Vento, D. M. | Engineering Papers

NASA NTRS1992

CONE - An STS-based cryogenic fluid management experiment

An overview of the CONE program is presented which includes a definition of the technology addressed by CONE and a baseline experiment set, a description of the experimental and support subsystems, interface requirements between the STS and the experiment carrier (Hitchhiker M), and the reusability and expansion capacity for additional experiment flights. CONE evaluates three primary technologies: the active thermodynamic vent system, the passive thermodynamic vent system, and liquid acquisition device performance. The cryogenic fluid management technology database that the system offers will allow for efficient subcritical cryogenic system designs for operation in a low-gravity environment. This system maximizes the balance between existing component technology and the need for the development of a cryogenic-fluid-management (CFM) test bed to investigate and demonstrate methods of storage and handling arenas.

Bell, R. S.↗

NASA NTRS1990

The COLD-SAT Experiment for Cryogenic Fluid Management Technology

Future national space transportation missions will depend on the use of cryogenic fluid management technology development needs for these missions. In-space testing will be conducted in order to show low gravity cryogenic fluid management concepts and to acquire a technical data base. Liquid H2 is the preferred test fluid due to its propellant use. The design of COLD-SAT (Cryogenic On-orbit Liquid Depot Storage, Acquisition, and Transfer Satellite), an Expendable Launch Vehicle (ELV) launched orbital spacecraft that will perform subcritical liquid H2 storage and transfer experiments under low gravity conditions is studied. An Atlas launch vehicle will place COLD-SAT into a circular orbit, and the 3-axis controlled spacecraft bus will provide electric power, experiment control, and data management, attitude control, and propulsive accelerations for the experiments. Low levels of acceleration will provide data on the effects that low gravity might have on the heat and mass transfer processes used. The experiment module will contain 3 liquid H2 tanks; fluid transfer, pressurization and venting equipment; and instrumentation.

Schuster, J. R.↗

NASA NTRS1990

The COLD-SAT experiment for cryogenic fluid management technology

The COLD-SAT spacecraft design experiments are described. COLD-SAT will be placed into an initial 1300 km circular orbit by an Atlas commercial launch vehicle. Electric power, experiment control and data management, attitude control, and propulsive accelarations for the experiments will be provided by the three-axis-controlled spacecraft bus. To provide data on the effects that low gravity levels might have on the heat and mass transfer processes involved, low levels of accelaration will be created. The COLD-SAT experiment will be configured into a module. The spacecraft experiment module will include three liquid hydrogen tanks; fluid transfer, pressurization and venting equipment; and instrumentation. Since the largest tank has helium-purged MLI to prevent ingress and freezing of air on the launchpad, it will contain all the liquid hydrogen at the point of launching. The hydrogen tanking system used for the Centaur upper stage of the Atlas will load and top off this tank. Atlas, with its liquid hydrogen upper stage, large payload fairing, and large launch margin, simplifies COLD-SAT design and integration.

Schuster, J. R.↗

NASA NTRS1989

The solid surface combustion space shuttle experiment hardware description and ground-based test results

The Lewis Research Center is developing a series of microgravity combustion experiments for the Space Shuttle. The Solid Surface Combustion Experiment (SSCE) is the first to be completed. SSCE will study flame spreading over thermally thin fuels (ashless filter paper) under microgravity conditions. The flight hardware consists of a combustion chamber containing the sample and a computer which takes the data and controls the experiment. Experimental data will include gas-phase and solid-phase temperature measurements and motion pictures of the combustion process. Flame spread rates will be determined from the motion pictures.

Vento, D. M.↗

NASA NTRS1989

The solid surface combustion Space Shuttle experiment hardware description and ground-based test results

The Lewis Research Center is developing a series of microgravity combustion experiments for the Space Shuttle. The Solid Surface Combustion Experiment (SSCE) is the first to be completed. SSCE will study flame spreading over thermally thin fuels (ashless filter paper) under microgravity conditions. The flight hardware consists of a combustion chamber containing the sample and a computer which takes the data and controls the experiment. Experimental data will include gas-phase and solid-phase temperature measurements and motion pictures of the combustion process. Flame spread rates will be determined from the motion pictures.

Vento, D. M.↗