASME Code Rules for Grade 91

This report summarizes the FY 2020 research and activities at Oak Ridge National Laboratory in support of the ASME code rule development and code extension for Grade 91 (Gr. 91) steel. Incorporation of the Gr. 91 temperature-dependent fatigue curves in Section III Division 5 was one major task, and the associated major aspects brought up during the course of the ASME balloting process are documented in this report. Experiments and analysis continued on the development of the alternative creep-fatigue evaluation based on elastic–perfectly plastic (EPP) plus simplified model test (SMT) methodology. The focus of the study in FY 2020 was the evaluation of the hold-time effect at high cycle and low strain range region. Baseline testing in support of the evaluation of hold time effects was started and will continue in FY 2021. Major on-going experiments and activities in support of the ASME code development and extension of Gr. 91 will be completed in FY 2021.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

Support of the Development of EPP Plus SMT Design Method (FY2020 Test Results)

Experiments in support of the development of the integrated Elastic–Perfectly Plastic (EPP) analysis and Simplified Model Test (SMT) design methodology continued in FY 2020. The previously developed single-bar SMT (SBSMT) technique was successfully extended to tubular shaped Alloy 617 specimens for evaluation of the effect of primary pressure load on SMT creep-fatigue (CF) properties at 950°C. A series of pressurized SMT tests were performed with various elastic follow-up factors and strain ranges. The results show that the primary pressure load reduces the SMT CF cycles. The reduction of SMT CF life due to primary load was found to be dependent on strain ranges, elastic follow up and test temperatures. These results are crucial for verification of the EPP strain range analysis in the EPP+SMT evaluation procedure. Additionally, hold time effect on the SMT CF life cycles is a determining factor for generating the EPP+SMT CF design curves. Lack of test data in the high cycle and low strain range region results in major uncertainty in developing the design curves. In FY2020, experiments were designed, and testing started on Alloy 617 at 950°C to fill the gap in experimental data. The on-going CF and additional SMT CF with elastic follow-up at low strain ranges will generate the information needed to verify the methods for extrapolation to long hold time and finalize the EPP+SMT design method.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗