Engineering topics

Upadhyaya, Vijaykumar

Publications and source records attributed to Upadhyaya, Vijaykumar.

4 records

DOE OSTI2023

Hydrogen Sulfide Passivation for p-Type Passivated Emitter and Rear Contact Solar Cells

This work reports on the application of sulfur (S)-passivation to passivated emitter and rear contact (PERC) solar cells. The emitter surface was passivated by hydrogen sulfide (H 2 S) gas phase reaction and capped by a hydrogenated amorphous silicon nitride (a-SiN x :H) layer. The sulfur passivation on a symmetrically n + diffused emitter is shown to lead to an emitter saturation current density (J 0n+ ) of 30 fA/cm 2 at R sheet,n+ ≈ 100 Ω/sq. The application of S-passivation to the emitter surface in the PERC cell structure, with the rear surface passivated by an aluminum oxide (Al 2 O 3 )/a-SiN x :H stack, showed a promising implied open-circuit voltage (iV OC ) of 686 mV before metallization. This iV OC was higher than that for the a-SiN x :H or SiO 2 /a-SiN x :H passivated emitter surfaces (675 and 674 mV, respectively) on PERC cells processed in the same run. However, a significant drop in cell V OC is observed for the S-passivated PERC cell after the completion of device fabrication with laser patterning, screen-printed metal contact deposition, and firing. Nonetheless, an efficiency of ~20% and a V OC of ~650 mV was achieved with an emitter surface passivated by sulfur. We identified that the 760°C contact firing process degrades the S-passivation quality. Furthermore, the surface morphology was studied, and a detailed surface analysis was performed to study the causes of the S-passivated surface degradation.

14 SOLAR ENERGY↗

DOE OSTI2022

Investigation of long-term light stability of negative charge injected into oxide-nitride-oxide passivation stack of crystalline silicon solar cells

A negatively charged oxide-nitride-oxide stack for field-effect passivation of crystalline silicon solar cells is discussed. The negative charge was injected into the stack by a plasma charge injection technology. Charge stability was studied by exposing samples to AM1.5 simulation visible light and full-spectrum light at temperatures ranging from 55 to 78 °C for up to 300 h. Charge injection and loss were quantified based on shifts in the flatband voltage of capacitance–voltage curves measured with a mercury probe. The most probable mechanism of charge loss was found to be diffusion of negative charged hydrogen atoms through nitride and bottom oxide. The optimum recipe for each layer of the stack was investigated to minimize the loss of injected charge. The flatband voltage decay of the optimized stack was found to fit a power-law trend, suggesting the dispersive transport of hydrogen atoms with a dispersion parameter of ~0.06–0.07. The optimized stack is projected to maintain a negative charge density of about 3.6 × 10 12 cm –2 or more after 25 years of field operation in an environment such as Arizona, which would be sufficient for field-effect passivation under one-sun illumination. Furthermore, the high stability of the negative injected charge makes the plasma charging technology a safer and lower cost alternative to Al 2 O 3 -passivation technology commonly used to passivate p-type surfaces.

14 SOLAR ENERGY↗

DOE OSTI2022

Technology Development for ≥ 22.5% Efficient p-PERC Solar Cells

The overall objective of this program is to achieve ≥ 22.5 % bifacial p-type cell efficiencies by developing and implementing optimized homogeneous phosphorus (P) emitter on the front and tunnel oxide passivated boron (B) doped poly-Si contact (p-TOPCon) on the rear side, in combination with advanced fine-line screen-printing metallization and high bulk lifetime in the base material.

14 SOLAR ENERGY↗

DOE OSTI2021

Silver-carbon-nanotube composite metallization for increased durability of silicon solar cells against cell cracks

One of the ways to reduce the cost of solar electricity is to reduce the degradation rate of solar modules and extend their lifetime well beyond 30 years. The extended module lifetime translates to increased bankability of utility-scale PV projects. In this work, we specifically address cell-crack-induced degradation by introducing crack-tolerant metallization. Herein, we make use of low-cost, multi-walled carbon nanotubes embedded in commercial screen-printable silver pastes as a highly integratable engineering solution. When the carbon nanotubes are appropriately functionalized and incorporated into commercial silver pastes, the resulting metal contacts on solar cells, after screen-printing and firing, show exceptional fracture toughness. These composite metal contacts possess increased ductility, electrical gap-bridging capability greater than 50 µm, and “self-healing” to regain electrical continuity even after cycles of complete electrical failure under large strain. While providing crack-tolerant mechanical properties, the composite paste delivers similar beginning-of-life cell performance as the conventional silver paste.

14 SOLAR ENERGY↗