Engineering topics

Wagner, Timothy C.

Publications and source records attributed to Wagner, Timothy C..

4 records

NASA NTRS1989

Plasma torch igniter for scramjets

A small, uncooled plasma torch was developed and used in combination with an injector designed to study ignition and flameholding in hydrogen-fueled supersonic flows. The plasma torch was operated on mixtures of hydrogen and argon with total flows of 10 to 70 scfh. The fuel injector design consisted of five small upstream pilot fuel injectors, a rearward facing step for recirculation, and three main fuel injectors downstream of the step. The plasma torch was located in the recirculation region, and all injection was perpendicular to the Mach 2 stream. Both semi-freejet and ducted tests were conducted. The experimental results indicate that a low power plasma torch operating on a 1:1 volumetric mixture of hydrogen and argon and located in the recirculation zone fueled by the upstream pilot fuel injectors is a good igniter for flow conditions simulating a flight Mach number of 3.7. The total temperature required to autoignite the hydrogen fuel for this injector geometry was 2640 R. The injector configuration was shown to be a good flameholder over a wide range of total temperature. Spectroscopic measurements were used to verify the presence of air total temperatures below 1610 R.

Wagner, Timothy C.↗

NASA NTRS1987

Design and evaluation of a new injector configuration for supersonic combustion

Ignition and flameholding behavior data are presented from experiments with a novel scramjet injector configuration consisting of five small upstream pilot fuel injectors, a rearward-facing step, and three primary fuel injectors downstream of the step; all injection is perpendicular to the Mach 2 airflow, and the ignition source is located in the recirculation region downstream of the step. The design attempts to minimize the amount of igniter energy required for ignition, but without introduction of the large losses associated with bluff bodies. Argon plasma, argon-hydrogen plasma, pyrophoric silane/hydrogen, and surface-discharge ignition sources are tested. The injector is found to be able to hold flames at 1400 R total temperatures without the use of large bluff bodies; the argon-hydrogen plasma was the most effective igniter.

Wagner, Timothy C.↗

NASA NTRS1986

Plasma torch igniter for scramjets

A small, uncooled plasma torch was developed and used in combination with an injector designed to study ignition and flameholding in hydrogen-fueled supersonic flows. The plasma torch was operated on mixtures of hydrogen and argon with total flows of 10 to 70 scfh. The fuel injector design consisted of five small upstream pilot fuel injectors, a rearward facing step for recirculation, and three main fuel injectors downstream of the step. The plasma torch was located in the recirculation region, and all injection was perpendicular to the Mach 2 stream. Both semi-freejet and ducted tests were conducted. The experimental results indicate that a low power plasma torch operating on a 1:1 volumetric mixture of hygrogen and argon and located in the recirculation zone fueled by the upstream pilot fuel injectors is a good igniter for flow conditions simulating a flight Mach number of 3.7. The total temperature required to autoignite the hydrogen fuel for this injector geometry was 2640 R. The injector configuration was shown to be a good flameholder over a wide range of total temperature. Spectroscopic measurements were used to verify the presence of air total temperatures below 1610 R.

Wagner, Timothy C.↗

NASA NTRS1986

Development and evaluation of a 1 kW plasma torch ignitor for scramjets

A low power, uncooled plasma torch was tested in combination with a new injector design to study ignition and flameholding in hydrogen-fueled supersonic flows. Both semifree jet and ducted tests were conducted in a Mach 2 flow under simulated scramjet combustor conditions at 1 atmosphere static pressure and total temperatures between 1400 and 2800 R. The injector design incorporates a small upstream pilot fuel flow, a step for recirculation, and primary fuel injectors downstream of the recirculation region. Using a 1:1 volumetric mixture of hydrogen and argon, good performance at a simulated flight Mach number of 3.7 is found for a 1-kW torch which is located in the recirculation zone and fueled by the upstream pilot fuel injectors. Spectroscopic measurements verified the presence of hydrogen atoms in the torch exhaust, and it is suggested that hydrogen atoms are responsible for the ignition.

Wagner, Timothy C.↗