Engineering Papers⌕ Search

Engineering topics

Wang, Yanli

Publications and source records attributed to Wang, Yanli.

At least 37 records · Page 2

A summary of the mechanical properties data developed in FY 2023 by ANL, INL and ORNL to support the data package development for the A709 Code Case

This report provides the status of tensile, creep, fatigue, and creep-fatigue testing to date conducted at Argonne National Laboratory, Idaho National Laboratory, and Oak Ridge National Laboratory to generate the data package required to qualify Alloy 709 in American Society of Mechanical Engineers, Boiler and Pressure Vessel Code, Section III, Division 5. The Division 5 Class A Alloy 709 Code Case requires data generated from a minimum of three commercial heats. Extensive mechanical properties data have been generated on two commercial heats, and some initial test data have been generated from the third commercial heat. The room temperature tensile test results for the three commercial heats met the specification minimum of the American Society of Mechanical Engineers, Boiler and Pressure Vessel Code, Section II, Part A, SA-213/SA-213M for Grade TP310MoCbN (UNS S31025) seamless tubing. These three commercial heats of Alloy 709 are suitable for generating the code case data.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

FY23 status report on the development of new ASME Section III, Division 5 Class B rules

This report summarizes the work done in Fiscal Year 2023 on the development of the new American Society of Mechanical Engineers Boiler and Pressure Vessel Code, Section III, Division 5, Class B rules to address the gaps identified for high temperature reactor designs. The summary of the design-by-analysis strain limit evaluation and creep-fatigue damage assessment is presented. The proposed design-by-analysis creep-fatigue damage calculation approach uses a new elastic follow-up-based Isochronous Stress Strain Curve stress relaxation procedure. This approach captures the elastic follow-up generated due to interactions of components with adjacent components, supports, and other connections in the power plant. A set of sample problems are selected to validate the proposed design-by-analysis rules for creep-fatigue damage assessment. The proposed Class B rules are evaluated against the Class A elastic design rules, and the experimental data obtained from a family of Simplified Model Test based key-feature test results. The proposed Class B creep-fatigue damage assessment methodology yields conservative design cycles estimates compared to the experimental results.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Report on FY 2023 Experimental Results in Developing the Fabrication Parameters for Alloy 709 in Different Product Forms

The Advanced Reactor Technologies (ART) Program has established a multi-year plan to develop Alloy 709 advanced stainless steel (A709), generate the data package and develop material-specific design parameters in qualifying it as a new structural material for Class A construction in the American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel Code, Section III, Division 5, High Temperature Reactors (ASME 2023). In collaboration with material vendors, the Advanced Materials Development activities under ART have successfully scaled the A709 plate form production from a laboratory heat of 500 pounds to commercial heats totaling 133,000 pounds of A709 plate fabricated from three heats. The goal of the overall A709 development program is to establish the necessary microstructural and mechanical properties relationship for A709 to ultimately develop fabrication parameters for other product forms such as bars, pipes, and forgings using the available ART A709 materials. The objective of this A709 development work in FY 2023 is to experimentally determine grain coarsening behavior for the A709 heats and to experimentally generate the continuous cooling precipitation (CCP) diagram for A709 using the as-rolled commercial heat plate materials. Integral to this work is the characterization of the as-rolled materials and the determination of an effective solution-annealing process, which was reported in Y. Wang et al., 2023. This report summarizes the results of the high-speed dilatometry project to develop the CCP diagram using the commercial heat 58776-3RB fabricated by G. O. Carlson and heat 529900-02 fabricated by Allegheny Technologies Incorporated (ATI) Specialty Rolled Products.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Design and Scoping Tests on Alloy 617 Using Notched Specimen Geometry to Validate Methods for Multiaxial Stress Relaxation

In FY 2022, a development effort was initiated at the US Department of Energy’s Oak Ridge National Laboratory (ORNL) to examine the multiaxial stress-relaxation behavior and multiaxial stress-state effect on the creep-fatigue (CF) performance for Alloy 617 at elevated temperatures. This effort supported the development of the design rules in the American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel Code (BPVC), Section III, Division 5. In this work, two types of the notch specimen geometries were designed. An inelastic constitutive model was used to investigate the stress triaxiality and elastic follow-up effects on the notch specimens under CF deformation in the finite element (FE) simulations. The numerical study demonstrated that the stress triaxiality and elastic follow-up caused by the notches both play significant roles in the stress-relaxation behavior. In addition, Alloy 617 CF experiments were designed, and the testing on the notch specimens is ongoing. CF test failure data will be generated on the specimens with notches under various conditions in FY 2023, and the results will be used to validate methods for accounting for the multiaxial stress relaxation effect in the design code.

36 MATERIALS SCIENCE↗

Report on FY 2023 Welding R&D at ORNL in support of ASME Alloy 709 Code Case Development

As part of the Alloy 709 (A709) ASME Code Case development effort under the Advanced Reactor Technologies (ART) Program, this work covers the development of the technical basis for weld fabrication and weld qualification of A709. This report summarizes the A709 welding research conducted at Oak Ridge National Laboratory (ORNL) in FY 2023. One of the focuses of the A709 welding research at ORNL is to relax the restriction of the P content in the A709 filler metal weld wire. In this report, we show the success in welding of high phosphorus (P) commercial A709 plates using A709 weld wires with relaxed P content of 80 wppm. A test weld was fabricated with the 80 wppm weld wire on the first commercial heat A709 base metal with 140 wppm P content using gas tungsten arc welding (GTAW). The test weld passed all weld qualification tests without issues. This study concludes that A709 matching filler metal with moderate amount of P of less than 80 wppm could be used to produce code qualified A709 welds with standard welding process without special treatment. It is recommended that the P level in the weld wire to be kept low to avoid hot cracking. Cross-weld specimens were machined from the two A709 production welds.. Cross welding creep rupture Code Case testing on these two production welds was initiated . The preliminary cross-weld creep tests results continue to show little or no creep strength reduction relative to the base metal.

36 MATERIALS SCIENCE↗

A Summary of the Microstructural Characterization Results for the A709 Commercial Heats

To improve high temperature strength for advanced nuclear reactors, it is necessary to qualify additional structural materials for introduction into the American Society of Mechanical Engineers (AMSE) Boiler and Pressure Vessel Code (BPVC). Specifically, Alloy 709 was identified as a material for Sodium-cooled Fast Reactors to enhance time-dependent mechanical properties compared to 316H stainless steel, a code qualified high temperature alloy. Idaho National Laboratory (INL) and Oak Ridge National Laboratory (ORNL) performed initial microstructure and mechanical property testing on a third, commercial heat of Alloy 709 stainless steel. The Alloy 709 plate was produced by Allegheny Technology Inc. (ATI) and in the solution annealed condition. The chemical composition was within the limits for an American Society of Testing and Materials (ASTM) A213 specification for seamless tube for material UNS S31025. Grain size was measured as an average ASTM size of 6.5, which was larger than the ASTM 7 required according to ASTM A213 for seamless tube. The chemical composition was within the limits for an ASTM A213, and the room temperature tensile tests and hardness data met ASTM A213 specifications. Creep-fatigue results showed similar behavior to previous heats of Alloy 709.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Report on FY 2023 Research and Development on Specially Designed Creep-fatigue Experiments on Alloy 617 in Support of Improving Creep-fatigue Evaluation Approaches

Experimental and numerical studies in support of developing the integrated Elastic–Perfectly Plastic (EPP) plus Simplified Model Test (SMT) design methodology, referred to as the EPP+SMT method, continued in FY 2023. This report focuses on the methods for extrapolating the EPP+SMT creep-fatigue life curves at long hold times and low strain ranges at elevated temperatures. In this work, the available uniaxial creep-fatigue failure data on Alloy 617 at temperatures of 950°C and 850°C were analyzed to provide a guidance on the development of the extrapolation method and the creep-fatigue failure criteria. A viscoplastic constitutive model for Alloy 617 was adopted to extrapolate the mechanical responses to low strain ranges and long hold times. A set of design curves of Alloy 617 at temperatures of 950°C, 850°C, and 800°C with tensile hold times of 1 hr, 100 hr, and 1,000 hr are developed. Furthermore, creep-fatigue testing on two notch specimen geometries, shallow-notch and sharp V-notch, on Alloy 617 was performed 950°C to understand the multiaxial stress relaxation behavior. The experimental and numerical results on the notch specimens were compared with those on the standard uniaxial smooth bar specimens. The effect of multi-axial stress state combined with elastic follow-up on the stress relaxation behavior was investigated in this report.

36 MATERIALS SCIENCE↗

NOTCH EFFECT ON CREEP-FATIGUE BEHAVIOR OF ALLOY 617 AT ELEVATED TEMPERATURE

High-temperature reactor structural components are often under the complex multiaxial creep-fatigue (CF) loading conditions throughout the lifetime because of geometric and/or metallurgical discontinuities and complex loading paths. To assess the multiaxial CF deformation behavior and to evaluate the CF design rules in the ASME BPVC Section III, Division 5, Subsection HB, Subpart B, experimental and numerical studies are performed on Alloy 617 at 950°C using notch specimen geometries under CF loading in this study.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Progress Report on Alloy 709 Base Metal Code Case Testing at ORNL in FY 2023

A collaborative research and development effort in support of the Alloy 709 Code Case qualification in the American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel Code, Section III, Division 5, High Temperature Reactors is being carried out at Oak Ridge National Laboratory (ORNL), Idaho National Laboratory (INL) and Argonne National Laboratory (Argonne). In FY 2023, ORNL has continued to conduct a subset of the Code Case testing for tensile, creep rupture, fatigue and creep-fatigue on Alloy 709. This report also updates the key Code Case testing status and results on the first two commercial heats and the preliminary results on the third commercial heat of Alloy 709. The three commercial heats of Alloy 709 are all in plate product form.

36 MATERIALS SCIENCE↗

Research Plan and Preliminary Results in Developing the Fabrication Parameters for Alloy 709 in Different Product Forms―Grain Coarsening Temperature Evaluation

The Advanced Reactor Technologies (ART) Program has established a multi-year plan to develop Alloy 709 advanced stainless steel (A709), generate the data package and develop material-specific design parameters in qualifying it as a new structural material for Class A component design in the American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel Code, Section III, Division 5, High Temperature Reactors. In collaboration with material vendors, the Advanced Materials Development activities under ART have successfully scaled the A709 plate form production from a laboratory heat of 500 pounds to commercial heats totaling 133,000 pounds of A709 plate fabricated from three heats. The goal of the overall A709 development program is to establish the necessary microstructural and mechanical properties relationship for A709 to ultimately develop fabrication parameters for other product forms such as bars, piping and forging using the available ART A709 materials. The objective of this A709 development work at ORNL in FY2023 is to experimentally determine grain coarsening behavior for the A709 heats and to experimentally generate the continuous cooling precipitation (CCP) diagram for A709 using the as-rolled commercial heat plate materials. Integral to this work is the characterization of the as-rolled materials and the determination of an effective solution annealing process. This report summarizes the work performed to identify the grain coarsening temperature for commercial heat 58776-3RB fabricated by G. O. Carlson and heat 529900-02 fabricated by Allegheny Technologies Incorporated (ATI) Flat Rolled Products.

36 MATERIALS SCIENCE↗

Gaseous hydrogen storage system with cryogenic supply

A gaseous hydrogen storage and distribution system with a cryogenic supply and a method for the cryogenic conversion of liquid hydrogen into high-pressure gaseous hydrogen are provided. The gaseous hydrogen storage and distribution system includes pressuring liquid hydrogen from a cryogenic tank using a low pressure liquid pump before vaporization within a relatively small vaporizer. The resulting high pressure gaseous hydrogen is transferred to a plurality of storage tanks at ambient temperature according to a desired fill sequence. The high pressure hydrogen gas is subsequently distributed from the storage tanks through a hydrogen fueling dispenser according to a desired dispensing sequence. The present system and method provide improvements in operational safety, eliminates the use of high pressure gas compressor, and minimizes boiling off and ventilation losses at a reduced cost when compared to existing thermal compression storage systems.

Feng, Zhili↗