Engineering Papers⌕ Search

Engineering topics

Tumuluru, Jaya Shankar

Publications and source records attributed to Tumuluru, Jaya Shankar.

10 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Mitigating municipal solid waste fouling in biofuel conversion via screw surface modifications

Here, municipal solid waste (MSW)'s 40–60 % carbon content makes it a feedstock for biofuel production via pyrolysis. One challenge in the conversion process is MSW fouling due to thermal decomposition. The accumulated deposit on the injection screw often leads to plugging and constriction. This study examined the morphology and composition of the MSW fouling deposit and conducted a thermal simulation to understand the temperature gradience of the injection screw. Surface modifications including smoothening and anti-adhesion coating were proposed for the injection screw to address the deposit problem. For evaluating the candidate mitigations, a bench-scale fouling test was developed with the gas environment, temperature, and sliding speed relevant to the contact interface between the MSW particles and the screw. Results suggested that a smoother screw surface could reduce the grip and a non-metallic coating with a lower surface energy could decrease adhesion, consequently leading to less fouling. Specifically, reducing the roughness from 2 to 0.6 and then to 0.2 μm proportionally decreased the amount of deposit, and the diamond-like-carbon, CrN, and NiCr–CrC composite coatings effectively hindered the fouling process. This study provides fundamental insights into the MSW fouling and proof-of-concept of potential mitigations through the screw surface modification.

09 BIOMASS FUELS↗
DOE OSTI2023

Grinding and Pelleting Characteristics of Municipal Solid Waste Fractions

The efficient utilization of low-cost carbon feedstocks, such as municipal solid waste (MSW), in biorefineries has become increasingly important for reducing GHG emissions and meeting the growing demand for renewable energy sources. However, MSW as a feedstock presents several challenges, including high moisture content, compositional variability, particle size and shape, density, and ash content. To address these challenges, the potential of mechanical dewatering and high-moisture pelleting processes for densifying MSW fractions, such as paper, cardboard, thin plastic, and thick plastic, into low-cost carbon feedstocks with improved handling and conversion properties were investigated. The effect of these preprocessing technologies on the critical quality attributes (CQAs) of the resulting pellets, including bulk density, durability, and size uniformity, were evaluated. The results showed that with these preprocessing technologies, the paper and cardboard fractions could be pelleted at moisture contents over 40% (w.b.) while achieving >99% durability and >300 kg/m3, while the high moisture plastic fractions were not suitable for pelleting. The thick plastic fraction processed in a screw press was shown to remove up to 30% of the moisture content in a single pass. These findings suggest that these mechanical preprocessing technologies can improve the physical properties of low-cost municipal solid waste fractions for biofuels production.

09 BIOMASS FUELS↗
DOE OSTI2023

High-moisture pelleting of corn stover using pilot- and commercial-scale systems: Impact of moisture content, L / D ratio and hammer mill screen size on pellet quality and energy consumption

Here, high-moisture pelleting of corn stover was tested in pilot- and commercial-scale systems. For the pilot-scale study, a 6.35 mm screen size hammer mill ground corn stover was reconditioned to moisture between 14 and 29.6% (w.b.), and 5, 7 and 9 L/D ratio pellet die were used. At 29% corn stover moisture content and L/D ratios of 5 and 9, the bulk density and durability of the pellets were ≤450 kg/m 3 and <90% and >540 kg/m 3 and >90%, respectively. Increasing the feedstock moisture and L/D ratio increased the pelleting energy. Increasing the hammer mill screen size to 11.11 mm reduced the bulk density but not the durability. The response surface models adequately described the pelleting process (R 2 ≥ 0.88), and analysis of variance showed a strong interaction between the process variables and pellet properties. Commercial-scale testing of high-moisture pelleting using 6.35 mm ground corn stover bales in the moisture range 24–26% (w.b.) produced pellets with a density of >675 kg/m 3 and durability of >98%, whereas increasing the hammer mill screen size to 11.11 mm reduced the bulk density by about 100 kg/m 3 but not the durability. The energy consumption of the commercial-scale unit operations for the high-moisture pelleting process was in the range 98–124 kW h/ton, which is 64–72% less energy than conventional pelleting that requires energy about 350 kW h/ton for biomass drying from 30% (w.b.) to 10% (w.b.) moisture content before pelleting. Pellets produced using high-moisture pelleting met International Organization for Standardization and Pellets Fuel Institute international standards. Published 2023. This article is a U.S. Government work and is in the public domain in the USA.

09 BIOMASS FUELS↗
DOE OSTI2022

Methods of forming densified biomass

A method includes densifying a biomass feedstock having a moisture content of at least about 30% by weight and drying the biomass feedstock to form a densified biomass having a moisture content of less than about 10% by weight. Some methods include comminuting a biomass feedstock, pressing the biomass feedstock to form a plurality of pellets, heating the plurality of pellets to remove water therefrom, and cooling the plurality of dried pellets. The plurality of pellets exhibits a moisture content of at least about 20% by weight after pressing. The plurality of dried pellets exhibits a moisture content of less than about 10% by weight. A system for forming densified biomass may include a preheater, a press, and a dryer.

09 BIOMASS FUELS↗
DOE OSTI2022

Pilot-Scale Pelleting Tests on High-Moisture Pine, Switchgrass, and Their Blends: Impact on Pellet Physical Properties, Chemical Composition, and Heating Values

In this study, we evaluated the pelleting characteristics of southern yellow pine (SYP), switchgrass (SG), and their blends for thermochemical conversion processes, such as pyrolysis and gasification. Using a pilot-scale ring-die pellet mill, we specifically assessed the impact of blend moisture, length-to-diameter (L/D) ratio in the pellet die, and ratio of pine to SG on the physico-chemical properties of the resulting pellets. We found that an increase in pine content by 25–50% marginally affected the bulk density; however, it also led to an increase in calorific value by 7% and a decrease in ash content by 72%. A moisture content of 25% (wet basis) and an L/D ratio of 5 resulted in poor pellet durability at <90% and bulk density values of <500 kg/m 3 , but increasing the L/D ratio to 9 and lowering the moisture content to 20% (w.b.) improved the pellet durability to >90% and the bulk density to >500 kg/m 3 . Blends with ≥50% pine content resulted in lower energy consumption, while a lower L/D ratio resulted in higher pelleting energy. Based on these findings, we successfully demonstrated the high-moisture pelleting of 2.5 ton of pine top residues blended with SG at 60:40 and 50:50 ratios. The quality of the pellets was monitored off-line and at-line by near infrared (NIR) spectroscopy. Multivariate models constructed by combining the NIR data and the pelleting process variables could successfully predict the pine content (R 2 = 0.99), higher heating value (R 2 = 0.98), ash (R 2 = 0.95), durability (R 2 = 0.94), and bulk density (R 2 = 0.86) of the pellets. Thus, we established how blending and densification of SYP and SG biomass could improve feedstock specifications and that NIR spectroscopy can effectively monitor the pellet properties during the high-moisture pelleting process.

09 BIOMASS FUELS↗
DOE OSTI2021

Explore the Potential to Formulate Feedstock Blends from Diverse Biomass inputs for Improved Processing Performance at Lower Costs

This work aims to understand the pelleting characteristics of 2-inch top-pine residue blended with switchgrass at high moisture content. The process variables tested are blend moisture content, length-to-diameter (L/D) ratio in the pellet die, and the blend ratio. A flat-die pellet mill was also used in this study. The pine and switchgrass blend ratios that were tested include (1) 25% 2-inch top pine residue with 75% switchgrass; (2) 50% 2-inch top pine residue with 50% switchgrass; and (3) 75% 2-inch top pine residue with 25% switchgrass. The pelleting process conditions tested included the L/D ratio in the pellet die (i.e., 1.5 to 2.6) and the blend moisture content (20 to 30%, w.b.). Analysis of experimental data indicated that blending 25% switchgrass with 75% 2-inch top pine residue and 50% switchgrass with 50% 2-inch top pine residue resulted in pellets with a bulk density of >550 kg/m3 and durability of >95. Optimization of the response surface models developed for process conditions in terms of product properties indicated that a higher L/D ratio of 2.6 and a lower blend-moisture content of 20% (w.b.) maximized bulk density and durability. Higher pine in the blends improved the pellet durability and reduced energy consumption. Tests were also conducted on blends of pine and switchgrass using a pilot scale pellet mill by varying the blend moisture content and compression ratio of the pellet die. Pelleting tests on pure pine and switchgrass and their blends in a pilot scale ring die pellet mill with a throughput of 1 ton/h has indicated pellets with durability >500 kg/m3 and durability in the range of >90 and >95 %. The demonstration of high moisture pelleting of blends of 2- and 6-inch top pine residues and switchgrass blends indicated that good quality pellets with durability >90 % and bulk density of >500 kg/m3 can be produced.

09 BIOMASS FUELS↗
DOE OSTI2021

FCIC DFO--Moisture Management and Optimization in Municipal Solid Waste Feedstock through Mechanical Processing

The project goal is to produce densified product, focusing on characteristics of bulk density, durability, and moisture content, to reduce the cost of preprocessing. The objective of the project is to efficiently manage and handle the properties of MSW feedstock through INL-developed fractional milling, high moisture pelleting, and low temperature drying preprocessing technologies .

09 BIOMASS FUELS↗
DOE OSTI2021

Biomass Size Reduction, Drying, and Densification

The overall objective is to solve the particle attrition issue during biomass grinding and pelleting and to enable pelleting as a viable option for production of on-spec material or conversion-ready cellulosic feedstocks.

09 BIOMASS FUELS↗