Engineering Papers⌕ Search

Engineering topics

Vicroy, Dan D.

Publications and source records attributed to Vicroy, Dan D..

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS2000

Model Validation of Wake-Vortex/Aircraft Encounters

Wake-vortex effects on an 10% scale model of the B737-100 aircraft are calculated using both strip theory and vortex-lattice methods. The results are then compared to data taken in the 30ft x 60ft wind tunnel at NASA Langley Research Center (LaRC). The accuracy of the models for a reduced geometry, such with the horizontal stabilizer and the vertical tail removed, is also investigated. Using a 10% error in the circulation strength and comparing the model's results with the experiment illustrates the sensitivity of the models to the vortex circulation strength. It was determined that both strip theory and the vortex lattice method give accurate results when all the geometrical information is used. When the horizontal stabilizer and vertical tail were removed there were difficulties modeling the sideforce coefficient and pitching moment. With the removal of only the vertical tail unacceptable errors occurred when modeling the sideforce coefficient and yawing moment. Lift could not be accurately modeled with either the full geometry or the reduced geometry.

Pete, Kimberly R.↗
NASA NTRS1999

Flight Data Reduction of Wake Velocity Measurements Using an Instrumented OV-10 Airplane

A series of flight tests to measure the wake of a Lockheed C- 130 airplane and the accompanying atmospheric state have been conducted. A specially instrumented North American Rockwell OV-10 airplane was used to measure the wake and atmospheric conditions. An integrated database has been compiled for wake characterization and validation of wake vortex computational models. This paper describes the wake- measurement flight-data reduction process.

Vicroy, Dan D.↗
NASA NTRS1998

Characterizing the Hazard of a Wake Vortex Encounter

The National Aeronautics and Space Administration (NASA) is conducting research with the goal of enabling safe improvements in the capacity of the nation's air transportation system. The wake vortex upset hazard is an important factor in establishing the minimum safe spacing between aircraft during landing and take-off operations, thus impacting airport capacity. Static and free-flight wind tunnel tests and flight tests have provided an extensive data set for improved understanding of vortex encounter dynamics and simulation. Piloted and batch simulation studies are also ongoing to establish a first-order hazard metric and determine the limits of an operationally acceptable wake induced upset. This paper outlines NASA's research in these areas.

Vicroy, Dan D.↗
NASA NTRS1998

Recent NASA Wake-Vortex Flight Tests, Flow-Physics Database and Wake-Development Analysis

A series of flight tests over the ocean of a four engine turboprop airplane in the cruise configuration have provided a data set for improved understanding of wake vortex physics and atmospheric interaction. An integrated database has been compiled for wake characterization and validation of wake-vortex computational models. This paper describes the wake-vortex flight tests, the data processing, the database development and access, and results obtained from preliminary wake-characterization analysis using the data sets.

Vicroy, Dan D.↗
NASA NTRS1996

A preliminary study of a wake vortex encounter hazard boundary for a B737-100 airplane

A preliminary batch simulation study was conducted to define the wake decay required for a Boeing 737-100 airplane to safely encounter a Boeing 727 wake and land. The baseline six-degree-of-freedom B737 simulation was modified to include a wake model and the strip-theory calculation of the vortex-induced forces and moments. The guidance and control inputs for the airplane were provided by an autoland system. The wake strength and encounter altitude were varied to establish a safe encounter boundary. The wake was positioned such that the desired flight path traversed the core of the port Vortex. Various safe landing criteria were evaluated for defining a safe encounter boundary. A sensitivity study was also conducted to assess the effects of encounter model inaccuracies.

Reimer, Heidi M.↗
NASA NTRS1994

Microburst vertical wind estimation from horizontal wind measurements

The vertical wind or downdraft component of a microburst-generated wind shear can significantly degrade airplane performance. Doppler radar and lidar are two sensor technologies being tested to provide flight crews with early warning of the presence of hazardous wind shear. An inherent limitation of Doppler-based sensors is the inability to measure velocities perpendicular to the line of sight, which results in an underestimate of the total wind shear hazard. One solution to the line-of-sight limitation is to use a vertical wind model to estimate the vertical component from the horizontal wind measurement. The objective of this study was to assess the ability of simple vertical wind models to improve the hazard prediction capability of an airborne Doppler sensor in a realistic microburst environment. Both simulation and flight test measurements were used to test the vertical wind models. The results indicate that in the altitude region of interest (at or below 300 m), the simple vertical wind models improved the hazard estimate. The radar simulation study showed that the magnitude of the performance improvement was altitude dependent. The altitude of maximum performance improvement occurred at about 300 m.

Vicroy, Dan D.↗
NASA NTRS1994

Vertical wind estimation from horizontal wind measurements

The objective of this study was to assess the ability of simple vertical wind models to improve the hazard prediction capability of an airborne Doppler sensor in a realistic microburst environment. The results indicate that in the altitude region of interest (at or below 300 meters), both the linear and empirical vertical wind models improved the hazard estimate. The radar simulation study showed that the magnitude of the performance improvement was altitude dependent. The altitude of maximum performance improvement occurred at about 300 meters. At the lower altitudes the percent improvement was minimized by the diminished contribution of the vertical wind. The vertical hazard estimate errors from flight tests were less than those of the radar simulation study.

Vicroy, Dan D.↗
NASA NTRS1993

The challenges of simulating wake vortex encounters and assessing separation criteria

During landings and take-offs, the longitudinal spacing between airplanes is in part determined by the safe separation required to avoid the trailing vortex wake of the preceding aircraft. Safe exploration of the feasibility of reducing longitudinal separation standards will require use of aircraft simulators. This paper discusses the approaches to vortex modeling, methods for modeling the aircraft/vortex interaction, some of the previous attempts of defining vortex hazard criteria, and current understanding of the development of vortex hazard criteria.

Dunham, R. E.↗
NASA NTRS1993

NASA wake vortex research

NASA is conducting research that will enable safe improvements in the capacity of the nation's air transportation system. The wake-vortex hazard is a factor in establishing the minimum safe spacing between aircraft during landing and takeoff operations and, thus, impacts airport capacity. The ability to accurately model the wake hazard and determine safe separation distances for a wide range of aircraft and operational scenarios may provide the basis for significant increases in airport capacity. Current and planned NASA research is described which is focused on increasing airport capacity by safely reducing wake-hazard-imposed aircraft separations through advances in a number of technologies including vortex motion and decay prediction, vortex encounter modeling, wake-vortex hazard characterization, and in situ flow sensing.

Stough, H. P., III↗
NASA NTRS1993

A Numerical Simulation Study to Develop an Acceptable Wake Encounter Boundary for a B737-100 Airplane

The National Aeronautics and Space Administration (NASA) is conducting research with the goal of enabling safe improvements in the capacity of the nation's air transportation system. The wake-vortex upset hazard is an important factor in establishing the minimum safe spacing between aircraft during landing and take-off operations, thus impacting airport capacity. A batch simulation study was conducted to assess the sensitivity of various safe landing criteria in the development of an acceptable wake encounter boundary. A baseline six-degree-of-freedom simulation of a B737-100 airplane was modified to include a wake model and the vortex-induced forces and moments. The guidance and control input for the airplane was provided by an auto-land system. The wake strength and encounter geometry were varied. A sensitivity study was also conducted to assess the effects of encounter modeling methods and accuracy.

Vicroy, Dan D.↗
NASA NTRS1992

Airborne Wind Shear Detection and Warning Systems. Fourth Combined Manufacturers' and Technologists' Conference, part 2

The Fourth Combined Manufacturers' and Technologists' Conference was hosted jointly by NASA Langley Research Center (LaRC) and the Federal Aviation Administration (FAA) in Williamsburg, Virginia, on April 14-16, 1992. The meeting was co-chaired by Dr. Roland Bowles of LaRC and Bob Passman of the FAA. The purpose of the meeting was to transfer significant ongoing results of the NASA/FAA Joint Airborne Wind Shear Program to the technical industry and to pose problems of current concern to the combined group. It also provided a forum for manufacturers to review forward-look technology concepts and for technologists to gain an understanding of the problems encountered by the manufacturers during the development of airborne equipment and the FAA certification requirements. The present document has been compiled to record the essence of the technology updates and discussions which follow each.

Vicroy, Dan D.↗
NASA NTRS1992

Airborne Wind Shear Detection and Warning Systems: Fourth Combined Manufacturers' and Technologists' Conference, part 1

The purpose of the meeting was to transfer significant ongoing results of the NASA/FAA joint Airborne Wind Shear Program to the technical industry and to pose problems of current concern to the combined group. It also provided a forum for manufacturers to review forward-look technology concepts and for technologists to gain an understanding of the problems encountered by the manufacturers during the development of airborne equipment and the FAA certification requirements. The present document was compiled to record the essence of the technology updates and discussions which follow each.

Vicroy, Dan D.↗
NASA NTRS1992

Vertical wind estimation from horizontal wind measurements

This presentation begins with a brief description of the downdraft measurement problem for airborne Doppler based systems and the importance of the downdraft in assessing the hazard posed by a microburst wind shear. This is followed by a review of research on the feasibility of using simple microburst models to compute the downdraft from horizontal wind measurements. The current methodologies for computing the vertical wind are then discussed. A summary of the results and the plan for future research are also presented.

Vicroy, Dan D.↗
NASA NTRS1991

A simple, analytical, axisymmetric microburst model for downdraft estimation

A simple analytical microburst model was developed for use in estimating vertical winds from horizontal wind measurements. It is an axisymmetric, steady state model that uses shaping functions to satisfy the mass continuity equation and simulate boundary layer effects. The model is defined through four model variables: the radius and altitude of the maximum horizontal wind, a shaping function variable, and a scale factor. The model closely agrees with a high fidelity analytical model and measured data, particularily in the radial direction and at lower altitudes. At higher altitudes, the model tends to overestimate the wind magnitude relative to the measured data.

Vicroy, Dan D.↗
NASA NTRS1991

Airborne Wind Shear Detection and Warning Systems: Third Combined Manufacturers' and Technologists' Conference, part 2

The Third Combined Manufacturers' and Technologists' Conference was held in Hampton, Va., on October 16-18, 1990. The purpose of the meeting was to transfer significant on-going results of the NASA/FAA joint Airborne Wind Shear Program to the technical industry and to pose problems of current concern to the combined group. It also provided a forum for manufacturers to review forward-look technology concepts and for technologists to gain an understanding of the problems encountered by the manufacturers during the development of airborne equipment and the FAA certification requirements.

Vicroy, Dan D.↗
NASA NTRS1991

Estimate of heavy rain performance effect

The aerodynamic effect of heavy rain on airplane performance is presented in the form of view-graphs. The following subject areas are covered: review of heavy rain airfoil tests; development of heavy rain aerodynamic model for a twin-jet transport; performance analysis with heavy rain effects; numeric simulation of wet microburst encounter; and summary of results and future needs.

Vicroy, Dan D.↗