Engineering Papers⌕ Search

Engineering topics

Vaniman, D. T.

Publications and source records attributed to Vaniman, D. T..

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS2004

Evaluation of Rock Powdering Methods to Obtain Fine-grained Samples for CHEMIN, a Combined XRD/XRF Instrument

A miniature XRD/XRF (X-ray diffraction / X-ray fluorescence) instrument, CHEMIN, is currently being developed for definitive mineralogic analysis of soils and rocks on Mars. One of the technical issues that must be addressed to enable remote XRD analysis is how best to obtain a representative sample powder for analysis. For powder XRD analyses, it is beneficial to have a fine-grained sample to reduce preferred orientation effects and to provide a statistically significant number of crystallites to the X-ray beam. Although a two-dimensional detector as used in the CHEMIN instrument will produce good results even with poorly prepared powder, the quality of the data will improve and the time required for data collection will be reduced if the sample is fine-grained and randomly oriented. A variety of methods have been proposed for XRD sample preparation. Chipera et al. presented grain size distributions and XRD results from powders generated with an Ultrasonic/Sonic Driller/Corer (USDC) currently being developed at JPL. The USDC was shown to be an effective instrument for sampling rock to produce powder suitable for XRD. In this paper, we compare powder prepared using the USDC with powder obtained with a miniaturized rock crusher developed at JPL and with powder obtained with a rotary tungsten carbide bit to powders obtained from a laboratory bench-scale Retsch mill (provides benchmark mineralogical data). These comparisons will allow assessment of the suitability of these methods for analysis by an XRD/XRF instrument such as CHEMIN.

Chipera, S. J.↗
NASA NTRS2004

Definitive Mineralogical Analysis of Mars Analog Rocks Using the CheMin XRD/XRF Instrument

Mineral identification is a critical component of Mars Astrobiological missions. Chemical or elemental data alone are not definitive because a single elemental or chemical composition or even a single bonding type can represent a range of substances or mineral assemblages. Minerals are defined as unique structural and compositional phases that occur naturally. There are about 15,000 minerals that have been described on Earth, all uniquely identifiable via diffraction methods. There are likely many minerals yet undiscovered on Earth, and likewise on Mars. If an unknown phase is identified on Mars, it can be fully characterized by structural (X-ray Diffraction, XRD) and elemental analysis (X-ray Fluorescence, XRF) without recourse to other data because XRD relies on the principles of atomic arrangement for its determinations. XRD is the principal means of identification and characterization of minerals on Earth.

Blake, D. F.↗
NASA NTRS2004

Quantitative Mineralogical Analysis of Mars Analogues Using CHEMIN Data and Rietveld Refinement

Mineralogical analysis is a critical component of planetary surface exploration. Chemical data alone leave serious gaps in our understanding of the surfaces of planets where complex minerals may form in combination with H, S, and halogens. On such planets (e.g., Mars) a single chemical composition may represent a range of mineral assemblages. For example, Viking chemical analyses of excavated duricrust indicate that Mg and S are correlated and ~10% MgSO4 (anhydrous weight) is a likely cementing agent. Pathfinder chemical data support a similar abundance of MgSO4 in the most altered materials. However, there are many possible Mg-sulfates with widely varying hydration states (including dehydrated and 1-, 2-, 3-, 4-, 5-, 6-, and 7-hydrates). In addition, other sulfate minerals such as gypsum (CaSO4 .2H2O) and other salts containing Cl may also exist. X-ray diffraction (XRD) has the ability to decipher mixtures of these phases that would be difficult, if not impossible to unravel using only chemical or spectral data.

Bish, D. L.↗
NASA NTRS2003

Use of an Ultrasonic/Sonic Driller/Corer to Obtain Sample Powder for CHEMIN, a Combined XRD/XRF Instrument

A miniature CHEMIN XRD/XRF (X-Ray Diffraction/X-Ray Fluourescence) instrument is currently being developed for definitive mineralogic analysis of soils and rocks on Mars. One of the technical issues that must be addressed in order to enable XRD analysis on an extraterrestrial body is how best to obtain a representative sample powder for analysis. For XRD powder diffraction analyses, it is beneficial to have a fine-grained sample to reduce preferred orientation effects and to provide a statistically significant number of crystallites to the X-ray beam. Although a 2-dimensional detector as used in the CHEMIN instrument will produce good results with poorly prepared powders, the quality of the data will improve if the sample is fine-grained and randomly oriented. An Ultrasonic/Sonic Driller/Corer (USDC) currently being developed at JPL is an effective mechanism of sampling rock to produce cores and powdered cuttings. It requires low axial load (< 5N) and thus offers significant advantages for operation from lightweight platforms and in low gravity environments. The USDC is lightweight (<0.5kg), and can be driven at low power (<5W) using duty cycling. It consists of an actuator with a piezoelectric stack, ultrasonic horn, free-mass, and drill bit. The stack is driven with a 20 kHz AC voltage at resonance. The strain generated by the piezoelectric is amplified by the horn by a factor of up to 10 times the displacement amplitude. The tip impacts the free-mass and drives it into the drill bit in a hammering action. The free-mass rebounds to interact with the horn tip leading to a cyclic rebound at frequencies in the range of 60-1000 Hz. It does not require lubricants, drilling fluid or bit sharpening and it has the potential to operate at high and low temperatures using a suitable choice of piezoelectric material. To assess whether the powder from an ultrasonic drill would be adequate for analyses by an XRD/XRF spectrometer such as CHEMIN, powders obtained from the JPL ultrasonic drill were analyzed and the results were compared to carefully prepared powders obtained using a laboratory bench scale Retsch mill.

Chipera, S. J.↗
NASA NTRS2001

Aerogel as a Sample Collector and Sample Mount for Transmission XRD Analysis

Silica aerogel can be used for dust collection and in situ X-ray analysis. Aerogels can be less absorbing than Be, and it is feasible to obtain X-ray transmission factors >50% using typical aerogels together with a 100-micrometer Be backing foil. Additional information is contained in the original extended abstract.

Bish, D. L.↗
NASA NTRS2000

CCD-Based XRD/XRF for Determining Environmental Mineralogy on Mars

Health effects from Martian dusts will be a concern for any manned Mars missions. Nuisance dusts plagued the Apollo astronauts, but dusts of more hazardous mineralogy, in habitats occupied by Mars astronauts weakened by a long-duration mission, may be more than a nuisance. Chemical hazards in Martian regolith attributable to S, Cl, Br, Cd, and Pb are known or strongly suspected to be present, but terrestrial studies of the health effects of dusts indicate that accurate determination of mineralogy is a critical factor in evaluating inhalation hazards. Mineral inhalation hazards such as the Group-I carcinogenic zeolite erionite, which is demonstrated to cause mesothelioma, cannot be identified by chemical analysis alone. Studies of palagonite analogs raise the possibility that erionite may occur on Mars. In addition to health effects concerns, environmental mineralogy has significant importance in resource extraction, groundwater use, and sustained agriculture. The high sulfur and chlorine content of Martian regolith will affect all of these uses, but the nature of mineralogic reservoirs for S and Cl will determine their uptake and concentration in extracted groundwater and in agricultural applications of regolith. Wet chemistry experiments planned for the Mars Environmental Compatibility Assessment (MECA) will define some of the consequences of water/soil interaction, but an understanding of the mineralogic basis for water-rock reactions is needed to understand the mechanisms of reaction and to apply the results of a few experiments to larger scales and different conditions.

Vaniman, D. T.↗
NASA NTRS1992

A Combined XRD/XRF Instrument for Lunar Resource Assessment

Robotic surface missions to the Moon should be capable of measuring mineral as well as chemical abundances in regolith samples. Although much is already known about the lunar regolith, our data are far from comprehensive. Most of the regolith samples returned to Earth for analysis had lost the upper surface, or it was intermixed with deeper regolith. This upper surface is the part of the regolith most recently exposed to the solar wind; as such it will be important to resource assessment. In addition, it may be far easier to mine and process the uppermost few centimeters of regolith over a broad area than to engage in deep excavation of a smaller area. The most direct means of analyzing the regolith surface will be by studies in situ. In addition, the analysis of the impact-origin regolith surfaces, the Fe-rich glasses of mare pyroclastic deposits, are of resource interest, but are inadequately known; none of the extensive surface-exposed pyroclastic deposits of the Moon have been systematically sampled, although we know something about such deposits from the Apollo 17 site. Because of the potential importance of pyroclastic deposits, methods to quantify glass as well as mineral abundances will be important to resource evaluation. Combined x ray diffraction (XRD) and x ray fluorescence (XRF) analysis will address many resource characterization problems on the Moon. XRF methods are valuable for obtaining full major-element abundances with high precision. Such data, collected in parallel with quantitative mineralogy, permit unambiguous determination of both mineral and chemical abundances where concentrations are high enough to be of resource grade. Collection of both XRD and XRF data from a single sample provides simultaneous chemical and mineralogic information. These data can be used to correlate quantitative chemistry and mineralogy as a set of simultaneous linear equations, the solution of which can lead to full characterization of the sample. The use of Rietveld methods for XRD data analysis can provide a powerful tool for quantitative mineralogy and for obtaining crystallographic data on complex minerals.

Vaniman, D. T.↗
NASA NTRS1990

Getting lunar ilmenite - From soils or rocks?

Lunar soils or rocks can be mined as sources of ilmenite for producing oxygen. However, separable crystals of loose ilmenite in lunar soils are rare (less than 2 percent) and small (less than 200 microns); most ilmenite in the regolith is locked together with silicate minerals as rock fragments. If fragmentation of rock sources must be attempted to win appreciable amounts of ilmenite (approximately 10 percent or more), selective collection of high-Ti basalt fragments larger than 1 cm for fragmentation and ilmenite beneficiation may be advantageous over extensive processing of fine lunar soil. Many alternative processing schemes for fragmenting rocks on the Moon have been proposed; one process which was tested early in the Apollo program successfully disaggregated lunar and terrestrial basalts by passive exposure to low-pressure alkali (K) vapor. This process is worthy of reinvestigation.

Vaniman, D. T.↗
NASA NTRS1986

Mars surface science requirements and plan

The requirements for obtaining geological, geochemical, geophysical, and meteorological data on the surface of Mars associated with manned landings were analyzed. Specific instruments were identified and their mass and power requirements estimated. A total of 1 to 5 metric tons, not including masses of drill rigs and surface vehicles, will need to be landed. Power associated only with the scientific instruments is estimated to be 1 to 2 kWe. Requirements for surface rover vehicles were defined and typical exploration traverses during which instruments will be positioned and rock and subsurface core samples obtained were suggested.

Blacic, J. D.↗
NASA NTRS1980

Lunar highland melt rocks - Chemistry, petrology and silicate mineralogy

A selected suite containing several of the largest samples of lunar highland melt rocks includes impact melt specimens (anorthositic gabbro, low-K Fra Mauro) and volcanic specimens (intermediate-K Fra Mauro). Although previous assumptions of LKFM volcanism have fallen into disfavor, no fatal arguments against this hypothesis have been presented, and the evidence of a possibly 'inherited igneous' olivine-plagioclase cosaturation provides cause for keeping a volcanic LKFM hypothesis viable. Comparisons of silicate mineralogy with melt rock compositions provide information on the specimen's composition and cooling history. Plagioclase-rock compositions can be matched to the experimentally determined equilibria for appropriate samples to identify melt rocks with refractory anorthitic clasts. Olivine-rock compositions indicate that melt rock vitrophyres precipitate anomalously Fe-rich olivine; the cause of this anomaly is not immediately evident. The Al-Ti and Ca-Fe-Mg zonation in pyroxene provide information on relative cooling rates of highland melt rocks, but Cr- and Al-content (where Al-rich low-Ca pyroxene cores are preserved in rapidly cooled samples) can be correlated with composition of the host rock.

Vaniman, D. T.↗
NASA NTRS1979

The Apollo 17 drill core - Petrologic systematics and the identification of a possible Tycho component

Modal data support a five-unit stratigraphy for the Apollo 17 drill core. The upper unit E (0-22 cm depth) is marked by high content of fused soil, brown glass, and mare basalt fragments. This unit corresponds with a portion of the core excavated and refilled within the last 2 m.y. The underlying unit D (22071 cm depth) has a low abundance of fused soil (i.e., low maturity) and is rich in coarse (less than 200 microns) mare fragments. A large section of the core, unit C (71-224 cm depth), is finer-grained, more mature (richer in agglutinates), more feldspathic and has more highland lithic, mineral and glass fragments than unit D. The next underlying unit, B (224-256 cm depth), has yellow/colorless KREEP glasses with a high Si, low-alkali composition unlike the common Apollo 15 or Apollo 17 KREEP series. The petrologic (fused soil) and Is/FeO maturity of this layer is also lower than the units above and below. The deepest unit, A (256-284 cm depth), is marked by its relatively higher maturity and lower yellow/colorless KREEP glass content. The most prominent petrographic/stratigraphic indicators are the pyroxene-rich immature mare unit D and the abundance of KREEP glass in unit B. This KREEP glass is distinctive petrographically and compositionally, and is probably exotic to the Apollo 17 site. It is suggested here that the KREEP glass in unit B is derived from Tycho, which implies widespread distribution of KREEP on the lunar nearside.

Vaniman, D. T.↗
NASA NTRS1979

The Apollo 17 drill core - Chemical systematics of grain size fractions

Data for 35 major, minor, and trace elements in 40 bulk and size fractions of core 70005-70003 (140-250 cm) are presented. The core is heterogeneous with depth. Moreover, the 1000 to 90 micron coarse fractions are nearly identical but quite different from the less than 20 micron fine fraction. The bulk soil chemistry is governed by the coarse fractions, because of their greater weight proportion in the sample. The 1000-90 micron fraction contains more ilmenite basalt and less orange glass components than the 90-20 micron fraction. The less than 20 micron fraction is consistently enriched in highland material at all depths in the drill core.

Laul, J. C.↗
NASA NTRS1978

The lunar highland melt-rock suite

Size can be used as a criterion to select 18 large (larger than 1 cm) samples from among 148 melt-rock fragments of all sizes. This selection provides a suite of large samples which represent the important chemical variants among highland melt rocks; each large sample has enough material for a number of sample-destructive studies, as well as for future reference. Cluster analysis of the total data base of 148 highland melt rocks shows six distinct groups: anorthosite, gabbroic anorthosite, anorthositic gabbro ('highland basalt'), low K Fra Mauro, intermediate-K Fra Mauro, and high-K. Large samples are available for four of the melt-rock groups (gabbroic anorthosite, anorthositic gabbro, low-K Fra Mauro, and intermediate-K Fra Mauro). This sample selection reveals two subgroups of anorthositic gabbro (one anorthite-poor with negative Eu anomaly and one anorthite-rich without Eu anomaly). There is a sharp distinction between those Apollo 16 melt rocks and glasses which have both been classified as 'gabbroic anorthosite'.

Vaniman, D. T.↗
NASA NTRS1978

The lunar mare basalt suite

Recent studies have greatly expanded knowledge of lunar mare basalts. Since 1976 there has been a revision of the Apollo 12 low-Ti mare basalt suite and the discovery of a new very low-Ti (VLT: less than 1% TiO2) basalt suite at Apollo 17 and in the new Soviet samples from Mare Crisium (LUNA 24). Current studies suggest that the VLT basalts may be in some way related to the enigmatic 'green glasses' which are found in the soils from every lunar landing site. Telescopic studies of spectral reflectance and crater systematics show that basalts of varying Ti content were extruded throughout the history of mare volcanism. These new discoveries indicate that mare basalts can no longer be classified into the two simple groups of older high-Ti basalts and younger low-Ti basalts.

Papike, J. J.↗
NASA NTRS1978

Experimental petrology of very low Ti /VLT/ basalts

Synthetic analogs of Luna 24 ferrobasalt and an Apollo 15 green glass were subjected to iron capsule experiments to test hypotheses concerning the generation of Luna 24 ferrobasalt. Results of the experiments indicated that the Luna 24 ferrobasalt may be generated by near-surface fractionation of a Luna 24 green glass parent. Evidence for the parent magma which differentiated at or near the Mare Crisium site to yield the Luna 24 ferrobasalt may be found in the Luna 24 green glass and lithic fragments of vitrophyres.

Grove, T. L.↗