Engineering Papers⌕ Search

Engineering topics

Unocic, Raymond R.

Publications and source records attributed to Unocic, Raymond R..

142 records · Page 8

Creep Deformation of Allvac 718Plus

The creep deformation behavior of Allvac 718Plus was studied over the temperature range 650° to 732°C at initial applied stress levels ranging from 517 to 655 MPa. Over the entire experimental temperature stress regime this alloy exhibits Class M type creep behavior with all creep curves exhibiting a decelerating strain rate with strain or time throughout primary creep. However, unlike pure metals or simple solid solution alloys this gamma prime strengthened superalloy does not exhibit steady state creep. Rather, primary creep is instantly followed by a long duration of accelerating strain rate with strain or time. These creep characteristics are common amongst the gamma prime strengthened superalloys. Allvac 718Plus also exhibits a very high temperature dependence of creep rate. Detailed TEM examination of the deformation structures of selected creep samples reveals dislocation mechanisms similar to those found in high volume fraction gamma prime strengthened superalloys. Strong evidence of microtwinning is found in several of the deformation structures. The presence of microtwinning may account for the strong temperature dependence of creep rate observed in this alloy. In addition, due to the presence of Nb and thus, grain boundary delta phase, matrix dislocation activity which is not present in non Nb bearing superalloys occurs in this alloy. The creep characteristics and dislocation mechanisms are presented and discussed in detail.

36 MATERIALS SCIENCE↗

Direct Visualization of Solid Electrolyte Interphase Formation in Lithium-Ion Batteries with In Situ Electrochemical Transmission Electron Microscopy

Complex, electrochemically driven transport processes form the basis of electrochemical energy storage devices. The direct imaging of electrochemical processes at high spatial resolution and within their native liquid electrolyte would significantly enhance our understanding of device functionality, but has remained elusive. In this work we use a recently developed liquid cell for in situ electrochemical transmission electron microscopy to obtain insight into the electrolyte decomposition mechanisms and kinetics in lithium-ion (Li-ion) batteries by characterizing the dynamics of solid electrolyte interphase (SEI) formation and evolution. Here we are able to visualize the detailed structure of the SEI that forms locally at the electrode/electrolyte interface during lithium intercalation into natural graphite from an organic Li-ion battery electrolyte. We quantify the SEI growth kinetics and observe the dynamic self-healing nature of the SEI with changes in cell potential.

25 ENERGY STORAGE↗

Bis(fluoromalonato)borate (BFMB) anion based ionic liquid as an additive for lithium-ion battery electrolytes

Propylene carbonate (PC) is a good solvent for lithium ion battery applications due to its low melting point and high dielectric constant. But, PC is easily intercalated into graphite causing it to exfoliate, killing its electrochemical performance. We report on the synthesis of a new ionic liquid electrolyte based on partially fluorinated borate anion, 1-butyl-1,2-dimethylimidazolium bis(fluoromalonato)borate (BDMIm.BFMB), which can be used as an additive in 1 M LiPF6/PC electrolyte to suppress graphite exfoliation and improve cycling performance. Additionally, both PC and BDMIm.BFMB can be used synergistically as additive to 1.0M LiPF6/methyl isopropyl sulfone (MIPS) to dramatically improve its cycling performance. It is also found that the chemistry nature of the ionic liquids has dramatic effect on their role as additive in PC based electrolyte.

25 ENERGY STORAGE↗

Defect chemistry of phospho-olivine nanoparticles synthesized by a microwave-assisted solvothermal process

Nanocrystalline LiFePO{sub 4} powders synthesized by a microwave-assisted solvothermal (MW-ST) process have been structurally characterized with a combination of high resolution powder neutron diffraction, synchrotron X-ray diffraction, and aberration-corrected HAADF STEM imaging. A significant level of defects has been found in the samples prepared at 255 and 275 °C. These temperatures are significantly higher than what has previously been suggested to be the maximum temperature for defect formation in LiFePO{sub 4}, so the presence of defects is likely related to the rapid MW-ST synthesis involving a short reaction time (∼5 min). A defect model has been tentatively proposed, though it has been shown that powder diffraction data alone cannot conclusively determine the precise defect distribution in LiFePO{sub 4} samples. The model is consistent with other literature reports on nanopowders synthesized at low temperatures, in which the unit cell volume is significantly reduced relative to defect-free, micron-sized LiFePO{sub 4} powders. - Graphical abstract: Temperature-dependent antisite defect formation has been observed in nanocrystalline LiFePO{sub 4} powders synthesized by a microwave solvothermal process, using high resolution diffraction and STEM imaging. Display Omitted - Highlights: • LiFePO{sub 4} nanopowders synthesized by a microwave-assisted solvothermal process. • Defects directly observed by aberration-corrected HAADF STEM imaging. • Antisite defects present from synthesis at 255 and 275 °C. • Defects present from higher temperature synthesis than previously reported. • Powder diffraction data have been analyzed in detail for various defect models.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Solid electrolyte coated high voltage layered–layered lithium-rich composite cathode: Li 1.2 Mn 0.525 Ni 0.175 Co 0.1 O 2

We find that the electrochemical rate performance and capacity retention of the “layered–layered” lithium rich Li 1.2 Mn 0.525 Ni 0.175 Co 0.1 O 2 (Li-rich NMC) material are significantly improved by a nanometer layer coating of a lithium conducting solid electrolyte, lithium phosphorus oxynitride (LiPON). The LiPON layer is deposited on the Li-rich NMC particles by the RF-magnetron sputtering method. The presence of the LiPON layer provides interfacial stability under high current (rate) and voltage cycling conditions and thereby improves the capacity retention over cycle life compared to pristine or uncoated Li-rich NMC. Specifically, the LiPON coated Li-rich NMC composite electrode showed stable reversible capacities of >275 mAh g -1 when cycled to 4.9 V for more than 300 cycles, and showed at least threefold improvements in the rate performance compared to the uncoated electrode compositions. Increasing the LiPON layer thickness beyond a few nanometers leads to capacity fade due to increasing electronic resistance. Lastly, detailed microstructural and electrochemical impedance spectroscopy studies are undertaken to characterize and understand the role of LiPON in improving the interfacial stability and electrochemical activity at the interface.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Direct exfoliation of natural graphite into micrometre size few layers graphene sheets using ionic liquids

Stable high-concentration suspensions (up to 0.95 mg mL -1 ) of non-oxidized few layer graphene (FLG), five or less sheets, with micrometre-long edges were obtained via direct exfoliation of natural graphite flakes in ionic liquids, such as 1-butyl-3-methyl-imidazolium bis(trifluoro-methane-sulfonyl)imide ([Bmim]-[Tf 2 N]), by tip ultrasonication.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗