Engineering Papers⌕ Search

Engineering topics

Wang, Chunyang

Publications and source records attributed to Wang, Chunyang.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Complex-Concentrated Anion Doping Enables Ultra-Stable Lattice Oxygen and Structural Integrity in Lithium-Rich Layered Oxide Cathodes

Lithium- and manganese-rich layered oxides (LMR) stand out as next-generation lithium-ion cathode chemistries, which harness both transition-metal and lattice-oxygen redox processes to deliver exceptional capacity and energy density. However, their full potential is hindered by intrinsic oxygen instability and structural degradation, resulting in pronounced voltage fade and capacity decay. Here, we present a complex-concentrated anion-doping paradigm in which multiple anions, F, Br, and S, are incorporated into the oxygen sublattice to enhance oxygen-redox and structural stability. X-ray absorption spectroscopy and aberration-corrected scanning transmission electron microscopy confirm ultra-stable local oxygen coordination environments during long-term cycling, with detrimental phase transformations and oxygen-loss-induced cavitation dramatically inhibited. Notably, we show that the characteristic LiTM6 transition metal (TM) honeycomb ordering is preserved even after electrochemical cycling. Concurrently, this strategy yields an unprecedented volume change of only 0.63% upon charging to 4.8 V vs. Li+/Li, achieving the first zero-strain LMR cathode. The resulting LMR cathode delivers ultralow voltage fade (1 mV per cycle during the first 100 cycles and becomes negligible in subsequent cycles) and outstanding energy retention (93% after 200 cycles) in a pouch cell configuration. Our complex-concentrated anion-doping concept establishes a broadly applicable strategy for resolving chemo-mechanical failure mechanisms in ceramic intercalation electrodes for next-generation energy storage.

Li-ion batteries↗
DOE OSTI2024

A Self-Healing, Flowable, Yet Solid Electrolyte Suppresses Li-Metal Morphological Instabilities

In this article, lithium metal (Li 0 ) solid-state batteries encounter implementation challenges due to dendrite formation, side reactions, and movement of the electrode–electrolyte interface in cycling. Notably, voids and cracks formed during battery fabrication/operation are hot spots for failure. Here, a self-healing, flowable yet solid electrolyte composed of mobile ceramic crystals embedded in a reconfigurable polymer network is reported. This electrolyte can auto-repair voids and cracks through a two-step self-healing process that occurs at a fast rate of 5.6 µm h -1 . A dynamical phase diagram is generated, showing the material can switch between liquid and solid forms in response to external strain rates. The flowability of the electrolyte allows it to accommodate the electrode volume change during Li 0 stripping. Simultaneously, the electrolyte maintains a solid form with high tensile strength (0.28 MPa), facilitating the regulation of mossy Li 0 deposition. The chemistries and kinetics are studied by operando synchrotron X-ray and in situ transmission electron microscopy (TEM). Solid-state NMR reveals a dual-phase ion conduction pathway and rapid Li + diffusion through the stable polymer-ceramic interphase. This designed electrolyte exhibits extended cycling life in Li 0 –Li 0 cells, reaching 12 000 h at 0.2 mA cm -2 and 5000 h at 0.5 mA cm -2 . Furthermore, owing to its high critical current density of 9 mA cm -2 , the Li 0 –LiNi 0.8 Mn 0.1 Co 0.1 O 2 (NMC811) full cell demonstrates stable cycling at 5 mA cm -2 for 1100 cycles, retaining 88% of its capacity, even under near-zero stack pressure conditions.

25 ENERGY STORAGE↗
DOE OSTI2024

Making Plasticized Polymer Electrolytes Stable Against Sodium Metal for High‐Energy Solid‐State Sodium Batteries

Abstract Solid polymer electrolytes based on plastic crystals are promising for solid‐state sodium metal (Na 0 ) batteries, yet their practicality has been hindered by the notorious Na 0 ‐electrolyte interface instability issue, the underlying cause of which remains poorly understood. Here, by leveraging a model plasticized polymer electrolyte based on conventional succinonitrile plastic crystals, we uncover its failure origin in Na 0 batteries is associated with the formation of a thick and non‐uniform solid electrolyte interphase (SEI) and whiskery Na 0 nucleation/growth. Furthermore, we design a new additive‐embedded plasticized polymer electrolyte to manipulate the Na 0 deposition and SEI formulation. For the first time, we demonstrate that introducing fluoroethylene carbonate (FEC) additive into the succinonitrile‐plasticized polymer electrolyte can effectively protect Na 0 against interfacial corrosion by facilitating the growth of dome‐like Na 0 with thin, amorphous, and fluorine‐rich SEIs, thus enabling significantly improved performances of Na//Na symmetric cells (1,800 h at 0.5 mA cm −2 ) and Na//Na 3 V 2 (PO 4 ) 3 full cells (93.0 % capacity retention after 1,200 cycles at 1 C rate in coin cells and 93.1 % capacity retention after 250 cycles at C/3 in pouch cells at room temperature). Our work provides valuable insights into the interfacial failure of plasticized polymer electrolytes and offers a promising solution to resolving the interfacial instability issue.

Zou, Peichao↗
DOE OSTI2024

Making Plasticized Polymer Electrolytes Stable Against Sodium Metal for High‐Energy Solid‐State Sodium Batteries

Solid polymer electrolytes based on plastic crystals are promising for solid-state sodium metal (Na 0 ) batteries, yet their practicality has been hindered by the notorious Na 0 -electrolyte interface instability issue, the underlying cause of which remains poorly understood. Here, in this study, by leveraging a model plasticized polymer electrolyte based on conventional succinonitrile plastic crystals, we uncover its failure origin in Na 0 batteries is associated with the formation of a thick and non-uniform solid electrolyte interphase (SEI) and whiskery Na 0 nucleation/growth. Furthermore, we design a new additive-embedded plasticized polymer electrolyte to manipulate the Na 0 deposition and SEI formulation. For the first time, we demonstrate that introducing fluoroethylene carbonate (FEC) additive into the succinonitrile-plasticized polymer electrolyte can effectively protect Na 0 against interfacial corrosion by facilitating the growth of dome-like Na 0 with thin, amorphous, and fluorine-rich SEIs, thus enabling significantly improved performances of Na//Na symmetric cells (1,800 h at 0.5 mA cm −2 ) and Na//Na 3 V 2 (PO 4 ) 3 full cells (93.0 % capacity retention after 1,200 cycles at 1 C rate in coin cells and 93.1 % capacity retention after 250 cycles at C/3 in pouch cells at room temperature). Our work provides valuable insights into the interfacial failure of plasticized polymer electrolytes and offers a promising solution to resolving the interfacial instability issue.

25 ENERGY STORAGE↗
DOE OSTI2023

Compositional inhomogeneity and its effect on the hardness of nanostructured refractory high-entropy alloys

The pronounced compositional inhomogeneity observed in refractory high-entropy alloys (HEAs), as opposed to non-refractory HEAs, has an important influence on their mechanical properties, thereby posing a significant challenge for the development of high-performance refractory HEAs. In this work, by combining transmission electron microscopy imaging, chemical analysis, and nano-hardness tests, we investigate the compositional inhomogeneities in a series of sintered nanostructured HEAs and elucidate their influence on the material's hardness. Further, we reveal that the compositional inhomogeneity of the sintered nanostructured HEAs is temperature- and component- dependent. By correlating the hardness of nanostructured HEAs to the evolving compositional inhomogeneity, our work demonstrates that the compositional inhomogeneity in nanostructured HEAs can be tuned by sintering temperature or alloying towards optimized microstructure and hardness.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2023

Anion-tethered Single Lithium-ion Conducting Polyelectrolytes through UV-induced Free Radical Polymerization for Improved Morphological Stability of Lithium Metal Anodes

Single Li + ion conducting polyelectrolytes (SICs), which feature covalently tethered counter-anions along their backbone, have the potential to mitigate dendrite formation by reducing concentration polarization and preventing salt depletion. However, due to their low ionic conductivity and complicated synthetic procedure, the successful validation of these claimed advantages in lithium metal (Li 0 ) anode batteries remains limited. In this study, we fabricated a SIC electrolyte using a single-step UV polymerization approach. The resulting electrolyte exhibited a high Li + transference number (t + ) of 0.85 and demonstrated good Li + conductivity (6.3×10 -5 S/cm at room temperature), which is comparable to that of a benchmark dual ion conductor (DIC, 9.1×10 -5 S/cm). Benefitting from the high transference number of SIC, it displayed a three-fold higher critical current density (2.4 mA/cm 2 ) compared to DIC (0.8 mA/cm 2 ) by successfully suppressing concentration polarization-induced short-circuiting. Additionally, the t + significantly influenced the deposition behavior of Li0, with SIC yielding a uniform, compact, and mosaic-like morphology, while the low t + DIC resulted in a porous morphology with Li 0 whiskers. Using the SIC electrolyte, Li 0 ||LiFePO 4 cells exhibited stable operation for 4500 cycles with 70.5 % capacity retention at 22 °C.

25 ENERGY STORAGE↗
DOE OSTI2023

Anion-tethered Single Lithium-ion Conducting Polyelectrolytes through UV-induced Free Radical Polymerization for Improved Morphological Stability of Lithium Metal Anodes

Single Li + ion conducting polyelectrolytes (SICs), which feature covalently tethered counter-anions along their backbone, have the potential to mitigate dendrite formation by reducing concentration polarization and preventing salt depletion. However, due to their low ionic conductivity and complicated synthetic procedure, the successful validation of these claimed advantages in lithium metal (Li 0 ) anode batteries remains limited. In this study, we fabricated a SIC electrolyte using a single-step UV polymerization approach. The resulting electrolyte exhibited a high Li + transference number (t + ) of 0.85 and demonstrated good Li + conductivity (6.3×10 -5 S/cm at room temperature), which is comparable to that of a benchmark dual ion conductor (DIC, 9.1×10 -5 S/cm). Benefitting from the high transference number of SIC, it displayed a three-fold higher critical current density (2.4 mA/cm 2 ) compared to DIC (0.8 mA/cm 2 ) by successfully suppressing concentration polarization-induced short-circuiting. Additionally, the t + significantly influenced the deposition behavior of Li 0 , with SIC yielding a uniform, compact, and mosaic-like morphology, while the low t + DIC resulted in a porous morphology with Li 0 whiskers. In conclusion, using the SIC electrolyte, Li 0 ||LiFePO 4 cells exhibited stable operation for 4500 cycles with 70.5 % capacity retention at 22 °C.

25 ENERGY STORAGE↗
DOE OSTI2023

Long-life lithium-ion batteries realized by low-Ni, Co-free cathode chemistry

The increasing demand for lithium-ion battery-powered electric vehicles (EVs) has led to a surge in recent prices of strategic battery materials such as cobalt (Co) and nickel (Ni). While all EV makers are eager to eliminate Co usage, Ni has rapidly become another ‘pain point’ for the industry, as its price is nearing half that of Co. The sustainability issue facing both Ni and Co puts forward a grand materials challenge, that is, to reduce Ni content and eliminate Co while maintaining high specific energy and stability. Here in this work, a complex concentrated doping strategy is used to eliminate Co in a commercial NMC-532 cathode. The LiNi 0.5 Mn 0.43 Ti 0.02 Mg 0.02 Nb 0.01 Mo 0.02 O 2 cathode shows potential cost advantage with relatively high specific energy and significantly improved overall performance (~95% capacity retained after 1,000 cycles in pouch-type cells, 2.8–4.3 V vs graphite, at 1 C, 1.5 mA cm -2 ). Combining X-ray techniques and electron microscopy, we uncover the origins of the superior stability.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Regulating Cation Interactions for Zero–Strain and High–Voltage P2–type Na 2/3 Li 1/6 Co 1/6 Mn 2/3 O 2 Layered Oxide Cathodes of Sodium–Ion Batteries

Deep sodium extraction/insertion of sodium cathodes usually causes undesired Jahn–Teller distortion and phase transition, both of which will reduce structural stability and lead to poor long-cycle reliability. Here we report a zero-strain P2- Na 2/3 Li1/6Co 1/6 Mn 2/3 O 2 cathode, in which the lithium/cobalt substitution contributes to reinforcing the host structure by reducing the Mn 3+ /Mn 4+ redox, mitigating the Jahn–Teller distortion, and minimizing the lattice change. 94.5 % of Na + in the unit structure can be reversibly cycled with a charge cut-off voltage of 4.5 V (vs. Na + /Na). Impressively, a solid-solution reaction without phase transitions is realized upon deep sodium (de)intercalation, which poses a minimal volume deviation of 0.53 %. Finally, it attains a high discharge capacity of 178 mAh g –1 , a high energy density of 534 Wh kg –1 , and excellent capacity retention of 95.8 % at 1 C after 250 cycles.

25 ENERGY STORAGE↗
DOE OSTI2023

A reactive wetting strategy improves lithium metal reversibility

The cycling of lithium metal (Li 0 ) anode is often accompanied by irregular lithium plating/stripping, leading to poor Li 0 reversibility, and posing a grand challenge to constructing reliable Li 0 batteries. Hereby, we report a reactive wetting strategy to enable conformal and highly reversible Li 0 plating/stripping through a lithium-reactive substrate. In this study, the reactive wetting, smooth nucleation, and conformal growth behaviors of Li 0 are visualized through in-situ transmission electron microscopy, ex-situ scanning electron microscope, and in-situ optical microscope characterizations. Based on the reactive wetting substrate, high average Coulombic efficiencies (99.0% at 0.5 mA cm -2 for 400 cycles) are realized for Li 0 anodes. By pre-plating Li 0 into the reactive wetting substrate as anodes and leveraging LiFePO 4 as cathodes, high capacity retention (76.0% after 200 cycles in low N/P ratio conditions) is also achieved in the as-constructed Li 0 full cells. This work establishes a fundamental understanding of reactive wetting dynamics of Li 0 and provides a drop-in solution to improving Li 0 reversibility.

25 ENERGY STORAGE↗
DOE OSTI2023

Resolving complex intralayer transition motifs in high-Ni-content layered cathode materials for lithium-ion batteries

High-Ni-content layered materials are promising cathodes for next-generation lithium-ion batteries. However, investigating the atomic configurations of the delithiation-induced complex phase boundaries and their transitions remains challenging. Here, in this study, by using deep-learning-aided super-resolution electron microscopy, we resolve the intralayer transition motifs at complex phase boundaries in high-Ni cathodes. We reveal that an O3 → O1 transformation driven by delithiation leads to the formation of two types of O1–O3 interface, the continuous- and abrupt-transition interfaces. The interfacial misfit is accommodated by a continuous shear-transition zone and an abrupt structural unit, respectively. Atomic-scale simulations show that uneven in-plane Li+ distribution contributes to the formation of both types of interface, and the abrupt transition is energetically more favourable in a delithiated state where O1 is dominant, or when there is an uneven in-plane Li + distribution in a delithiated O3 lattice. Moreover, a twin-like motif that introduces structural units analogous to the abrupt-type O1–O3 interface is also uncovered. The structural transition motifs resolved in this study provide further understanding of shear-induced phase transformations and phase boundaries in high-Ni layered cathodes.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2022

Tension‐Induced Cavitation in Li‐Metal Stripping

Abstract Designing stable Li metal and supporting solid structures (SSS) is of fundamental importance in rechargeable Li‐metal batteries. Yet, the stripping kinetics of Li metal and its mechanical effect on the supporting solids (including solid electrolyte interface) remain mysterious to date. Here, through nanoscale in situ observations of a solid‐state Li‐metal battery in an electron microscope, two distinct cavitation‐mediated Li stripping modes controlled by the ratio of the SSS thickness ( t ) to the Li deposit's radius ( r ) are discovered. A quantitative criterion is established to understand the damage tolerance of SSS on the Li‐metal stripping pathways. For mechanically unstable SSS ( t / r < 0.21), the stripping proceeds via tension‐induced multisite cavitation accompanied by severe SSS buckling and necking, ultimately leading to Li “trapping” or “dead Li” formation; for mechanically stable SSS ( t / r > 0.21), the Li metal undergoes nearly planar stripping from the root via single cavitation, showing negligible buckling. This work proves the existence of an electronically conductive precursor film coated on the interior of solid electrolytes that however can be mechanically damaged, and it is of potential importance to the design of delicate Li‐metal supporting structures to high‐performance solid‐state Li‐metal batteries.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Compositionally complex doping for zero-strain zero-cobalt layered cathodes

We report the high volatility of the price of cobalt and the geopolitical limitations of cobalt mining have made the elimination of Co a pressing need for the automotive industry. Owing to their high energy density and low-cost advantages, high-Ni and low-Co or Co-free (zero-Co) layered cathodes have become the most promising cathodes for next-generation lithium-ion batteries. However, current high-Ni cathode materials, without exception, suffer severely from their intrinsic thermal and chemo-mechanical instabilities and insufficient cycle life. Here, in this paper, by using a new compositionally complex (high-entropy) doping strategy, we successfully fabricate a high-Ni, zero-Co layered cathode that has extremely high thermal and cycling stability. Combining X-ray diffraction, transmission electron microscopy and nanotomography, we find that the cathode exhibits nearly zero volumetric change over a wide electrochemical window, resulting in greatly reduced lattice defects and local strain-induced cracks. In-situ heating experiments reveal that the thermal stability of the new cathode is significantly improved, reaching the level of the ultra-stable NMC-532. Owing to the considerably increased thermal stability and the zero volumetric change, it exhibits greatly improved capacity retention. This work, by resolving the long-standing safety and stability concerns for high-Ni, zero-Co cathode materials, offers a commercially viable cathode for safe, long-life lithium-ion batteries and a universal strategy for suppressing strain and phase transformation in intercalation electrodes.

25 ENERGY STORAGE↗
DOE OSTI2022

High-Entropy and Superstructure-Stabilized Layered Oxide Cathodes for Sodium-Ion Batteries

Layered transition metal oxides are appealing cathodes for sodium-ion batteries due to their overall advantages in energy density and cost. But their stabilities are usually compromised by the complicated phase transition and the oxygen redox, particularly when operating at high voltages, leading to poor structural stability and substantial capacity loss. Here, in this study, an integrated strategy combing the high-entropy design with the superlattice-stabilization to extend the cycle life and enhance the rate capability of layered cathodes is reported. It is shown that the as-prepared high-entropy Na 2/3 Li 1/6 Fe 1/6 Co 1/6 Ni 1/6 Mn 1/3 O 2 cathode enables a superlattice structure with Li/transition metal ordering and delivers excellent electrochemical performance that is not affected by the presence of phase transition and oxygen redox. It achieves a high reversible capacity (171.2 mAh g –1 at 0.1 C), a high energy density (531 Wh kg –1 ), extended cycling stability (89.3% capacity retention at 1 C for 90 cycles and 63.7% capacity retention at 5 C after 300 cycles), and excellent fast-charging capability (78 mAh g –1 at 10 C). This strategy would inspire more rational designs that can be leveraged to improve the reliability of layered cathodes for secondary-ion batteries.

25 ENERGY STORAGE↗
DOE OSTI2022

Localized Hydrophobicity in Aqueous Zinc Electrolytes Improves Zinc Metal Reversibility

The rechargeability of aqueous zinc metal batteries is plagued by parasitic reactions of the zinc metal anode and detrimental morphologies such as dendritic or dead zinc. To improve the zinc metal reversibility, hereby we report a new solution structure of aqueous electrolyte with hydroxyl-ions scavengers and hydrophobicity localized in solvent clusters. In this work we show that although hydrophobicity sounds counterintuitive for an aqueous system, hydrophilic pockets may be encapsulated inside a hydrophobic outer layer and a hydrophobic anode-electrolyte interface can be generated through the addition of a cation-philic, strongly anion-phobic, and OH - -reactive diluent. The localized hydrophobicity enables less active water and less absorbed water on the Zn anode surface, which suppresses the parasitic water reductions; while the hydroxyl-ion-scavenging functionality further minimizes undesired passivation layer formation, thus leading to superior reversibility (an average Zn plating/stripping efficiency of 99.72% for 1000 cycles) and lifetime (80.6% capacity retention after 5000 cycles) of zinc batteries.

25 ENERGY STORAGE↗
DOE OSTI2022

Dual Passivation of Cathode and Anode through Electrode–Electrolyte Interface Engineering Enables Long-Lifespan Li Metal–SPAN Batteries

The reliability and durability of lithium metal (Li 0 )–sulfur batteries are largely limited by the undesired Li 0 plating-stripping irreversibility and the detrimental polysulfide dissolution, yet approaches that can simultaneously address the above anodic and cathodic problems are scarce. In this study, we report the stable operation of a Li 0 -SPAN (sulfurized polyacrylonitrile) battery via an anode–cathode dual-passivation approach. By combination of a fluorinated localized high concentration electrolyte (LHCE) and a Li 3 N-forming additive (TMS-N 3 ), robust and highly conductive electrode passivation layers are formed in situ on the surface of both the Li 0 anode and the SPAN cathode. The resulting highly reversible, dendrite-free, and high-density Li 0 plating morphology enables a high Coulombic efficiency of 99.4%. Advanced tender energy X-ray spectroscopy also reveals the eliminated Li 2 S formation and minimized polysulfide dissolution in SPAN cathodes, leading to a high capacity of 580 mAh/g SPAN and stable cycling with negligible capacity decay (0.7%) for 800 cycles. This electrode–electrolyte interphase engineering strategy has tackled the major limitations of Li–S batteries in both ether- and carbonate-based electrolyte systems and under a wide temperature range from –10 to +50 °C, thus providing insightful guidelines for the rational design of highly durable and high-energy-density Li 0 -S batteries.

25 ENERGY STORAGE↗