Engineering topics

Venkatapathy, Ethiras

Publications and source records attributed to Venkatapathy, Ethiras.

6 records

NASA NTRS2002

Morphologies, Processing and Properties of Ceramic Foams from Pre-Ceramic Foams from Pre-Ceramic Polymer Routes

The current research is focused on processing ceramic foams that have potential as a thermal protection material. Ceramic foams with different architectures were formed from the pyrolysis of pre-ceramic polymers at 1200 C in different atmospheres. In some systems a sacrificial polyurethane was used as the blowing agent. We have also processed foams using sacrificial fillers to introduce controlled cell sizes. Each sacrificial filler or blowing agent leads to a unique morphology. The effect of different fillers on foam morphologies will be presented. The presentation will also focus on characterization of these foams in terms of mechanical and thermal properties. Foams processed using these approaches having bulk densities ranging from 0.15 to 0.9 g per cubic centimeter and a cell sizes from 5 to 500 micrometers. Compression strengths ranged from 2 to 7 MPa for these materials.

Stackpoole, Mairead↗

NASA NTRS2002

Sol-Gel Derived Hafnia Coatings

Sol-gel derived hafnia coatings are being developed to provide an oxidation protection layer on ultra-high temperature ceramics for potential use in turbine engines (ultra-efficient engine technology being developed by NASA). Coatings using hafnia sol hafnia filler particles will be discussed along with sol synthesis and characterization.

Feldman, Jay D.↗

NASA NTRS2002

Thermal Protection System Evaluation Using Arc-jet Flows: Flight Simulation or Research Tool?

The arc-jet has been used to evaluate thermal protection systems (TPS) and materials for the past forty years. Systems that have been studied in this environmerd include ablators, active, and passive TPS concepts designed for vehicles entering planetary and Earth atmospheres. The question of whether arc-jet flow can simulate a flight environment or is it a research tool that provides an aero-thermodynamic heating environment to obtain critical material properties will be addressed. Stagnation point tests in arc-jets are commonly used to obtain material properties such as mass loss rates, thermal chemical stability data, optical properties, and surface catalytic efficiency. These properties are required in computational fluid dynamic codes to accurately predict the performance of a TPS during flight. Special facilities have been developed at NASA Ames Research Center to approximate the flow environment over the mid-fuselage and body flap regions of proposed space-planes type vehicles. This paper compares flow environments generated in flight over a vehicle with those created over an arc-jet test articles in terms of scale, chemistry, and fluid dynamic properties. Flight experiments are essential in order to validate the material properties obtained from arc-jet tests and used to predict flight performance of any TPS being considered for use on a vehicle entering the Earth atmosphere at hypersonic speed.

Stewart, David A.↗

NASA NTRS2002

Reusable Surface Insulation Tile Thermal Protection Materials: Past, Present and the Future

Silica (LI-900) Reusable Surface Insulation (RSI) tile have been used on the majority of the Shuttle since its initial flight. Its overall performance with Reaction Cured Glass (RCG) coating applied will be reviewed. Improvements in insulations, Fibrous Refractory Composite Insulation (FRCI-12) and Alumina Enhanced Thermal Barrier (AETB-8) and coatings/surface treatments such as Toughened Uni-Piece Fibrous Insulation (TUFI) have been developed and successfully applied. The performance of these enhancements on the Shuttle Orbiters over the past few years along with the next version of tile materials, High Efficiency Tantalum-based Ceramic (HETC) with even broader applicability will also be discussed.

Leiser, Daniel B.↗

NASA NTRS2002

Alternative Processing Methods for Ultra High Temperature Ceramics

Ultra High Temperature Ceramics (UHTCs) are being developed for possible use in a number of structural applications including hypersonic vehicles, engines, plasma arc electrodes and high temperature shielding. Alternative methods of processing Ultra High Temperature Ceramics (UHTCs) will be discussed. Techniques that may improve oxidation resistance, strength, and reduce the processing temperature of the UHTCs will be presented. Hot-pressed UHTCs made using either milled/uncoated powders or non-milled coated powders will be compared.

Gusman, Michael↗

NASA NTRS2002

HfB2-SiC Materials for Sharp Leading Edges

Future reentry vehicles will need better maneuverability to improve safety and performance. Vehicles with sharp leading edges, as opposed to the blunt nose and leading edges on the current space shuttle, can provide improved lift-to-drag and thus improved maneuverability. Materials capable of operating at temperatures in excess of 2000 C are required. Ultrahigh temperature ceramics (UHTCs) are one class of material being investigated for this application. These materials are diborides of hafnium or zirconium with a second phase of sic. The benefits of using these materials will be discussed as developments in the processing of HfB2/SiC.

Johnson, Sylvia M.↗