Engineering Papers⌕ Search

Engineering topics

Vijgen, P. M. H. W.

Publications and source records attributed to Vijgen, P. M. H. W..

17 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

Leading-edge transition and relaminarization phenomena on a subsonic high-lift system

Boundary-layer transition and relaminarization may have a critical effect on the flow development about multielement high-lift systems of subsonic transport aircraft with swept wings. The purpose of this paper is a study of transition phenomena in the leading-edge region of the various elements of a high-lift system. The flow phenomena studied include transition of the attachment-line flow, relaminarization, and crossflow instability. The calculations are based on pressure distributions measured in flight on the NASA Transport Systems Research Vehicle (Boeing 737-100) at a wing station where the flow approximated infinite swept wing conditions. The results indicate that significant regions of laminar flow can exist on all flap elements in flight. In future flight experiments the extent of these regions will be measured, and the transition mechanisms and the effect of laminar flow on the high-lift characteristics of the multi-element system will be further explored.

Van Dam, C. P.↗
NASA NTRS1992

Prediction of drag at subsonic and transonic speeds using Euler methods

A technique for the evaluation of aerodynamic drag from flowfield solutions based on the Euler equations is discussed. The technique is limited to steady attached flows around three-dimensional configurations in the absence of active systems such as surface blowing/suction and propulsion. It allows the decomposition of the total drag into induced drag and wave drag and, consequently, it provides more information on the drag sources than the conventional surface-pressure integration technique. The induced drag is obtained from the integration of the kinetic energy (per unit distance) of the trailing vortex system on a wake plane and the wave drag is obtained from the integration of the entropy production on a plane just downstream of the shocks. The drag-evaluation technique is applied to three-dimensional flowfield solutions for the ONERA M6 wing as well as an aspect-ratio-7 wing with an elliptic spanwise chord distribution and an NACA-0012 section shape. Comparisons between the drag obtained with the present technique and the drag based on the integration of surface pressures are presented for two Euler codes.

Nikfetrat, K.↗
NASA NTRS1992

Flow prediction over a transport multi-element high-lift system and comparison with flight measurements

Accurate prediction of surface-pressure distributions, merging boundary-layers, and separated-flow regions over multi-element high-lift airfoils is required to design advanced high-lift systems for efficient subsonic transport aircraft. The availability of detailed measurements of pressure distributions and both averaged and time-dependent boundary-layer flow parameters at flight Reynolds numbers is critical to evaluate computational methods and to model the turbulence structure for closure of the flow equations. Several detailed wind-tunnel measurements at subscale Reynolds numbers were conducted to obtain detailed flow information including the Reynolds-stress component. As part of a subsonic-transport high-lift research program, flight experiments are conducted using the NASA-Langley B737-100 research aircraft to obtain detailed flow characteristics for support of computational and wind-tunnel efforts. Planned flight measurements include pressure distributions at several spanwise locations, boundary-layer transition and separation locations, surface skin friction, as well as boundary-layer profiles and Reynolds stresses in adverse pressure-gradient flow.

Vijgen, P. M. H. W.↗
NASA NTRS1991

Drag calculations of wings using Euler methods

Several techniques for the calculation of drag using Euler-equation formulations are discussed and compared. Surface-pressure integration (a nearfield technique) as well as two different farfield calculation techniques are described and applied to three-dimensional flow-field solutions for an aspect-ratio-7 wing with attached flow. The present calculations are limited to steady, low-Mach-number flows around three-dimensional configurations in the absence of active systems such as surface blowing/suction and propulsion. Although the main focus of the paper is the calculation of aerodynamic drag, the calculation of aerodynamic lift is also briefly discussed. Three Euler methods are used to obtain the flowfield solutions. The farfield technique based on the evaluation of a wake-integral appears to provide the most consistent and accurate drag predictions.

Van Dam, C. P.↗
NASA NTRS1990

Parametric analysis of swept-wing geometry with sheared wing tips

A computational parameter study is presented of potential reductions in induced drag and increases in lateral-directional stability due to sheared wing tips attached to an untwisted wing of moderate sweep and aspect ratio. Sheared tips are swept and tapered wing-tip devices mounted in the plane of the wing. The induced-drag results are obtained using an inviscid, incompressible surface-panel method that models the nonlinear effects due to the deflected and rolled-up wake behind the lifting surface. The induced-drag results with planar sheared tips are compared to straight-tapered tip extensions and nonplanar winglet geometries. The lateral-directional static-stability characteristics of the wing with sheared tips are estimated using a quasi-vortex-lattice method. For certain combinations of sheared-tip sweep and taper, both the induced efficiency of the wing and the relevant static-stability derivatives are predicted to increase compared to the wing with a straight-tapered tip modification.

Fremaux, C. M.↗
NASA NTRS1990

Wind-tunnel investigation on the effect of a crescent planform on drag

Lift and drag forces were compared for elliptic and crescent wing models at cruise and climb conditions in the NASA/Langley 14 x 22-ft subsonic tunnel. The force measurements were obtained for an angle-of-attack range from -3 to 10 deg at a Reynolds number of about 1.7 million. The results indicate that for attached flow conditions, the crescent wing with its highly swept tips generates less lift-dependent drag than the elliptic wing for given lift force, wing span, and freestream conditions. The drag reduction is thought to be the result of the favorable influence of trailing wake deformations on the pressure distribution of the highly swept outboard region of the crescent wing.

Van Dam, C. P.↗
NASA NTRS1989

Wind-tunnel investigations of wings with serrated sharp trailing edges

Exploratory wind-tunnel force measurements are presented for two wing geometries with small-scale planar and nonplanar serrated trailing-edge devices (chord-Reynolds numbers ranged from 1.0 to 3.7 million). The planar serrated trailing-edge extensions reduced the drag at conditions when trailing-edge separation occurred at low angles of attack. The introduction of serrations reduced or eliminated the drag penalty, due to the small (1-2 percent of the chord length) nonplanar trailing-edge flaps, while maintaining the effects of increase in camber. The presence of streamwise vortices immediately downstream of the serrated trailing edges is believed to have favorably affected the boundary-layer flow approaching the trailing edge and the near-wake development, resulting in reduced pressure (form) drag.

Vijgen, P. M. H. W.↗
NASA NTRS1989

Sheared wing-tip aerodynamics - Wind-tunnel and computational investigation

Computational and experimental performance benefits are presented for a high-aspect-ratio unswept wing configuration with sheared tips. The sheared tip is a highly swept and highly tapered surface located in the same plane as the inboard wing panel to which it is attached. The compuational results were obtained with an inviscid surface panel method that models the nonlinear influence of the trailing wake. Both wind-tunnel and calculated results were obtained for a 12-ft span wing model with various wing-tip configurations. The computational and experimental data are in fair agreement and demonstrate that sheared wing tips can reduce induced drag at cruise and climb lift coefficients. The drag reduction is the result of wake deformation effects and changes in spanwise load distribution. Wind-tunnel measured longitudinal and lateral directional stability characteristics are also presented for the various wing-tip layouts.

Vijgen, P. M. H. W.↗
NASA NTRS1989

High-alpha aerodynamic characteristics of crescent and elliptic wings

Static longitudinal and lateral-directional forces and moments were measured for elliptic- and crescent-wing models at high angles of attack in the NASA Langley 14-by-22-ft Subsonic Tunnel. The forces and moments were obtained for an angle-of-attack range including stall and post-stall conditions at a Reynolds number based on the average wing chord of about 1.8 million. Flow-visualization photographs using a mixture of oil and titanium-dioxide were also taken for several incidence angles. The force and moment data and the flow-visualization results indicated that the crescent wing model with its highly swept tips produced much better high-angle-of-attack aerodynamic characteristics than the elliptic model. Leading-edge separation-induced vortex flow over the highly swept tips of the crescent wing is thought to produce this improved behavior at high angles of attack. The unique planform design could result in safer and more efficient low-speed airplanes.

Van Dam, C. P.↗
NASA NTRS1989

Wind-tunnel investigations of wings with serrated sharp trailing edges

Exploratory wind-tunnel force measurements are presented for two wing geometries with small-scale planar and nonplanar serrated trailing-edge devices (chord-Reynolds numbers ranged from 1.0 - 3.7 x 10 to the 6th). The planar serrated trailing-edge extensions reduced the drag at conditions when trailing-edge separation occurred at low angles of attack. The introduction of serrations reduced or eliminated the drag penalty due to the small (1-2 percent of the chord length) nonplanar trailing-edge flaps, while maintaining the effects of increase in camber. The presence of streamwise vortices immediately downstream of the serrated trailing edges is believed to have favorably affected the boundary-layer flow approaching the trailing edge and the near-wake development, resulting in reduced pressure drag.

Vijgen, P. M. H. W.↗
NASA NTRS1988

Effects of compressibility on design of subsonic fuselages for natural laminar flow

Compressible linear boundary-layer stability analyses of two representative axisymmetric fuselage geometries indicate that a favorable effect will be exerted on the characteristics of a fuselage's axisymmetric boundary layer by compressibility. A freestream Mach number increase from 0.6 to 0.8 significantly reduces TS wave growth rates in the laminar boundary layer of the fuselages analyzed. The generally destabilizing effect of increasing length Re number on boundary layer stability can be overpowered by the favorable effects of compressibility on the fluid.

Vijgen, P. M. H. W.↗
NASA NTRS1988

Analysis of wind-tunnel boundary-layer transition experiments on axisymmetric bodies at transonic speeds using compressible boundary-layer stability theory

The design of laminar flow fuselages and advanced swept wings at high-subsonic compressible speeds can benefit from a correlation of compressible transition experiments with the e exp n transition-prediction method. A computational analysis has been conducted to investigate the detailed transition measurements obtained by Boltz et al. (1956, 1960) for two bodies-of-revolution. Nonadiabatic wall conditions were included in the analysis when wall-temperature measurements were available.

Vijgen, P. M. H. W.↗
NASA NTRS1986

Design of fuselage shapes for natural laminar flow

Recent technological advances in airplane construction techniques and materials allow for the production of aerodynamic surfaces without significant waviness and roughness, permitting long runs of natural laminar flow (NLF). The present research effort seeks to refine and validate computational design tools for use in the design of axisymmetric and nonaxisymmetric natural-laminar-flow bodies. The principal task of the investigation involves fuselage body shaping using a computational design procedure. Analytical methods were refined and exploratory calculations conducted to predict laminar boundary-layer on selected body shapes. Using a low-order surface-singularity aerodynamic analysis program, pressure distribution, boundary-layer development, transition location and drag coefficient have been obtained for a number of body shapes including a representative business-aircraft fuselage. Extensive runs of laminar flow were predicted in regions of favorable pressure gradient on smooth body surfaces. A computational design procedure was developed to obtain a body shape with minimum drag having large extent of NLF.

Dodbele, S. S.↗
NASA NTRS1986

Shaping of airplane fuselages for minimum drag

The VSAERO surface panel method is employed to investigate fuselage shapes which can enhance the natural laminar flow (NLF) characteristics. The study is performed at cruise Re which are relevant to commuter, transport, and business aircraft. The technique is based on piecewise constant doublet and source singularities and takes into account the effects of compressibility. Inviscid pressure distributions were generated for five configurations to aid in the search for an optimized NLF body shape as a function of the transition locations and the drag coefficients. Granville's transition criteria are incorporated into the calculations to yield shapes with longer runs of laminar flow and reduced drag. In comparison with other transition prediction methods, the method described is shown to have significantly higher valicity for making three-dimensional transition predictions.

Dodbele, S. S.↗