Engineering Papers⌕ Search

Engineering topics

Wang, E.

Publications and source records attributed to Wang, E..

At least 91 records · Page 5

Commissioning of the 112 MHz SRF Gun and 500 MHz bunching cavities for the CeC PoP Linac

The Coherent electron Cooling Proof-of-Principle (CeC PoP) experiment at BNL includes a short electron linac. During Phase 1, a 112 MHz superconducting RF photo-emission gun and two 500 MHz normal conducting bunching cavities were installed and are under commissioning. The paper describes the Phase1 linac layout and presents commissioning results for the cavities and associated RF, cryogenic and other sub-systems

43 PARTICLE ACCELERATORS↗

The progress of funnelling gun high voltage condition and beam test

A prototype of a high average current polarized electron funneling gun as an eRHIC injector has been built at BNL. The gun was assembled and tested at Stangenes Incorporated. Two beams were generated from two GaAs photocathodes and combined by a switched combiner field. We observed the combined beams on a YAG crystal and measured the photocurrent by a Faraday cup. The gun has been shipped to Stony Brook University and is being tested there. In this paper we will describe the major components of the gun and recent beam test results. High voltage conditioning is discussed as well.

43 PARTICLE ACCELERATORS↗

Cathode performance during two beam operation of the high current high polarization electron gun for eRHIC

Two electron beams from two activated bulk GaAs photocathodes were successfully combined during the recent beam test of the High Current High Polarization Electron gun for eRHIC. The beam test took place in Stangenes Industries in Palo Alto, CA, where the cathodes were placed in diagonally opposite locations inside the high voltage shroud. No significant cross talking between the cathodes was found for the pertinent vacuum and low average current operation, which is very promising towards combining multiple beams for higher average current. This paper describes the cathode preparation, transport and cathode performance in the gun for the combining test, including the QE and lifetimes of the photocathodes at various steps of the experiment.

43 PARTICLE ACCELERATORS↗

Round-Robin Verification and Final Development of the IEC 62788-1-5 Encapsulation Size Change Test; NREL (National Renewable Energy Laboratory)

Polymeric encapsulation materials may a change size when processed at typical module lamination temperatures. The relief of residual strain, trapped during the manufacture of encapsulation sheet, can affect module performance and reliability. For example, displaced cells and interconnects threaten: cell fracture; broken interconnects (open circuits and ground faults); delamination at interfaces; and void formation. A standardized test for the characterization of change in linear dimensions of encapsulation sheet has been developed and verified. The IEC 62788-1-5 standard quantifies the maximum change in linear dimensions that may occur to allow for process control of size change. Developments incorporated into the Committee Draft (CD) of the standard as well as the assessment of the repeatability and reproducibility of the test method are described here. No pass/fail criteria are given in the standard, rather a repeatable protocol to quantify the change in dimension is provided to aid those working with encapsulation. The round-robin experiment described here identified that the repeatability and reproducibility of measurements is on the order of 1%. Recent refinements to the test procedure to improve repeatability and reproducibility include: the use of a convection oven to improve the thermal equilibration time constant and its uniformity; well-defined measurement locations reduce the effects of sampling size -and location- relative to the specimen edges; a standardized sand substrate may be readily obtained to reduce friction that would otherwise complicate the results; specimen sampling is defined, so that material is examined at known sites across the width and length of rolls; and encapsulation should be examined at the manufacturer’s recommended processing temperature, except when a cross-linking reaction may limit the size change. EVA, for example, should be examined 100 °C, between its melt transition (occurring up to 80 °C) and the onset of cross-linking (often at 100 °C).

14 SOLAR ENERGY↗

Rising Temperatures Reduce Global Wheat Production

Crop models are essential tools for assessing the threat of climate change to local and global food production. Present models used to predict wheat grain yield are highly uncertain when simulating how crops respond to temperature. Here we systematically tested 30 different wheat crop models of the Agricultural Model Intercomparison and Improvement Project against field experiments in which growing season mean temperatures ranged from 15 degrees C to 32◦ degrees C, including experiments with artificial heating. Many models simulated yields well, but were less accurate at higher temperatures. The model ensemble median was consistently more accurate in simulating the crop temperature response than any single model, regardless of the input information used. Extrapolating the model ensemble temperature response indicates that warming is already slowing yield gains at a majority of wheat-growing locations. Global wheat production is estimated to fall by 6% for each degree C of further temperature increase and become more variable over space and time.

agriculture↗

New insights into the nuclear structure in neutron-rich 112,114,115,116,117,118Pd

New level schemes of 112,114,115,116,117,118Pd are established by means of ?–?–??–?–?, ?–?–?–??–?–?–? and ?–?(0)?–?(0) measurements of prompt fission y rays from 252Cf using the Gammasphere multi-detector array. Spins/parities were assigned to levels based on ?–??–? angular correlation measurements, level systematics and decay patterns. In the even-N isotopes 112,114,116Pd, two sets of odd-parity bands were identified and extended with spins measured in each band. The odd-parity bands with large level staggerings were interpreted as disturbed chirality with less pronounced triaxial deformations in the Pd isotopes than observed in the chiral symmetry breaking 110,112Ru with maximum triaxiality. Onset of wobbling motion was identified from the sign of the signature splitting in the ? band of even–even 114Pd, and probably also in 116Pd, as first seen in the N=68N=68 isotone 112Ru. Maximal triaxiality in Ru and Pd isotopes is found to be reached for N=68N=68, 112Ru and 114Pd, 4 neutrons more than predicted in the theoretical calculations. The new data and TRS calculations allowed a systematic study of the band crossings in the even-N112,114,116Pd and odd-N115,117Pd isotopes. Now we find a new overall, more complex shape evolution than previously proposed from triaxial prolate in 110Pd via triaxial oblate in 112Pd to nearly oblate in 114,116Pd with a large change of the triaxial deformation parameter y toward nearly oblate in the (pi g 9/2)2 alignment in 114,115,116,117,118Pd, and triaxial-prolate–triaxial-oblate shape coexisting bands in 115Pd.

112,114,115,116,117,118Pd↗

Depressed electron collector for the Gatling Gun Test Stand

An optical solution for, and the general design of an electron collector (EC) for a Gatling gun Test Stand are described. The purposes of this development were to reduce the power load on the electron gun’s high-voltage power supply, and to eliminate the back-streaming of electrons from the dump into the ultra-high-vacuum region of the beam line and the gun chamber, thereby preventing vacuum degradation. The challenge is solved by creating an effective biased “black box” on the cathode terminal for all electrons, and by assuring the vacuum separation of the EC’s volume from the beam line.

43 PARTICLE ACCELERATORS↗