Engineering topics
Wang, W.
Publications and source records attributed to Wang, W..
Topological background discrimination in the PandaX-III neutrinoless double beta decay experiment
The PandaX-III experiment plans to search for neutrinoless double beta decay (0ν ββ ) of 136 Xe in the China JinPing underground Laboratory (CJPL). The experiment will use a high pressure gaseous time projection chamber (TPC) to register both the energy and the electron track topology of an event. This article is devoted to demonstrate our particular detector setup capabilities for the identification of 0ν ββ and the consequent background reduction. As software tool we use REST, a framework developed for the reconstruction and simulation of TPC-based detector systems. We study the potential for background reduction by introducing appropriate parameters based on the properties of 0ν ββ events. We exploit for the first time not only the energy density of the electron track-ends, but also the electron scattering angles produced by an electron near the end of its trajectory. To implement this, we have added new algorithms for detector signal and track processing inside REST. Their assessment shows that background can be reduced by about 7 orders of magnitude while keeping 0ν ββ efficiency above 20% for the PandaX-III baseline readout scheme, a two-dimensional 3 mm pitch stripped readout. More generally, we use the potential of REST to handle 2D/3D data to assess the impact on signal-to-background significance at different detector granularities, and to validate the PandaX-III baseline choice. Finally, we demonstrate the additional potential to discriminate surface background events generated at the readout plane in the absence of to, by making use of event parameters related with the diffusion of electrons.
Shear-band cavities and strain hardening in a metallic glass revealed with phase-contrast x-ray tomography
Using high-energy x-ray tomography we show that deformed Zr-based metallic-glass samples contain large amounts of shear-band cavities (internal cracks). Since the investigated samples were unloaded prior to fracture, the three-dimensionally reconstructed samples can be used to determine the true load-bearing area, which leads to the conclusion that the samples have hardened considerably during deformation. We propose how such apparent strain hardening can be caused by a change in friction condition between the detached surfaces instead of searching for an intrinsic hardening mechanism. These results indicate the importance of knowing the true load-bearing area for correct flow-stress determinations of metallic glasses.
Characterization of seminal plasma proteomic alterations associated with the IVF and rescue‐ICSI pregnancy in assisted reproduction
Abstract Background Seminal plasma is a promising diagnostic fluid for male infertility. In assisted reproduction, the seminal plasma‐based characteristics of normozoospermic men achieving successful clinical pregnancy through rescue intracytoplasmic sperm injection after in vitro fertilization failure remain unclear. Objective To identify potential seminal plasma proteins to contribute to a new understanding of unexplained male factor infertility. Materials and Methods An approach with isobaric tags for relative and absolute quantification labeling coupled with liquid chromatography matrix‐assisted laser desorption ionization mass spectrometry was applied to investigate differentially expressed proteins in the seminal plasma of a rescue intracytoplasmic sperm injection pregnancy group versus an in vitro fertilization pregnancy group of normozoospermic men. Result(s) The present work revealed seventy‐three differentially expressed seminal plasma proteins between the in vitro fertilization and rescue intracytoplasmic sperm injection groups. Forty‐five proteins were upregulated, and 28 proteins were downregulated in the rescue intracytoplasmic sperm injection group compared with the in vitro fertilization group. Bioinformatics analyses showed that these altered proteins were involved in various functions, including the kallikrein‐related proteolytic cascade, immune response, and heparin binding. Furthermore, the validity of the proteomic results was verified by Western blot analysis of the proteins (lactoferrin [LTF], fibronectin [FN1], creatine kinase B type [CKB], kallikrein‐2 [KLK2], aminopeptidase N [ANPEP], extracellular matrix protein 1 [ECM1], glycodelin [PAEP], alpha‐1‐antitrypsin [SERPINA1], and semenogelin‐1 [SEMG1]) and immunofluorescence. Moreover, 16% of the seminal plasma proteins identified in the present work have not been reported in previous studies. Discussion This panel of altered seminal plasma proteins associated with unexplained male factor infertility might have clinical relevance and may be useful in the diagnosis and prognosis of idiopathic infertility in in vitro fertilization. Conclusions Our work not only provides a new complementary high‐confidence dataset of seminal plasma proteins but also shines new light onto the molecular characteristics of seminal plasma from normozoospermic men with different assisted reproductive outcomes.
Longitudinal Gradients in Tree Stem Greenhouse Gas Concentrations Across Six Pacific Northwest Coastal Forests
Not Available
Carbon isotopic signatures of super-deep diamonds mediated by iron redox chemistry
Among redox sensitive elements, carbon is specifically important because it may have been a driver rather than a passive recorder of Earth’s redox evolution. The extent to which the isotopic composition of carbon records the redox processes that shaped the Earth is still debated. In particular, the highly reduced deep mantle may be metal-saturated, yet, it is still unclear how the presence of metallic phases influences the carbon isotopic compositions of super-deep diamonds. Here we report ab initio results for the vibrational properties of carbon in carbonates, diamond, and Fe 3 C under pressure and temperature conditions relevant to super-deep diamond formation. Previous work on this question neglected the effect of pressure on the equilibrium carbon isotopic fractionation between diamond and Fe 3 C but our calculations show that this assumption overestimates the fractionation by a factor of ~1.3. Our calculated probability density functions for the carbon isotopic compositions of super-deep diamonds derived from metallic melt can readily explain the very light carbon isotopic compositions observed in some super-deep diamonds. Our results therefore support the view that metallic phases are present during the formation of super-deep diamonds in the mantle below ~250 km.
Grain boundary segregation and intermetallic precipitation in coarsening resistant nanocrystalline aluminum alloys
In-spite of all of the unique properties of nanocrystalline materials, they are notorious when it comes to their susceptibility to thermally induced grain coarsening, thus imposing an upper limit to their application temperature. In this study, we demonstrate a coupled Monte Carlo-molecular dynamics simulation-guided experimental approach of improving the resistance to thermally induced grain coarsening in light-weight nanocrystalline Al-Mg alloys. The structure, grain boundary segregation of Mg, and extent of grain coarsening of the Al-Mg alloys were characterized using plan view and cross-sectional transmission electron microscopy and atom probe tomography. Coarsening resistance is attributed to a combination of thermodynamic stabilization of grain boundaries by controlled Mg segregation, and kinetic stabilization through pinning of the boundaries with nanoscale intermetallic precipitates. Thus, we highlight the opportunities in extending the upper limit of application temperature for nanocrystalline alloys by using a complementary thermodynamic and kinetic stabilization approach.
The PROSPECT reactor antineutrino experiment
The Precision Reactor Oscillation and Spectrum Experiment, PROSPECT, is designed to make both a precise measurement of the antineutrino spectrum from a highly-enriched uranium reactor and to probe eV-scale sterile neutrinos by searching for neutrino oscillations over meter-long baselines. PROSPECT utilizes a segmented 6 Li-doped liquid scintillator detector for both efficient detection of reactor antineutrinos through the inverse beta decay reaction and excellent background discrimination. PROSPECT is a movable 4-ton antineutrino detector covering distances of 7 m to 13 m from the High Flux Isotope Reactor core. It will probe the best-fit point of the v¯ e disappearance experiments at 4 σ in 1 year and the favored regions of the sterile neutrino parameter space at more than 3σ in 3 years. PROSPECT will test the origin of spectral deviations observed in recent θ 13 experiments, search for sterile neutrinos, and address the hypothesis of sterile neutrinos as an explanation of the reactor anomaly. This study describes the design, construction, and commissioning of PROSPECT and reports first data characterizing the performance of the PROSPECT antineutrino detector.
First Search for Short-Baseline Neutrino Oscillations at HFIR with PROSPECT
Not Available
A comparative research on bobbin tool and conventional friction stir welding of Al-Mg-Si alloy plates
Highlights: • 6061-T4 Al plates were successfully welded by both BT-FSW and C-FSW processes. • A wide welding parameter window was achieved with bobbin tool. • BT-FSW joints showed good strength similar to that of C-FSW joints. • Proving that an Isothermal Dissolution Layer Theory also apply to BT-FSW - Abstract: In our work, Al-Mg-Si (6061Al -T4) plates of 6 mm thickness were subjected to bobbin tool friction stir welding (BT-FSW) and conventional friction stir welding (C-FSW) for comparison. How the welding process affects the microstructure and mechanical properties was investigated at various rotation rates and welding speeds. The results showed that butt FSW joints with high quality could be produced at the selected parameters. The joint strength rose with enhanced welding speed and was nearly independent of the rotation rate in both the welding processes. The strength of the joints produced with BT-FSW reached the same level as that of the C-FSW. The maximum joint strength of 229 MPa was 93% of the base material (BM), which is superior to the reported results of 60–80% for the T4 condition. The fracture position of most of the joints was in the heat-affected zone (HAZ), which is the lowest hardness zone.
Electron mass enhancement and magnetic phase separation near the Mott transition in double-layer ruthenates
Here, we present a detailed investigation of the specific heat of Ca 3 (Ru 1-x M x ) 2 O 7 (M = Ti, Fe, Mn) single crystals. Depending on the dopant and doping level, three distinct regions are present: a quasitwo-dimensional metallic state with antiferromagnetic (AFM) order formed by ferromagnetic bilayers (AFM-b), a Mott insulating state with G-type AFM order (G-AFM), and a localized state with a mixed AFM-b and G-AFM phase. Our specific heat data provide deep insights into the Mott transitions induced by Ti and Mn doping. We observed not only an anomalous large mass enhancement, but also an additional term in the specific heat, i.e., C ∝ T 2 , in the localized region. The C ∝ T 2 term is most likely due to long-wavelength excitations with both FM and AFM components. A decrease in the Debye temperature is observed in the G-type AFM region, indicating lattice softening associated with the Mott transition.
Effect of Annealing Temperature on Broad Luminescence of Silver-Exchanged Zeolites Y and A
The annealing temperature dependence of luminescence properties of silver (Ag)-exchanged zeolites Y and A was studied. It was found that the absorbance and excitation/emission bands are strongly affected by the thermal treatments. With increase in annealing temperature, the absorbance of Ag in zeolite Y increases at first and then decreases. However, the position of the excitation/emission band in zeolite Y was found to be insensitive to the annealing temperature. In contrast, the excitation/emission bands in zeolite A are particularly sensitive to the annealing temperature. The difference of such temperature dependence in zeolites Y and A may be due to the different microporous structure of the two minerals. Moreover, the fact that this dependence is not observed in Ag-exchanged zeolite Y is likely to be due to the difficulty in dehydration of zeolite Y in air or due to the weak Ag{sup +}–Ag{sup +} interaction in zeolite Y.
Evaluation of the Neutron Data Standards
With the need for improving existing nuclear data evaluations, (e.g., ENDF/B-VIII.0 and JEFF-3.3 releases) the first step was to evaluate the standards for use in such a library. This new standards evaluation made use of improved experimental data and some developments in the methodology of analysis and evaluation. In addition to the work on the traditional standards, this work produced the extension of some energy ranges and includes new reactions that are called reference cross sections. Since the effort extends beyond the traditional standards, it is called the neutron data standards evaluation. This international effort has produced new evaluations of the following cross section standards: the H(n,n), 6 Li(n,t), 10 B(n,α), 10 B(n,α 1 γ), nat C(n,n), Au(n,γ), 235 U(n,f) and 238 U(n,f). Also in the evaluation process the 238 U(n,γ) and 239 Pu(n,f) cross sections that are not standards were evaluated. Evaluations were also obtained for data that are not traditional standards: the Maxwellian spectrum averaged cross section for the Au(n,γ) cross section at 30 keV; reference cross sections for prompt γ-ray production in fast neutron-induced reactions; reference cross sections for very high energy fission cross sections; the 252 Cf spontaneous fission neutron spectrum and the 235 U prompt fission neutron spectrum induced by thermal incident neutrons; and the thermal neutron constants. The data and covariance matrices of the uncertainties were obtained directly from the evaluation procedure.
Comparative modelling of the coupled thermal–hydraulic-mechanical (THM) processes in a heated bentonite pellet column with hydration
For the deep geological disposal of high-level radioactive waste in argillaceous rocks, the heat production of the waste is an important driver for thermal–hydraulic-mechanical (THM)-coupled processes. These THM processes influence the properties and conditions of the near field that in many repository designs contains bentonite as a clay buffer. One task in the DECOVALEX-2015 (DEvelopment of COupled models and their VALidation against Experiments) project was the modelling of a heated bentonite column (Villar et al. in Long-term THM tests reports: THM cells for the HE-E test: update of results until February 2014. Deliverable-no: D2.2-7.3. CIEMAT Technical Report IEMAT/DMA/2G210/03/2014, 2014) in preparation for the in situ heater experiment HE-E at the underground rock laboratory Mont Terri. DECOVALEX is an international cooperative project that focuses on the development and validation of mathematical models for simulating such coupled processes associated with disposal in deep geological repositories. Eight modelling teams developed their own THM-coupled models for the bentonite column experiment, using six different simulation codes. Each of the teams individually calibrated the THM parameters for the bentonite material. The eight resulting parameter sets agree well and allow a satisfactory reproduction of the TH measurements by all models. The modelling results for the evolution of temperature and relative humidity over time at three sensors in the bentonite column are in good agreement between the teams and with the measured data. Also, changes of the temperature due to modifications of the insulation and the adjustment of the heating power during the course of the experiment are well reproduced. The models were thus able to reproduce the main physical processes of the experiment, both for vapour-dominated diffusion during the heating phase and combined liquid and vapour transport during a subsequent heating and hydration phase. Lastly, based on the parameter sets, the teams predict a penetration of the water infiltration front in the 48-cm column filled with bentonite pellets to a depth between 25 and 35 cm over the 15,000 h (i.e. over 20 months) of the hydration phase of the experiment.
Design and Analysis Progress of ITER Diagnostic Equatorial Port #09
ITER is the world's largest fusion device currently under construction in the South of France with >50 diagnostic systems to be installed inside the port plugs (PPs), the interspace (IS), or the port cell region of various diagnostic ports. The plasma facing diagnostic first wall (DFW) and its supporting diagnostic shield modules (DSM) are designed to protect front-end diagnostics from plasma neutron and plasma radiation, while providing apertures for diagnostic access to the plasma. The design of ITER port plug structures including the DFW and the DSM is largely driven by the electromagnetic loads included on the PP structural components during plasma major disruptions and the vertical displacement events (VDEs). Unlike DFW and DSM, the design of diagnostic system, however, is likely driven by the steady-state thermal loads from plasma volumetric and surface heating and the dynamic response of the in-port components attached to the port-specific DSM or closure plate under transient loads induced on the vacuum vessel and the port extension during asymmetric VDEs. Three tenant diagnostic systems are integrated into the equatorial port 09. The toroidal interferometer/polarimeter, or TIP system, is installed in the left drawer (DSM3, left looking from plasma) for measuring the plasma density so to control the fuel input. The electron cyclotron emission (ECE) system is installed in the middle drawer (DSM2) to provide the high spatial and temporal resolution measurements of electron temperature evolution and the electron thermal transport inferences. The visible/infrared wide angle viewing system is installed in the right drawer (DSM1) to provide visible and infrared viewing and temperature data of the first wall for its protection in support of machine operation. The port plug integration design and multiphysics analyses are performed following port integration requirements including the weight limit (45 tones total), shut down dose rate limits, the cooling/heating and structural integrity validation. Mass distribution for TIP and ECE DSMs has been optimized to minimize the total weight by a new design of the boron carbide shielding pocket. Furthermore, the lightened DSM maintains its front-end load distribution and the structural stiffness with minimum impact to the DFW so to better protect on-board diagnostics; while still provides sufficient front-end stiffness for its structural integrity as well as the diagnostics function requirements.
Uncertainty in the response of terrestrial carbon sink to environmental drivers undermines carbon-climate feedback predictions
Terrestrial ecosystems play a vital role in regulating the accumulation of carbon (C) in the atmosphere. Understanding the factors controlling land C uptake is critical for reducing uncertainties in projections of future climate. The relative importance of changing climate, rising atmospheric CO2, and other factors, however, remains unclear despite decades of research. Here, we use an ensemble of land models to show that models disagree on the primary driver of cumulative C uptake for 85% of vegetated land area. Disagreement is largest in model sensitivity to rising atmospheric CO2 which shows almost twice the variability in cumulative land uptake since 1901 (1 s.d. of 212.8 PgC vs. 138.5 PgC, respectively). We find that variability in CO2 and temperature sensitivity is attributable, in part, to their compensatory effects on C uptake, whereby comparable estimates of C uptake can arise by invoking different sensitivities to key environmental conditions. Conversely, divergent estimates of C uptake can occur despite being based on the same environmental sensitivities. Together, these findings imply an important limitation to the predictability of C cycling and climate under unprecedented environmental conditions. We suggest that the carbon modeling community prioritize a probabilistic multi-model approach to generate more robust C cycle projections.