Engineering topics

Voss, Lars F.

Publications and source records attributed to Voss, Lars F..

8 records

DOE OSTI2024

Photoluminescence and Raman spectroscopy of wide bandgap semiconductors damaged by deep-UV laser irradiation

The effects of a pulsed, focused, deep-UV (4.66 eV) laser on wide and ultra-wide bandgap semiconductors were investigated with photoluminescence (PL) and Raman spectroscopy. Three semiconductor single crystals were studied: silicon carbide (6H-SiC), gallium nitride (GaN), and gallium oxide (β-Ga 2 O 3 ). Atomic emission lines from neutral Ga or Si were observed during the laser-damage process. For all three semiconductors, PL mapping (3.49 eV laser excitation) of the damaged material revealed visible emission bands in the 2.6–2.8 eV range, attributed to point defects. Raman spectra (2.33 eV excitation) showed a reduction in the Raman peak intensities in the damaged region, along with weak PL bands around 1.9–2.1 eV.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Growth Phenomena and Bandgap Shift in Melt-Grown β-(In x Ga 1- x ) 2 O 3 Alloys

β-Ga 2 O 3 is an emerging ultra-wide bandgap semiconductor with great promise for power electronics and optoelectronics. Alloys in the In 2 O 3 -Ga 2 O 3 system are interesting for optoelectronic applications, particularly where bandgap tuning is desirable. Herein, β-(In x Ga 1- x ) 2 O 3 alloys with target compositions x = 0.025 or 0.10 are grown from the melt using the Czochralski and vertical gradient freeze techniques. Growth with 10 mol% In yields only small, needle-like crystals, while 2.5 mol% In allows growth of centimeter-sized single crystals. A substantial degree of indium segregation is unveiled by spatial measurements of lattice parameters and the bandgap. The bandgap decreases by a maximum of 0.28 eV in the case of the highest In content crystals. Z-contrast transmission electron microscopy confirms a solely octahedral coordination of In in the β-Ga 2 O 3 lattice. With indium concentrations higher than 2.5 mol%, samples contain micron-scale voids that impart a dark coloration. All measured crystals are electrically conductive, with carrier concentrations varying 10 16 –10 17 cm -3 depending upon the location of the sample in the growth. Lastly, a unique luminescence with unknown origin centered around 2.0 eV is revealed by photoluminescence spectroscopy.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Enhanced Laser Damage Threshold in Optically Addressable Light Valves via Aluminum Nitride Photoconductors

Abstract Optically addressable light valves (OALVs) are specialized optical components utilized for spatial beam shaping in various laser‐based applications, including optics damage mitigation, and enhanced functionality in diode‐based additive manufacturing requiring high intensities. Current state‐of‐the‐art OALVs employ photoconductors such as Bismuth Silicon Oxide (BSO) or Bismuth Germanium Oxide (BGO), which suffer from limited laser‐induced damage thresholds (LiDT) and inadequate thermal conductivities, thus restricting their use in high peak and average power applications. Aluminum nitride (AlN), an emerging ultra‐wide band gap (UWBG) III–V semiconductor, offers promising optoelectronic properties and superior thermal conductivity (>300 Wm −1 K −1 at 298° K, compared to BSO's 3.29 Wm −1 K −1 ). In this study, the first AlN‐based OALVs are designed, fabricated, and experimentally demonstrated using commercially available single‐crystal AlN substrates. These AlN‐based OALVs have shown clear superiority over BSO and BGO‐based devices. Design considerations for OALVs incorporating UWBG photoconductors are discussed, and the photoresponsivity from defect‐mediated sub‐bandgap absorption in AlN crystals is verified as sufficient for OALVs operating under high light fluences. The optimum driving voltage for the AlN‐based OALV is determined to be ≈ 45 V pp at 100 Hz, achieving a transmittance of 91.3%, an extinction ratio (ER) of more than 100, and a 51:1 image contrast.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Wide bandgap optical switch circuit breaker for controlling propagation of current therethrough a wide bandgap optical device

A high-voltage switch is adapted for use as a medium-voltage direct current circuit breaker, which provides a low-cost, small-footprint device to mitigate system faults. In one example, a method for operating a wideband optical device includes illuminating the wide bandgap optical device with a light within a first range of wavelengths and a first average intensity, allowing a current to propagate therethrough without substantial absorption of the current, illuminating the wide bandgap optical device with light within the first range of wavelengths and a second average intensity that is lower than the first average intensity to allow a sustained current flow though the wide bandgap optical device, and illuminating the wide bandgap optical device with light within a second range of wavelengths to stop or substantially restrict propagation of the current through the wide gap material.

Voss, Lars F.↗

DOE OSTI2024

Photoluminescence mapping of laser-damaged β-Ga 2 O 3

Here, photoluminescence (PL) mapping was utilized to investigate damage in β-Ga 2 O 3 epilayers induced by 1064 nm laser pulses. The intensity and position of the intrinsic UV band were determined and plotted as a false-color image. Two types of damage were identified: circular damage and damage cracks. Circular damage shows lower UV PL intensity than the surrounding material with color centers in a “halo” around the damaged region. Damage cracks are aligned with the a and c axes and show higher PL intensity than undamaged material. Defects in the as-grown material were revealed by shifts in the UV band energy.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Simulating charged defects at database scale

Point defects have a strong influence on the physical properties of materials, often dominating the electronic and optical behavior in semiconductors and insulators. The simulation and analysis of point defects is, therefore, crucial for understanding the growth and operation of materials, especially for optoelectronics applications. In this work, we present a general-purpose Python framework for the analysis of point defects in crystalline materials as well as a generalized workflow for their treatment with high-throughput simulations. The distinguishing feature of our approach is an emphasis on a unique, unit cell, structure-only, definition of point defects which decouples the defect definition, and the specific supercell representation used to simulate the defect. This allows the results of first-principles calculations to be aggregated into a database without extensive provenance information and is a crucial step in building a persistent database of point defects that can grow over time, a key component toward realizing the idea of a “defect genome” that can yield more complex relationships governing the behavior of defects in materials. We demonstrate several examples of the approach for three technologically relevant materials and highlight current pitfalls that must be considered when employing these methodologies as well as their potential solutions.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Melt-grown semi-insulating Mn:β-Ga 2 O 3 single crystals exhibiting unique visible absorptions and luminescence

In this study, several acceptor dopants have been explored in β-Ga 2 O 3 to produce semi-insulating substrates and epitaxial films. Fe and Mg make up the majority of research thus far; however, other transition metals provide potential alternatives for optimized performance. β-Ga 2 O 3 bulk single crystals were grown by the Czochralski and vertical gradient freeze methods with a nominal dopant concentration of 0.25 at. % Mn. Ultraviolet-visible-near infrared spectroscopy and photoluminescence revealed polarization- and orientation-dependent optical absorptions (pleochroism) coupled with an orange luminescence. All samples were electrically insulating, on the order of 10 9 –10 11 ohm cm at room temperature, indicative of acceptor doping. Actual dopant concentrations of the intentionally doped transition metal and background impurities were determined via glow discharge mass spectrometry, indicating the macroscale segregation behavior. High-temperature resistivity measurements indicated an experimental acceptor level of 1.7 ± 0.2 eV. Hydrogenation of samples resulted in an increase in the orange luminescence and O–H stretching modes observable in the infrared spectrum. Density functional theory calculations were performed to determine the likely site-occupancy and acceptor level of Mn in the bandgap.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Pulse compression photoconductive semiconductor switches

A photoconductive switch that uses materials that support negative differential mobility, whose operation leverages the pulse compression of a charge could to generate the “on” time of the pulse in combination with the speed of light to generate the “off” time of the pulse, is described. In one example, a method of operating a photoconductive switch, which includes two electrodes and a light absorbing material positioned therebetween, includes selecting a value for one or more parameters comprising a voltage for generation of an electric field, a spot size of a laser pulse, a temporal pulse width of the laser pulse, or an intensity of the laser pulse, wherein the selected value(s) for the one or more parameters enable the switch to operate in a region where the light absorbing material exhibits negative differential mobility, and illuminating the light absorbing material with the laser pulse to generate a charge cloud within the light absorbing material.

Voss, Lars F.↗