Engineering Papers⌕ Search

Engineering topics

Tyler Hudson

Publications and source records attributed to Tyler Hudson.

17 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2024

Dynamic Mechanical Analysis of Post-Cured Bismaleimide Resins for Composite-Overwrapped Combustion Chambers Cycled From Cryogenic to High Temperatures

In support of the Rapid Analysis and Manufacturing Propulsion Technology (RAMPT) project, samples made of polybismaleimide (BMI) resin were made and tested under cryogenic conditions. Neat resin samples were tested for multiple cycles, from high temperature (300°C) to cryogenic temperature (-150°C), to replicate the conditions a rocket engine assembly would experience in a test campaign and in operation. To increase the glass transition temperature (and thus mechanical stability), samples were exposed to different post-cure temperatures and were tested using a dynamic mechanical analysis (DMA) instrument. Consistent with expectations, the BMI samples post-cured at higher temperatures generally resulted in higher storage modulus under high temperature test conditions but at the expense of storage modulus values at low temperature test conditions.

Christopher Stelter↗
NASA NTRSDate not supplied

CAS: AERoBOND Overview

Explore the source record for details and available documents.

Frank Palmieri↗
NASA NTRSDate not supplied

Lightweight Thrust Chamber Composite Overwrap Lessons Learned

The manufacturing, design, and analysis of filament wound carbon fiber/polymer composite overwraps for additively manufactured, copper combustion chambers are a critical part of NASA’s Rapid Analysis and Manufacturing Propulsion Technology (RAMPT) project. Ideally, the composite overwrap acts as a light-weight structural jacket and allows significant weight reduction of the high pressure thrust chamber assembly, reduction of overall cost, and reduced fabrication schedules. Chamber assemblies for 2000 lb. (2k) and 7000 lb. (7k) of thrust have been successfully tested at NASA’s Marshall Space Flight Center. Multiple lessons were learned throughout the overwrap process development and manufacturing trials. The lessons learned on small scale hardware, such as the 2k and 7k chambers, will guide further composite manufacturing technologies and enable a progression to larger scale assemblies with greater structural loads. Material performance requirements, manufacturing process development, and surface preparation were evaluated during the small chamber trials, with the broad thermal requirements of the resin being the primary driver for material selection and processing. Both epoxy and bismaleimide (BMI) materials were evaluated with respect to both performance in the hot-fire test and ease of fabrication. Separately, surface preparation procedures were studied with the goal of providing a smooth chamber surface to promote a non-bonded overwrap. Recent testing of the 7k trust chamber has provided data in Non-Destructive Evaluation (NDE) and processing in order to continue to evaluate the performance requirements stated.

Allison Clark↗
NASA NTRSDate not supplied

Composite Bond Line Measurements Based on a Bayesian Analysis of Flash Thermography Data

For bonded composite materials, an accurate characterization of the adhesive bond line is needed to predict failure modes and fracture toughness. In this paper, bond line thickness was estimated from data obtained using through transmission flash thermography. The forward model that predicts back surface temperature is based on a three layer heat diffusion equation with varying diffusivity and flux boundary conditions. The corresponding inverse problem of estimating bond line thickness from measurement data was solved using a Bayesian approach that assumed Gaussian priors for the bond line thickness and thermal diffusivity of the adherends. Finally, the outputs of the thermography based method were compared to measurements that were collected using a micrometer and ultrasound testing.

Flash thermography↗
NASA NTRSDate not supplied

Sources of Uncertainty in Ultrasonic Phase-Based Assessment of Interfacial Stiffness in Adhesive Joints

Quantitative nondestructive evaluation (NDE) of adhesive joint strength is critical for certifying fastener-free bonded aerospace structures. Unfortunately, available adhesive NDE approaches are only suitable for detecting gross defects and delamination and cannot reliably detect variations in strength in intact bonds. Intact (i.e., nominally defect free) bonds are challenging to inspect because they, by definition, contain no macroscopic defects that would produce a strong NDE signature. Even in the absence of obvious defects, however, bond strength can vary substantially due to factors such as contamination, variations in the adhesive cure processes, and environmental exposure. For ultrasonic bond inspections, the effect of interactions from an imperfect adhesive interface are subtle and may include changes in the frequency content or phase of the ultrasonic signal. The bond condition can be deduced from these subtle changes in the acoustic response using an accompanying physics-based model of adhesive joint interaction. For example, researchers have used the spring network adhesion model of Baik and Thompson [1] to determine the interfacial stiffness of the joint from its ultrasonic response (e.g., [2]). This interfacial stiffness metric describes the bonds resistance to separation between the adhesive and adherent and has shown a strong correlation with joint strength. In this study, interfacial stiffness is assessed using the ultrasonic phase change associated with bond interaction in varying bond conditions. The phase change is measured precisely using a phase-locked-loop instrument over a swept range of frequencies. The phase transition at resonance, where the bond thickness is half the acoustic wavelength, produces a unique signature with which to fit a physics-based model. Interfacial stiffness is determined by minimizing the difference between the theoretical and experimental phase response. Experimental results are presented for glass specimens bonded with aerospace adhesives and a sensitivity analysis is performed to examine the effects of parameters that may be uncertain in the industrial inspection environment – namely bond thickness, adhesive and adherent properties, and porosity. The results are a first step toward an uncertainty quantified version of the measurement technique, show correlation between interfacial stiffness and bond strength, and are another key step toward maturing this approach for use in complex materials and joint geometries. [1] Baik, J.M. and Thompson, R.B., 1984. “Ultrasonic scattering from imperfect interfaces: a quasi-static model”. Journal of Nondestructive Evaluation, 4. [2] Haldren, H.A., Perey, D.F., Yost, W.T., Cramer, K.E., and Gupta, M.C., 2019. “Swept-frequency ultrasonic phase evaluation of adhesive bonding in tri-layer structures”. Journal of the Acoustical Society of America, 145.

Matt Webster↗