Engineering Papers⌕ Search

Engineering topics

Vandersall, Kevin S.

Publications and source records attributed to Vandersall, Kevin S..

Temperature-based reactive flow model for TATB plastic bonded explosives

A new reactive flow model is presented for TATB-based plastic bonded explosives, applicable to shock initiation and detonation problems of differing initial temperature. Temperature disequilibrium is assumed between unreacted explosive, material in the vicinity of compressed defects (called hot spots), and detonation products. The model incorporates temperature-dependent decomposition reaction rates. Arrhenius model parameters were derived from subscale quantum-based molecular dynamics simulations of shock-induced TATB decomposition. Further, a model of detonation carbon aggregation is incorporated, describing the late-time slow release of energy inherent to detonation in TATB-based materials. The predictive ability of the model in the shock initiation regime is tested against recent thin pulse experiments on PBX 9502. Here, the model is found to perform equally well in predicting the size effect curve of ambient, cold, and hot PBX 9502 rate sticks.

Chemistry - Chemical explosives↗

Observation of asymmetric explosive density evolution in the deflagration-to-detonation transition for porous explosives

We report deflagration-to-detonation transition phenomena in cylindrical columns of porous explosives based on octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazocine (HMX). The HMX powder and LX-14 (95.5 wt. % HMX and 4.5 wt. % estane polyurethane) prills were observed with high-speed cameras and flash x rays under conditions that allow for precise scaling and registration of the recorded images. These experimental results test the conventional assumption of axisymmetric, effective one-dimensional burning. Polycarbonate confinement tubes allowed this direct imaging with steel spheres employed as radio-opaque fiducials. Spheres embedded in the explosive column revealed the displacement of the explosive prior to deflagration. X-ray and fast camera images show that a dense plug of compact explosive develops ahead of the deflagration front. The internal fiducials register both internal changes in the plug and changes in the position between successive x-ray images. Tantalum witness strips placed on the inner wall of the explosive channel revealed radial expansion of the tube bore at successive x-ray exposures, indicating the internal pressure of about 100 MPa just before detonation. Images indicate that the deflagration is not only asymmetric but also involves newly observed transient phenomena just before detonation. Furthermore, we typically see a brief but continuous increase in deflagration speed and the formation of a deflagration channel that bypasses the plug just prior to detonation. We hypothesize that these phenomena play an important role in the deflagration-to-detonation transition itself.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Encapsulated microenergetic material

Providing high energy materials that can be placed in previously created fractures and activating them in place to extend or change an existing fracture system. Also detecting the location of fractures or permeable pathways and a means to assess the extent and efficiency of proppant emplacement.

42 ENGINEERING↗

Encapsulated microenergetic material

Providing high energy materials that can be placed in previously created fractures and activating them in place to extend or change an existing fracture system. Also detecting the location of fractures or permeable pathways and a means to assess the extent and efficiency of proppant emplacement.

36 MATERIALS SCIENCE↗

SPE5 Sub-Scale Test Series Summary Report

A series of 2 SPE5 sub-scale tests were performed to experimentally confirm that a booster system designed and evaluated in prior tests would properly initiate the PBXN-110 case charge fill. To conduct the experiments, a canister was designed to contain the nominally 50 mm diameter booster tube with an outer fill of approximately 150 mm diameter by 150 mm in length. The canisters were filled with PBXN-110 at NAWS-China Lake and shipped back to LLNL for testing in the High Explosives Applications Facility (HEAF). Piezoelectric crystal pins were placed on the outside of the booster tube before filling, and a series of piezoelectric crystal pins along with Photonic Doppler Velocimetry (PDV) probes were placed on the outer surface of the canister to measure the relative timing and magnitude of the detonation. The 2 piezoelectric crystal pins integral to the booster design were also utilized along with a series of either piezoelectric crystal pins or piezoelectric polymer pads on the top of the canister or outside case that utilized direct contact, gaps, or different thicknesses of RTV cushions to obtain time of arrival data to evaluate the response in preparation for the large-scale SPE5 test. To further quantify the margin of the booster operation, the 1st test (SPE5SS1) was functioned with both detonators and the 2nd test (SPE5SS2) was functioned with only 1 detonator. A full detonation of the material was observed in both experiments as observed by the pin timing and PDV signals. The piezoelectric pads were found to provide a greater measured signal magnitude during the testing with an RTV layer present, and the improved response is due to the larger measurement surface area of the pad. This report will detail the experiment design, canister assembly for filling, final assembly, experiment firing, presentation of the diagnostic results, and a discussion of the results.

36 MATERIALS SCIENCE↗

PETN Sample Preparation Safety Limits

27 psi has been determined to be the maximum allowable pressure for contact operations with PETN at LLNL. Pressures above this limit can be tested, but samples must be prepared via remote handling operations. This document summarizes the safety review and discussion that took place at LLNL to define this pressure limit.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗