Enabling a Solid State Carbon Dioxide Distribution Network (Phase I: Final Technical Report)
Explore the source record for details and available documents.
Engineering topics
Publications and source records attributed to Wang, Jun.
Explore the source record for details and available documents.
Long periodic stacking ordered phases (LPSOs), consisting of various configurations of stacking faults, play an important role in developing ultrastrong Mg alloys with moderate ductility. However, their formation mechanisms are far from clear as no apparent defects are introduced during their formation as it is commonly believed that stacking faults are induced by defects. Here, we present the atomic and electronic basis for lattice-distortion-mediated formation of stacking faults, i.e., localized face-centredcubic (FCC) structures, within a Mg-Zn-Y alloy with a hexagonal close-packed (HCP) structure. The atomic motion trajectories from ab-initio molecular dynamic simulations show that the Mg atoms occupying the nearest neighbour positions of Zn and Y solute atoms undergo a local HCP-to-FCC transition. It is revealed that a local lattice distortion caused by the solute atoms enables the Mg atoms to move and rearrange into a local FCC configuration, which is validated by high resolution scanning transmission microscopy and in-situ synchrotron X-ray diffraction. Our simulations provide profound insight into the formation mechanism of stacking faults in HCP Mg and their physical nature of phase transformations. This is not only critically important because conventional defects, such as dislocations and vacancies, are important to deformation for Mg and its alloys, but also because they serve as a potential new approach to the design of advanced Mg alloys when defects could be used to facilitate
In support of the Endocrine Disruptor Screening Program (EDSP), the U.S.EPA's Office of Research and Development (ORD) is developing high-throughput screening (HTS) approaches to identify chemicals that alter target sites in the thyroid hormone (TH) pathway. The sodium iodide symporter (NIS) is a transmembrane glycoprotein that mediates iodide uptake into the thyroid as the initial step of TH biosynthesis. Previously, we screened 293 ToxCast chemicals (ph1v2) using a HEK293T cell line expressing human NIS in parallel radioactive iodide uptake (RAIU) and cell viability assays to identify potential environmental NIS inhibitors. Here, we expanded NIS inhibitor screening for a set of 768 ToxCast Phase II (ph2) chemicals, and applied a novel computational toxicology approach based on the ToxPrint chemotype to identify chemical substructures associated with NIS inhibition. Following single-concentration screening (at 1 × 10 -4 M with a 20% inhibition cutoff), 235 samples (228 chemicals) were further tested in multipleconcentration (1 × 10 -9 - 1 × 10 -4 M) format in both RAIU and cell viability assays. The 167 chemicals that exhibited significant RAIU inhibition were then prioritized using combined RAIU and cell viability responses that were normalized relative to the known NIS inhibitor sodium perchlorate. Some of the highest ranked chemicals, such as PFOS, tributyltin chloride, and triclocarban, have been previously reported to be thyroid disruptors. In addition, several novel chemicals were identified as potent NIS inhibitors. The present results were combined with the previous ph1v2 screening results to produce two sets of binary hit-calls for 1028 unique chemicals, consisting of 273 positives exhibiting significant RAIU inhibition, and 63 positives following application of a cell viability filter. A ToxPrint chemotype-enrichment analysis identified > 20 distinct chemical substructural features, represented in > 60% of the active chemicals, as significantly enriched in each NIS inhibition hit-call space. A shared set of 9 chemotypes enriched in both hit-call sets indicates stable chemotype signals (insensitive to cytotoxicity filters) that can help guide structure-activity relationship (SAR) investigations and inform future research.
1-caffeoylglycerol (1-CG) is a hydrophilic ester with a high solubility, and has a strong activity to prevent skin cancer caused by ultraviolet. However, the current preparation process to synthesize 1-CG via transesterification from methyl caffeate (MC) and glycerin was not economic due to long reaction time or adding extra field. Therefore, an enzymatic synthesis with deep eutectic solvent chloride-urea (ChCl-urea) in a microreactor was firstly applied under continuous microflow condition to improve the productivity. A maximum 1-CG yield of 96.49% was obtained under the optimized conditions: temperature of 65 degrees C, flow rate of 2 $μ$L/min, MC concentration of 50 g/L. Compared to the batch reactor, the reaction time reduced by 75%, the $K_m$ value decreased by 5/6, the reuse times of lipase increased by 2.29-fold, the external mass and transfer coefficients increased 10 times, which process was verified by numerical simulation. In addition, the produced 1-CG of 2 mg/mL has a high UV damage remediation ability of 75.16% using HaCaT cell model, which reveals 1-CG can repair the damage of cells radiated by the UV. Thus, this approach represents a convenient and cost-saving method to produce 1-CG using microfuidic biocatalysis.
The lithium-ion battery (LIB) recycling market is becoming increasingly important because of the widespread use of LIBs in every aspect of our lives. Mobile devices and electric cars represent the largest application areas for LIBs. Vigorous innovation in these sectors is spurring continuous deployment of LIB powered devices, and consequently more and more LIBs will become waste as they approach end of life. Considering the significant economic and environmental impacts, recycling is not only necessary, but also urgent. The WPI group has successfully developed a closed-loop recycling process, and has previously demonstrated it on a relatively small scale 1 kg spent batteries per experiment. Here, we show that the closed-loop recycling process can be successfully scaled up to 30 kg of spent LIBs from electric vehicle recycling streams, and the recovered cathode powder shows similar (or better) performance to equivalent commercial powder when evaluated in both coin cells and single layer pouch cells. All of these results demonstrate the closed-loop recycling process has great adaptability and can be further developed into industrial scale.
Not Available
Concentrations, sources, and risk assessment of 16 organochlorinated pesticides (OCPs), seven polychlorinated biphenyls (PCBs) and seven polybrominated diphenyl ethers (PBDEs) were determined in soils from Kiambu to Mombasa in Kenya. The total concentrations of OCPs ranged between 7.62 and 76.09 ng/g, dominated by HCHs. Source identification displayed recent inputs and historical use of DDTs and lindane. The total concentrations of PCBs ranged from 9.90 to 20.8 ng/g with an average of 14.40 ng/g dominated by penta-PCBs from old transformers leakages. The total PBDEs concentrations were in the range of 1.89–38.36 ng/g and with a mean of 11.38 ng/g. Electric and electronic equipment waste and PBDE containing materials as sources of PBDE. The risk assessment of OCPs and PCBs showed low potential human health risk from OCPs, while PCBs indicated to pose a high risk.
The continuously increasing number and size of lithium-based batteries developed for large-scale applications raise serious environmental concerns. Herein, we address the issues related to electrolyte toxicity and safety by proposing a "water-in-ionomer" type of electrolyte which replaces organic solvents by water and expensive and toxic fluorinated lithium salts by a non-fluorinated, inexpensive and non-toxic superabsorbing ionomer, lithium polyacrylate. Interestingly, the electrochemical stability window of this electrolyte is extended greatly, even for high water contents. Particularly, the gel with 50 wt% ionomer exhibits an electrochemical stability window of 2.6 V vs. platinum and a conductivity of 6.5 mS cm -1 at 20 °C. Structural investigations suggest that the electrolytes locally self-organize and most likely switch local structures with the change of water content, leading to a 50% gel with good conductivity and elastic properties. A LiTi 2 (PO 4 ) 3 /LiMn 2 O 4 lithium-ion cell incorporating this electrolyte provided an average discharge voltage > 1.5 V and a specific energy of 77 Wh kg -1 , while for an alternative cell chemistry, i.e., TiO 2 /LiMn 2 O 4 , a further enhanced average output voltage of 2.1 V and an initial specific energy of 124.2 Wh kg -1 are achieved.
High energy–density, low–cost batteries are critically important to a variety of applications ranging from portable electronics to electric vehicles (EVs) and grid–scale storage. While tremendous research effort has been focused on new materials or chemistries with high energy–density potential, design innovations such as low–tortuosity thick electrodes are another promising path toward higher energy density and lower cost. Growing demand for fast–charging batteries has also highlighted the need for negative electrodes that can accept high rate charging without metal deposition; low tortuosity can be a benefit in this regard. However, a general and scalable fabrication method for low–tortuosity electrodes is currently lacking. Here an emulsion–based, magnetic–alignment approach to producing thick electrodes (>400 µm thickness) with ultrahigh areal capacity (up to ≈14 mAh cm –2 vs 2–4 mAh cm –2 for conventional lithium ion) is reported. The process is demonstrated for LiCoO 2 and meso–carbon microbead graphite. The LiCoO 2 cathodes are confirmed to have low tortuosity via DC–depolarization experiments and deliver high areal capacity (>10 mAh cm –2 ) in galvanostatic discharge tests at practical C–rates and model EV drive–cycle tests. Lastly, this simple fabrication method can potentially be applied to many other active materials to enable thick, low–tortuosity electrodes.
High-temperature operations present a substantial challenge for developing industrial-capable precious metal catalysts (e.g. Pt/alumina), where the scarce metal atoms easily become wasted as sintered nanoparticles. Using fully dispersed precious metal atoms to deliver the catalysis remains an elusive goal. On a widely used La-stabilized alumina support, we find that the atomically dispersed Pt 1 (II)-O x - species, rather than the much more visible large metal particles, are the actual catalytic sites for the CO and C 3 H 6 oxidation reactions. Unfortunately, the La dopants in alumina support will not hinder the sintering of the active Pt1(II)-Ox- species. As a natural next step, the Ba-Ox- species were introduced to specifically stabilize the single-atom Pt on the La-stabilized alumina support. By implementing this improved formulation, the atomically dispersed Pt on alumina retains the original full dispersion even after 650 °C hydrothermal aging. Intriguingly, with or without the barium additives and/or sintered platinum particles in the catalysts, the intrinsic activity per Pt atom stays intact. Along with other experimental evidence, this leads to the finding that the single-atom Pt is the true catalytic site for the oxidation of CO and C 3 H 6 in the widely-used Pt/La-Al 2 O 3 material system. This work provides a new perspective for efficient precious metal utilization under demanding catalytic conditions.
Highlights: • UFG Alloy 718-5 vol.%Y{sub 2}O{sub 3} alloy is fabricated from alloy machining chips. • The kind of oxide nanoparticles is identified in Nb-rich superalloys. • High thermal stable nanoparticles and UFG microstructure is achieved. • The GB strengthening effects at 25 °C and 650 °C of UFG alloy are calculated. - Abstract: An ultrafine grained (UFG) nickel base superalloy doped with 5 vol.%Y{sub 2}O{sub 3} nanoparticles, Alloy 718-5 vol.%Y{sub 2}O{sub 3}, was fabricated by a powder metallurgy route which combines high energy mechanical milling of Alloy 718 machining chips, spark plasma sintering, hot extrusion and heat treatment, and its microstructure and mechanical properties at room temperature and 650 °C were studied. The study showed that the Y{sub 2}O{sub 3} nanoparticles reacted with Al from the base alloy and transformed to Y{sub 4}Al{sub 2}O{sub 9} nanoparticles (average diameter: 12.5 nm) which were stable during heat treatment at 970 °C (0.78T{sub m}, where T{sub m} is the solidus temperature of the alloy in K). As a result of the high thermal stability of Y{sub 4}Al{sub 2}O{sub 9} nanoparticles and their effective pinning of the grain boundaries, the UFG microstructure (average grain size: 179 nm) of the alloy was stable during heat treatment. Grain boundary and nanoparticle strengthening rendered the heat treated Alloy 718-5 vol.%Y{sub 2}O{sub 3} alloy with a notable room temperature tensile yield strength of 1870 MPa. It was demonstrated that the grain boundary strengthening effect associated with the UFG microstructure was still significant at 650 °C, but clearly decreased from its level at room temperature. The grain boundary strengthening and nanoparticle strengthening effects which are likely to be independent of test temperature sustain a reasonably high tensile yield strength of 800 MPa at 650 °C, despite the absence of γ′ and γ″ precipitates in the UFG microstructure.
Transition metal sulfides are promising high capacity anodes for sodium-ion batteries in terms of the conversion reaction with multiple alkali metal ions. Nonetheless, some inherent challenges such as sluggish sodium ion diffusion kinetics, large volume change, and poor cycle stability limit their implementation. Addressing these issues necessitates a comprehensive understanding the complex sodium ion storage mechanism particularly at the initial cycle. Here, taking nickel subsulfide as a model material, we reveal the complicated conversion reaction mechanism upon the first cycle by combining in operando 2D transmission X-ray microscopy with X-ray absorption spectroscopy, ex-situ 3D nano-tomography, high-energy X-ray diffraction and electrochemical impedance spectroscopy. This study demonstrates that the microstructure evolution, inherent slow sodium ions diffusion kinetics, and slow ion mobility at the two-phase interface contribute to the high irreversible capacity upon the first cycle. Finally, such understandings are critical for developing the conversion reaction materials with the desired electrochemical activity and stability.
This study presents a process for recovering aluminum from aluminum dross (an industrial waste product) via an alkali roasting process and using it to synthesize mesoporous γ-alumina. The results show that the inherent chlorides in dross (KCl and NaCl) reduce Al extraction efficiency and should be removed first by water leaching. Use of salt-free dross increases the Al extraction rate (from 85 to 96 pct) within 90 minutes alkali roasting at 923 K (650 °C). In addition, an ammonium bicarbonate byproduct can be obtained from water leaching due to the hydrolysis of AlN, which can be used as a precipitating agent in the boehmite sol preparation. Synthesis of mesoporous γ-alumina was carried out by the sol-gel method with EO{sub 20}PO{sub 70}EO{sub 20} (P123) as a template. The prepared mesoporous γ-alumina was characterized as having a disordered mesostructure with a high pore volume of 1.02 cm{sup 3}/g and surface area of 312 m{sup 2}/g. Thus, we achieved highly efficient utilization of aluminum dross and yielded products with high added value. Mesoporous γ-alumina has potential applications in environmental remediation and catalysis.
The LiMnPO4 material with Mg2+ ion substitution in transition metal site is successfully obtained by a facile solvothermal method combining with the subsequent spray drying and pyrolysis. The TEM image shows the controlled crystalline orientation of the primary Mg-doped LiMnPO4 particle, and the three-dimensional (3D) hierarchical micronano structure and the electronic structure of the Mg-doped material are investigated by the reconstructed nanotomography and X-ray absorption spectroscopy, respectively. The uniformity of Mg2+ ions substitution at the secondary particle level is confirmed by the transmission X-ray microscopy combined with X-ray absorption near edge structure. The prepared material exhibits an excellent electrochemical performance with the capacity of 156 mAh/g at the rate of 0.1 C, and good capacity retention of 100% after 400 cycles at the rate of 1 C. The in operando synchrotron X-ray diffraction data indicate that the performance improvement of the Mg-doped materials is attributed to the changed electrochemical reaction mechanism from the typical two-phase reaction for pristine LiMnPO4 material to the two-phase reaction combined with the single-phase (solid-solution) reaction process. These findings provide a new approach and understanding on developing high-energy cathode materials for lithium-ion batteries.
For environmental and sustainability reasons, spent Li-ion batteries must be recovered and recycled so that the full promise of an electrified future is realized. Li-ion battery recycling streams pose a serious challenge to all existing recycling technologies due to their unknown and diverse chemistry. In this work, four representative recycling streams were used to demonstrate the flexibility of the recycling process developed at Worcester Polytechnic Institute (WPI) to accommodate a variable feed and generate consistent quality cathode material, LiNi 1/3 Mn 1/3 Co 1/3 O 2 (NMC111). Ni 1/3 Mn 1/3 CO 1/3( OH) 2 precursors derived from four recycling streams were produced by a hydroxide co-precipitation method in a continuous stirred tank reactor. It took two days for the co-precipitation reaction to reach steady state. A possible evolution of the precursor particles up to the steady state was proposed. Both the precursors and cathodes from these four different recycling streams exhibit similar morphology, particle size distribution, and tap density. Moreover, these recovered cathode materials display similar electrochemical properties. Surprisingly these recovered NMC111s have better rate capability than a commercial NMC111 prepared from virgin materials. The different chemical compositions of the incoming recycling streams were shown to have little observed effect on the recovered precursor and resultant cathode material generated by the WPI-developed recycling process with advantages including no sorting, low temperature, and high quality recovered battery materials. Therefore, the WPI-developed process applies to different spent Li-ion battery waste streams and is therefore general.
As a result of increasing data volume and velocity, Big Data science at exascale has shifted towards the in-situ paradigm, where large scale simulations run concurrently alongside data analytics. With in-situ, data generated from simulations can be processed while still in memory, thereby avoiding the slow storage bottleneck. However, running simulations and analytics together on shared resources will likely result in substantial contention if left unmanaged, as demonstrated in this work, leading to much reduced efficiency of simulations and analytics. Recently, virtualization technologies such as Linux containers have been widely applied to data centers and physical clusters to provide highly efficient and elastic resource provisioning for consolidated workloads including scientific simulations and data analytics. In this paper, we investigate to facilitate network traffic manipulation and reduce mutual interference on the network for in-situ applications in virtual clusters. In order to dynamically allocate the network bandwidth when it is needed, we adopt SARIMA-based techniques to analyze and predict MPI traffic issued from simulations. Although this can be an effective technique, the naïve usage of network virtualization can lead to performance degradation for bursty asynchronous transmissions within an MPI job. Here, we analyze and resolve this performance degradation in virtual clusters.