Engineering topics

Vanderplaats, G. N.

Publications and source records attributed to Vanderplaats, G. N..

At least 37 records · Page 2

NASA NTRS1983

A robust Feasible Directions algorithm for design synthesis

A nonlinear optimization algorithm is developed which combines the best features of the Method of Feasible Directions and the Generalized Reduced Gradient Method. This algorithm utilizes the direction-finding sub-problem from the Method of Feasible Directions to find a search direction which is equivalent to that of the Generalized Reduced Gradient Method, but does not require the addition of a large number of slack variables associated with inequality constraints. This method provides a core-efficient algorithm for the solution of optimization problems with a large number of inequality constraints. Further optimization efficiency is derived by introducing the concept of infrequent gradient calculations. In addition, it is found that the sensitivity of the optimum design to changes in the problem parameters can be obtained using this method without the need for second derivatives or Lagrange multipliers. A numerical example is given in order to demonstrate the efficiency of the algorithm and the sensitivity analysis.

Vanderplaats, G. N.↗

NASA NTRS1981

Numerical optimization of circulation control airfoils

A numerical procedure for optimizing circulation control airfoils, which consists of the coupling of an optimization scheme with a viscous potential flow analysis for blowing jet, is presented. The desired airfoil is defined by a combination of three baseline shapes (cambered ellipse, and cambered ellipse with drooped and spiralled trailing edges). The coefficients of these shapes are used as design variables in the optimization process. Under the constraints of lift augmentation and lift-to-drag ratios, the optimal airfoils are found to lie between those of cambered ellipse and the drooped trailing edge, towards the latter as the angle of attack increases. Results agree qualitatively with available experimental data.

Tai, T. C.↗

NASA NTRS1980

Optimized laser turrets for minimum phase distortion

An analysis and computer program which optimizes laser turret geometry to obtain minimum phase distortion is described. Phase distortion due to compressible, inviscid flow over small perturbation laser turrets in subsonic or supersonic flow is calculated. The turret shape is determined by a two dimensional Fourier series; in a similar manner, the flow properties are given by a Fourier series. Phase distortion is calcualted for propagation at serveral combinations of elevation and azimuth angles. A sum is formed from the set of values, and this sum becomes the objective function for an optimization computer program. The shape of the turret is varied to provide minimum phase distortion.

Vanderplaats, G. N.↗

NASA NTRS1979

Automated design using numerical optimization

Numerical optimization concepts are described with limited technical detail. The purpose is to provide the nonspecialist with sufficient information to judge the applicability of these methods to his particular design problem. The concepts are first described in physical terms to give a basic understanding of the iterative procedure employed by these methods. Next, the typical engineering task is presented and converted to a form ammenable to solution by numerical optimization. Basic algorithms for solving this problem are identified. Numerous applications are referenced, emphasizing the structural design discipline. The state of the art allows for the routine solution of nonlinear design problems of approximately 20 independent variables subject to 100 or more constraints. In many applications, much larger design problems may be solved. Selected references are provided which describe the methods and applications in more detail.

Vanderplaats, G. N.↗

NASA NTRS1979

Approximation concepts for numerical airfoil optimization

An efficient algorithm for airfoil optimization is presented. The algorithm utilizes approximation concepts to reduce the number of aerodynamic analyses required to reach the optimum design. Examples are presented and compared with previous results. Optimization efficiency improvements of more than a factor of 2 are demonstrated. Improvements in efficiency are demonstrated when analysis data obtained in previous designs are utilized. The method is a general optimization procedure and is not limited to this application. The method is intended for application to a wide range of engineering design problems.

Vanderplaats, G. N.↗

NASA NTRS1979

An efficient algorithm for numerical airfoil optimization

A new optimization algorithm is presented. The method is based on sequential application of a second-order Taylor's series approximation to the airfoil characteristics. Compared to previous methods, design efficiency improvements of more than a factor of 2 are demonstrated. If multiple optimizations are performed, the efficiency improvements are more dramatic due to the ability of the technique to utilize existing data. The method is demonstrated by application to subsonic and transonic airfoil design but is a general optimization technique and is not limited to a particular application or aerodynamic analysis.

Vanderplaats, G. N.↗

NASA NTRS1977

Application of numerical optimization to the design of supercritical airfoils without drag-creep

Recent applications of numerical optimization to the design of advanced airfoils for transonic aircraft have shown that low-drag sections can be developed for a given design Mach number without an accompanying drag increase at lower Mach numbers. This is achieved by imposing a constraint on the drag coefficient at an off-design Mach number while the drag at the design Mach number is the objective function. Such a procedure doubles the computation time over that for single design-point problems, but the final result is worth the increased cost of computation. The ability to treat such multiple design-point problems by numerical optimization has been enhanced by the development of improved airfoil shape functions. Such functions permit a considerable increase in the range of profiles attainable during the optimization process.

Hicks, R. M.↗

NASA NTRS1976

Automated optimization techniques for aircraft synthesis

Application of numerical optimization techniques to automated conceptual aircraft design is examined. These methods are shown to be a general and efficient way to obtain quantitative information for evaluating alternative new vehicle projects. Fully automated design is compared with traditional point design methods and time and resource requirements for automated design are given. The NASA Ames Research Center aircraft synthesis program (ACSYNT) is described with special attention to calculation of the weight of a vehicle to fly a specified mission. The ACSYNT procedures for automatically obtaining sensitivity of the design (aircraft weight, performance and cost) to various vehicle, mission, and material technology parameters are presented. Examples are used to demonstrate the efficient application of these techniques.

Vanderplaats, G. N.↗

NASA NTRS1976

Numerical Airfoil Optimization Using a Reduced Number of Design Coordinates

A method is presented for numerical airfoil optimization whereby a reduced number of design coordinates are used to define the airfoil shape. The approach is to define the airfoil as a linear combination of shapes. These basic shapes may be analytically or numerically defined, allowing the designer to use his insight to propose candidate designs. The design problem becomes one of determining the participation of each such function in defining the optimum airfoil. Examples are presented for two-dimensional airfoil design and are compared with previous results based on a polynomial representation of the airfoil shape. Four existing NACA airfoils are used as basic shapes. Solutions equivalent to previous results are achieved with a factor of more than 3 improvements in efficiency, while superior designs are demonstrated with an efficiency greater than 2 over previous methods. With this shape definition, the optimization process is shown to exploit the simplifying assumptions in the inviscid aerodynamic analysis used here, thus demonstrating the need to use more advanced aerodynamics for airfoil optimization.

Vanderplaats, G. N.↗

NASA NTRS1976

Airfoil section drag reduction at transonic speeds by numerical optimization

A practical procedure for the design of low drag, transonic airfoils is demonstrated. The procedure uses an optimization program, based on a gradient algorithm coupled with an aerodynamic analysis program, that solves the full, non-linear potential equation for transonic flow. The procedure is useful for the design of retrofit modifications for drag reduction of existing aircraft as well as for the design of low drag profiles for new aircraft. Results are presented for the modification of four different airfoils to decrease the drag at a given transonic Mach number.

Hicks, R. M.↗

NASA NTRS1976

Airfoil section drag reduction at transonic speeds by numerical optimization

Hicks, R. M.↗

NASA NTRS1976

COMMAND: A FORTRAN program for simplified composite analysis and design

A FORTRAN program is presented for preliminary analysis and design of multilayered composite panels subjected to inplane loads. All plys are of the same material. The composite is assumed symmetric about the midplane, but need not be balanced. Failure criterion includes limit ply strains and lower bounds on composite inplane stiffnesses. Multiple load conditions are considered. The required input data is defined and examples are provided to aid the use in making the program operational. Average panel design times are two seconds on an IBM 360/67 computer. Results are compared with published literature. A complete FORTRAN listing of program COMAND is provided. In addition, the optimization program CONMIN is required for design.

Vanderplaats, G. N.↗

NASA NTRS1976

Structural optimization via a design space hierarchy

Mathematical programming techniques provide a general approach to automated structural design. An iterative method is proposed in which design is treated as a hierarchy of subproblems, one being locally constrained and the other being locally unconstrained. It is assumed that the design space is locally convex in the case of good initial designs and that the objective and constraint functions are continuous, with continuous first derivatives. A general design algorithm is outlined for finding a move direction which will decrease the value of the objective function while maintaining a feasible design. The case of one-dimensional search in a two-variable design space is discussed. Possible applications are discussed. A major feature of the proposed algorithm is its application to problems which are inherently ill-conditioned, such as design of structures for optimum geometry.

Vanderplaats, G. N.↗

NASA NTRS1976

Design of structures for optimum geometry

A general method is proposed for geometric optimization of finite element structures on the assumption that a reasonable initial geometry is specified. The number of finite elements, number of joints, and the element-joint relationships are specified and are not changed during the optimization process. The structure may be statically indeterminate and may support multiple loading conditions. Design variables include geometric and member sizing parameters. Design objectives may be minimum weight or cost, and constraints include strength and stiffness limitations. The optimization procedure is a general mathematical programming approach. An iterative design algorithm is outlined, and the method is specialized for truss structures. Design examples are given.

Vanderplaats, G. N.↗

NASA NTRS1976

The computer for design and optimization

Computerized design using numerical optimization techniques is discussed and guidelines for writing analysis computer codes that can be readily coupled to optimization codes are presented. The following numerical optimization techniques are examined: random search, sequential unconstrained minimization, direct constrained optimization, and one-dimensional search. A number of design applications are considered including high speed airfoil lift maximization, the preliminary design of a wing, design of a planar tower for optimal geometry, and the conceptual design of a tactical fighter aircraft.

Vanderplaats, G. N.↗

NASA NTRS1975

Design of structures for optimum geometry

A method is presented for configuration optimization of finite element structures, given a reasonable initial geometry. The objective is to minimize weight or cost. Design variables include geometric as well as member sizing parameters. The number of elements and joints, and the element-joint relationships are prescribed and are not changed during the optimization process. However, the joint locations are changed. The structure is assumed to be linearly elastic and may be statically indeterminate. Multiple loading conditions are allowed. Constraints include limits on stiffness as well as strength. The method is demonstrated with application to truss design, subject to minimum size, strength, buckling, and displacement constraints. Major design improvements are achieved through configurations changes.

Vanderplaats, G. N.↗

NASA NTRS1975

The auxiliary problem for feasible directions

The present work compares the computational efficiency of two means of determining a direction vector S at constraint boundaries and demonstrates the advantages of using the alternative that formulates the S-determination subproblem with a single quadratic constraint, which in turn can be cast as a special linear problem and solved directly.

Gwin, L. B.↗

NASA NTRS1975

Design of low-speed airfoils by numerical optimization

A practical procedure for the optimum design of low-speed airfoils is demonstrated. The procedure uses an optimization program based on a gradient algorithm coupled with an aerodynamic analysis program that uses a relaxation solution of the inviscid, full-potential equation. The analysis program is valid for both incompressible and compressible flow, thereby making optimum design of high-speed, shock-free airfoils possible. Results are presented for the following three constrained optimization problems at fixed angle of attack and Mach number: (1) adverse pressure-gradient minimization, (2) pitching-moment minimization; and (3) lift maximization. All three optimization problems were studied with various aerodynamic and geometric constraints.

Hicks, R. M.↗