Engineering Papers⌕ Search

Engineering topics

Wang, L.

Publications and source records attributed to Wang, L..

At least 73 records · Page 4

Start-to-end self-consistent simulation of the UEM beamline

Addressing the preliminary design review report of the ultrafast electron microscope (UEM), start-to-end self-consistent simulations were carried out to explore fundamental aspects affecting the resolution (space-charge effects, energy spread, shot-to-shot energy jitter, contrast formation, etc.). The electron beam energy spread in the single-shot mode and the effective energy spread in the accumulation mode, equivalent to the convolution of the single-shot energy spread and shot-to-shot energy jitter, have been identified as the ultimate limits of the instrument resolution. A full self-consistent simulation from the photocathode to the detector is being performed using the GPT code to find out what resolution can be achieved. Preliminary results of the start-to-end simulations are reported in this note and the plan of further simulations is presented.

43 PARTICLE ACCELERATORS↗

OC6 Phase I: Investigating the underprediction of low-frequency hydrodynamic loads and responses of a floating wind turbine

Phase I of the OC6 project is focused on examining why offshore wind design tools underpredict the response (loads/motion) of the OC5-DeepCwind semisubmersible at its surge and pitch natural frequencies. Previous investigations showed that the underprediction was primarily related to nonlinear hydrodynamic loading, so two new validation campaigns were performed to separately examine the different hydrodynamic load components. In this paper, we validate a variety of tools against this new test data, focusing on the ability to accurately model the low-frequency loads on a semisubmersible floater when held fixed under wave excitation and when forced to oscillate in the surge direction. However, it is observed that models providing better load predictions in these two scenarios do not necessarily produce a more accurate motion response in a moored configuration.

17 WIND ENERGY↗

An improved ten-moment closure for reconnection and instabilities

The integration of kinetic effects in fluid models is important for global simulations of Earth's magnetosphere. The use of the two-fluid ten-moment model, which includes the pressure tensor for both species, has had some success in simulating Ganymede and Mercury with a simple closure model. Here, we discuss a heat flux closure which accounts for some limitations of the earlier work while remaining computationally tractable. Comparisons with kinetic simulations for magnetic reconnection and lower-hybrid drift instabilities show good agreement with kinetic results and improvements on previous closure models.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Simulation of divertor heat flux width on EAST by BOUT++ transport code

The BOUT++ edge plasma transport code is applied to study the effects of neutral recycling, drifts and heating scheme on edge plasma profiles and the divertor heat flux width of two discharges of the experimental advanced superconducting tokamak (EAST) steady-state H-mode plasmas heated by low hybrid wave (LHW) and neutral beam (NB), respectively. Neutral recycling seems to have played an important role in the plasma density profile. The edge plasma density drops dramatically for the case w/o neutral recycling, while it can be sustained for the case w/ neutral recycling. Drifts are found to have significant influences on edge plasma profiles. Both the amplitude and width of the divertor heat flux are found to have increased a lot due to drifts. The simulated heat flux width w/ drifts for the two discharges shows reasonable agreement with the experiments. However, the width from the simulation and experiment for the LHW heated discharge is much larger than that of the NB heated discharge. Comparison with Goldston's drift-based model and more detailed analysis on the heat flux contributions from drifts versus turbulence show that drifts are the dominant factor in edge plasma transport for both LHW and NB heated discharges, while turbulence may have played a more important role in determining the heat flux width in LHW heated discharges than that in NB heated discharges. This may account for the larger heat flux width in the LHW heated discharge. The magnetic topology and the equilibrium change by the LHW power may also be a potential reason for the larger heat flux width in the LHW heated discharges, which still needs more evidence and studies to support it. Finally, additional SOLPS simulation w/o drifts for the two discharges show reasonable agreement with the counterpart from the BOUT++ simulation, suggesting the two are both suitable codes for EAST edge plasma simulation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

BSE versus StarTrack: Implementations of new wind, remnant-formation, and natal-kick schemes in NBODY7 and their astrophysical consequences

As a result of their formation via massive single and binary stellar evolution, the masses of stellar-remnant black holes (BH) are subjects of great interest in this era of gravitational-wave detection from binary black hole (BBH) and binary neutron star merger events. In this work, we present new developments in the stellar-remnant formation and related schemes of the current N-body evolution program NBODY7. We demonstrate that the newly implemented stellar-wind and remnant-formation schemes in the stellar-evolutionary sector or BSE of the NBODY7 code, such as the “rapid” and the “delayed” supernova (SN) schemes along with an implementation of pulsational-pair-instability and pair-instability supernova (PPSN/PSN), now produce neutron star (NS) and BH masses that agree nearly perfectly, over large ranges of zero-age-main-sequence (ZAMS) mass and metallicity, with those from the widely recognised StarTrack population-synthesis program. We also demonstrate the new, recipe-based implementations of various widely debated mechanisms of natal kicks on NSs and BHs, such as “convection-asymmetry-driven”, “collapse-asymmetry-driven”, and “neutrino-emission-driven” kicks, in addition to a fully consistent implementation of the standard, fallback-dependent, momentum-conserving natal kick. All the above newly implemented schemes are also shared with the standalone versions of SSE and BSE. Furthermore, all these demonstrations are performed with both the updated standalone BSE and the updated NBODY7/BSE. When convolved with stellar and primordial-binary populations as observed in young massive clusters, such remnant-formation and natal-kick mechanisms crucially determine the accumulated number, mass, and mass distribution of the BHs retained in young massive, open, and globular clusters (GCs); these BHs would eventually become available for long-term dynamical processing. Among other conclusions, we find that although the newer, delayed SN remnant formation model gives birth to the largest number (mass) of BHs, the older remnant-formation schemes cause the largest number (mass) of BHs to survive in clusters, when incorporating SN material fallback onto the BHs. The SN material fallback also causes the convection-asymmetry-driven SN kick to effectively retain similar numbers and masses of BHs in clusters as for the standard, momentum-conserving kick. The collapse-asymmetry-driven SN kick would cause nearly all BHs to be retained in clusters irrespective of their mass, remnant-formation model, and metallicity, whereas the inference of a large population of BHs in GCs would potentially rule out the neutrino-driven SN kick mechanism. Pre-SN mergers of massive primordial binaries would potentially cause BH masses to deviate from the theoretical, single-star ZAMS to mass-remnant mass relation unless a substantial of the total merging stellar mass of up to ≈40% is lost during a merger process. In particular, such mergers, at low metallicities, have the potential to produce low-spinning BHs within the PSN mass gap that can be retained in a stellar cluster and be available for subsequent dynamical interactions. As recent studies indicate, the new remnant-formation modelling reassures us that young massive and open clusters would potentially contribute to the dynamical BBH merger detection rate to a similar extent as their more massive GC counterparts.

79 ASTRONOMY AND ASTROPHYSICS↗

First Evidence of Local E × B Drift in the Divertor Influencing the Structure and Stability of Confined Plasma near the Edge of Fusion Devices

The structure of the edge plasma in a magnetic confinement system has a strong impact on the overall plasma performance. Here we uncover for the first time a magnetic-field-direction dependent density shelf, i.e., local flattening of density radial profile near the magnetic separatrix, in high confinement plasmas with low edge collisionality in the DIII-D tokamak. The density shelf is correlated with a doubly peaked density profile near the divertor target plate, which tends to occur for operation with the ion BX∇B drift direction away from the X-point, as currently employed for DIII-D advanced tokamak scenarios. This double-peaked divertor plasma profile is connected via the EXB drifts, arising from a strong radial electric field induced by the radial electron temperature gradient near the divertor target. The drifts lead to the reversal of the poloidal flow above the divertor target, resulting in the formation of the density shelf. The edge density shelf can be also enhanced at higher heating power, preventing large, periodic bursts of the plasma, i.e. Edge-localized Modes, in the edge region, consistent with ideal magnetohydrodynamics calculations.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Electronic Structure, Optical Properties, and Photoelectrochemical Activity of Sn-Doped Fe 2 O 3 Thin Films

Hematite (Fe 2 O 3 ) is a well-known oxide semiconductor suitable for photoelectrochemical (PEC) water splitting and industry gas sensing. It is widely known that Sn doping of Fe 2 O 3 can enhance the device performance, yet the underlying mechanism remains elusive. In this work, we determine the relationship between electronic structure, optical properties and PEC activity of Sn doped Fe 2 O 3 by studying highly crystalline, well-controlled thin films prepared by pulsed laser deposition (PLD). We show that Sn doping substantially increases the n-type conductivity of Fe 2 O 3 , and the conduction mechanism is better described by small-polaron hoping (SPH) model. Only 0.2% Sn doping significantly reduce the activation energy barrier for SPH conduction from at least 0.5 eV for undoped Fe 2 O 3 to 0.14 eV for doped ones. A combination of X-ray photoemission, X-ray absorption spectroscopy and DFT calculations reveals the Fermi level gradually shifts toward the conduction band minimum with Sn doping. A localized Fe 2+ like gap state is observed at the top of valence band, accounting for the SPH conduction. Interestingly, in contrast to the literature, we find that only 0.2% Sn doping in Fe 2 O 3 significantly improves the PEC activity, while more Sn decreases it. The improved PEC activity is partially attributed to an increased band bending potential which facilitates the charge separation at space charge region. The reduced activation energy barrier for SPH will facilitate the transport of photo-excited carriers for the enhanced PEC, which is of interest for further carrier dynamics study.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Control of hydrogen content and fuel recycling for long pulse high performance plasma operation in EAST

Control of fuel recycling and hydrogen content in the Experimental Advanced Superconducting Tokamak (EAST) using various methods is studied for high-power long pulse high confinement mode (H-mode) plasma operation. The results show that long duration first wall baking and discharge cleaning in EAST provides the necessary clean vacuum environment with a high ultimate vacuum of 3.6 × 10 -6 Pa and low outgassing rate of ~1.5 × 10 -4 Pa m 3 s -1 for plasma operation. In-vessel cryopumps are found to provide an efficient method for particle recycling control in the divertor region to decrease global recycling coefficient (R global ) from ~1.0 to ~0.8 during ohmic heating plasmas, and it provides a high particle exhausting rate of 10 20_ 10 21 D-atoms s -1 in high-power plasma operations. Long duration silicon coating is found to be more powerful than baking and discharge cleaning, which reduces the H/(H + D) ratio gradually to a value as low as 8%, and lithium coating is more effective and more efficient than silicon coating, to further reduce the H/(H + D) ratio to 3%. Real-time lithium powder injection is a novel method for recycling control, which reduces R global from 0.94 to 0.82 under lithium coating wall conditioning. By the combination and optimization of the above methods, H-mode plasmas with low hydrogen content and low fuel recycling have been achieved in EAST and have been extended gradually to 101 s in 2017. Recycling flux has even decreased gradually during 101 s H-mode plasmas due to increased first wall temperature and the resulting increased Li-II emission. These results provide valuable references on hydrogen content and fuel recycling control for long pulse H-mode plasmas of up to 400–1000 s with high-power heating in EAST and future fusion devices.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Edge turbulence evolution and intermittency development near the density limit on the HL-2A tokamak

The development of intermittent non-Gaussian processes is researched in the edge turbulence of ohmically heated HL-2A discharges approaching the density limit. As the density limit is approached, the E × B shear flow at the last closed flux surface (LCFS) weakens, a strong positive skewness develops in the scrape-off layer (SOL), and negative skewness develops inside the LCFS of turbulent density fluctuations. A conditional averaging analysis confirms more frequent increased amplitude positive (negative) going density fluctuation activity in the SOL (inside the LCFS) as the density limit is approached. The measured turbulent stress across the edge, LCFS, and SOL region is decomposed into diffusive and residual stress components, and the nonlinear exchange of kinetic energy between the turbulence and the low-frequency E × B shear flow is determined. Residual stress acts to amplify the E × B flow at the LCFS, while the diffusive stress acts to dissipate the flow just inside this region, at the interface between the core plasma and the LCFS. The relative strength of the flow drive associated with the residual stress weakens as the density limit is approached, while the turbulent viscosity associated with the diffusive stress increases at high density. The adiabatic parameter, k z 2 v th 2 / ω ν e , drops significantly to about 0.5 in the SOL when the density limit is approached, indicating a transition from the adiabatic regime to the hydrodynamic regime due to increased collisionality. Such changes enhance the particle transport through the nonadiabatic electron response and hence should end in a stronger edge cooling at fixed edge plasma heat flux.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

An Extended MHD Study of the 16 October 2015 MMS Diffusion Region Crossing

The Magnetospheric Multiscale (MMS) mission has given us unprecedented access to high cadence particle and field data of magnetic reconnection at Earth's magnetopause. MMS first passed very near an X-line on 16 October 2015, the Burch event, and has since observed multiple X-line crossings. Subsequent 3-D particle-in-cell (PIC) modeling efforts of and comparison with the Burch event have revealed a host of novel physical insights concerning magnetic reconnection, turbulence-induced particle mixing, and secondary instabilities. In this study, we employ the Gkeyll simulation framework to study the Burch event with different classes of extended, multifluid magnetohydrodynamics (MHD), including models that incorporate important kinetic effects, such as the electron pressure tensor, with physics-based closure relations designed to capture linear Landau damping. Such fluid modeling approaches are able to capture different levels of kinetic physics in global simulations and are generally less costly than fully kinetic PIC. Herein we focus on the additional physics one can capture with increasing levels of fluid closure refinement via comparison with MMS data and existing PIC simulations. In particular, we find that the ten-moment model well captures the agyrotropic structure of the pressure tensor in the vicinity of the X-line and the magnitude of anisotropic electron heating observed in MMS and PIC simulations. However, the ten-moment model is found to have difficulty resolving the lower hybrid drift instability, which plays a fundamental role in heating and mixing electrons in the current layer.

79 ASTRONOMY AND ASTROPHYSICS↗

Peierls barrier characteristic and anomalous strain hardening provoked by dynamic-strain-aging strengthening in a body-centered-cubic high-entropy alloy

The temperature effect on the mechanical behavior of the HfNbTaTiZr high entropy alloy (HEA) was investigated at 77–673 K. The decrease of the yield strength with increasing the temperature was mechanistically analyzed by considering contributions from various strengthening mechanisms. An anomalous dependence of strain hardening on temperature was observed and was justified to be caused by dynamic strain aging (DSA) as an extra strengthening mechanism at elevated temperatures. A model was constructed to split the overall strain hardening into forest hardening and DSA hardening, both of which were theoretically quantified at all temperatures considered. The work quantifies the height of Peierls barriers in the bcc HfNbTaTiZr HEA, and reveals dynamic strain aging as the strengthening mechanism causing the anomalous strain hardening at elevated temperatures.

36 MATERIALS SCIENCE↗

Observation of two collapsed phases in CaRbF e 4 A s 4

We report the observation of the pressure-induced, fully collapsed tetragonal phase of $CaRbF_{e_4}As_4$ for $P ~ 22 GPa$ via high-pressure x-ray diffraction and magnetotransport measurements. The x-ray measurements, along with resistivity measurements, show that there is an initial half-collapsed tetragonal phase for $6 < P < 22$ GPa , in which superconductivity is continuously suppressed from $T_ c = 35 K$ at $P = 3.1 GP$a to $T_c < 2 K$ for $P ≥ 17.2 GPa$ , as well as signs of the fully collapsed tetragonal phase near $P = 22 GPa$. Density functional calculations suggest that both of these transitions are driven by increased As-As bonding, first across the Ca layer, and then at the second transition, across the Rb layer. Although electrical resistivity measurements in the fully collapsed tetragonal phase do not show superconductivity, there is a change in the slope of both the Hall coefficient and the longitudinal resistance near 22 GPa, suggesting a strong correlation between the electronic and lattice degrees of freedom in this new iron-based superconductor.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Overview of the recent experimental research on the J-TEXT tokamak

Recent J-TEXT research has highlighted the significance of the role that non-axisymmetric magnetic perturbations, so called three-dimensional (3D) magnetic perturbation (MP) fields, play in a fundamentally 2D concept, i.e. tokamaks. This paper presents the J-TEXT results achieved over the last two years, especially on the impacts of 3D MP fields on magnetohydrodynamic instabilities, plasma disruptions and plasma turbulence transport. On J-TEXT, the resonant MP (RMP) system, capable of providing either a static or a high frequency (up to 8 kHz) rotating RMP field, has been upgraded by adding a new set of 12 in-vessel saddle coils. The shattered pellet injection system was built in J-TEXT in the spring of 2018. The new capabilities advance J-TEXT to be at the forefront of international magnetic fusion facilities, allowing flexible study of 3D effects and disruption mitigation in a tokamak. The fast rotating RMP field has been successfully applied for avoidance of mode locking and the prevention of plasma disruption. A new control strategy, which applies pulsed RMP to the tearing mode only during the accelerating phase region, was proved by nonlinear numerical modelling to be efficient in accelerating mode rotation and even completely suppresses the mode. Remarkably, the rotating tearing mode was completely suppressed by the electrode biasing. The impacts of 3D magnetic topology on the turbulence has been investigated on J-TEXT. It is found that the fluctuations of electron density, electron temperature and plasma potential can be significantly modulated by the island structure, and a larger fluctuation level appears at the X-point of islands. The suppression of runaway electrons during disruptions is essential to the operation of ITER, and it has been reached by utilizing the 3D magnetic perturbations on J-TEXT. Finally, this may provide an alternative mechanism of runaway suppression for large-scale tokamaks and ITER.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗