Engineering Papers⌕ Search

Engineering topics

Walitt, L.

Publications and source records attributed to Walitt, L..

10 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

Calculation of the 3-D viscous flow at the endwall leading edge region of an axial annular turbine cascade

A three-dimensional viscous computer code (VANS/MD) was employed to calculate the turbulent flow field at the end wall leading edge region of a 20 inch axial annular turbine cascade. The initial boundary layer roll-up and formation of the end wall vortices were computed at the vane leading edge. The calculated flow field was found to be periodic with a frequency of approximately 1600 Hz. The calculated size of the separation region for the hub endwall vortex compared favorably with measured endwall oil traces. In an effort to determine the effects of the turbulence model on the calculated unsteadiness, a laminar calculation was made. The periodic nature of the calculated flow field persisted with the frequency essentially unchanged.

Walitt, L.↗
NASA NTRS1982

Development of a locally mass flux conservative computer code for calculating 3-D viscous flow in turbomachines

The VANS successive approximation numerical method was extended to the computation of three dimensional, viscous, transonic flows in turbomachines. A cross-sectional computer code, which conserves mass flux at each point of the cross-sectional surface of computation was developed. In the VANS numerical method, the cross-sectional computation follows a blade-to-blade calculation. Numerical calculations were made for an axial annular turbine cascade and a transonic, centrifugal impeller with splitter vanes. The subsonic turbine cascade computation was generated in blade-to-blade surface to evaluate the accuracy of the blade-to-blade mode of marching. Calculated blade pressures at the hub, mid, and tip radii of the cascade agreed with corresponding measurements. The transonic impeller computation was conducted to test the newly developed locally mass flux conservative cross-sectional computer code. Both blade-to-blade and cross sectional modes of calculation were implemented for this problem. A triplet point shock structure was computed in the inducer region of the impeller. In addition, time-averaged shroud static pressures generally agreed with measured shroud pressures. It is concluded that the blade-to-blade computation produces a useful engineering flow field in regions of subsonic relative flow; and cross-sectional computation, with a locally mass flux conservative continuity equation, is required to compute the shock waves in regions of supersonic relative flow.

Walitt, L.↗
NASA NTRS1977

Computation of viscous transonic flow about a lifting airfoil

The Reynolds averaged Navier-Stokes equations are solved numerically for the viscous transonic flow about a stationary NACA 64A010 airfoil in free air. This paper presents descriptions of the numerical method, turbulence models employed, and boundary conditions appropriate to simulation of free-air flight. Computed results are presented for the airfoil at a free-stream Mach number of 0.8, angles of attack of 0 and 2 deg, and a Reynolds number based on a chord of 4 x 10 to the 6th. For the lifting case, unsteady periodic motion was calculated along the aft portion of the airfoil and in its wake. Recent experimental results obtained by Johnson indicate periodicity aft of the shock closely approximates the computed frequency, but the amplitude of the disturbances was significantly less than the calculated amplitude.

Walitt, L.↗
NASA NTRS1976

Computation of viscous transonic flow about a lifting airfoil

The viscous transonic flow about a stationary body in free air was numerically investigated. The geometry chosen was a symmetric NACA 64A010 airfoil at a freestream Mach number of 0.8, a Reynolds number of 4 million based on chord, and angles of attack of 0 and 2 degrees. These conditions were such that, at 2 degrees incidence unsteady periodic motion was calculated along the aft portion of the airfoil and in its wake. Although no unsteady measurements were made for the NACA 64A010 airfoil at these flow conditions, interpolated steady measurements of lift, drag, and surface static pressures compared favorably with corresponding computed time-averaged lift, drag, and surface static pressures.

Walitt, L.↗
NASA NTRS1975

Numerical calculation of the internal flow field in a centrifugal compressor impeller

An iterative numerical method has been developed for the calculation of steady, three-dimensional, viscous, compressible flow fields in centrifugal compressor impellers. The computer code, which embodies the method, solves the steady three dimensional, compressible Navier-Stokes equations in rotating, curvilinear coordinates. The solution takes place on blade-to-blade surfaces of revolution which move from the hub to the shroud during each iteration.

Walitt, L.↗
NASA NTRS1974

Computation of steady axisymmetric flow using a one-dimensional time-dependent method

An iterative numerical method for computing steady, three dimensional, viscous, compressible flow fields, about aerodynamic bodies was studied. In order to develop the iterative method economically, the primary emphasis was directed towards supersonic, axisymmetric flow. However, the technique readily extends to three spatial dimensions. The viscous flow field about a cone-cylinder-flare body was calculated and compared to existing experimental data. Numerical predictions of the cone boundary layer and the flow field shock wave structure agreed with corresponding measurements. A separation was calculated at the cylinder-flare junction in six iterations; however, the size of the vortex did not correspond to the measured size. It was estimated that fifty iterations would be required to properly define the vortex. It was concluded that the iteration technique is of limited value for plane two dimensional and axisymmetrix flows, but of great value for three-dimensional flows.

Walitt, L.↗
NASA NTRS1971

A numerical method for computing three dimensional viscous supersonic flow fields about slender bodies

A numerical method is presented for the calculation of steady, three-dimensional, viscous, compressible flow fields about slender bodies at angle of attack and at supersonic speeds. Approximations are introduced in modeling the flow in the longitudinal direction. Accordingly, the flow fields calculated with the program were computed with a model that permits viscous crossflow together with inviscid axial flow. An analysis of the errors introduced by such a treatment is presented. Numerical calculations were made and compared with experimental results for an ogive-cylinder and an airplane fuselage configuration. Generally, good agreement with experiment was obtained. However, boundary layer separation and body vortex positions differed from experimental locations on the ogive-cylinder, and the shock induced by the fuselage canopy was predicted at a slightly different location.

Walitt, L.↗