Engineering topics

Tucker, Michael C.

Publications and source records attributed to Tucker, Michael C..

7 records

DOE OSTI2025

Voltage cycling as a dynamic operation mode for high temperature electrolysis solid oxide cells

Solid Oxide Electrolysis Cells (SOECs) have emerged as a promising technology for the efficient production of H2 via high-temperature electrolysis. However, power input from dynamic energy sources remains a significant challenge for their long-term stability. It is important to analyze the tolerance of cells under dynamic operation conditions. This study focuses on evaluating the impact of voltage cycling on the performance and durability of electrode-supported SOECs. We explore the operational limits and degradation mechanisms of SOECs subjected to various voltage conditions and find that the cells have high tolerance for dynamic voltage. Voltage cycling between 1.3 V and 1.5 V for 9000 cycles does not damage the cell. Conversely, cycling to higher voltages (≥1.7 V) results in accelerated degradation. Advanced characterization is used to screen for various degradation modes post operation. Within the oxygen electrode, XRD and STEM EDS find compositional and phase evolution in all voltage cycled samples including increased decomposition of the air electrode resulting in cation migration. Microstructural analysis of the fuel electrode from nano-CT data shows minimal change throughout the sample set and no evidence of Ni migration, indicating the fuel electrode is stable and not impacted by cycling to higher voltages within the timeframe studied.

Zhu, Zhikuan↗

DOE OSTI2024

Microscale mechanical property variations of Al-substituted LLZO: insights from compression testing and molecular dynamics simulations

Ceramic solid electrolytes based on LLZO (Li 7 La 3 Zr 2 O 12 ) are promising candidates for all-solid-state batteries due to their high ionic conductivity and good apparent stability vs. lithium metal, however they are prone to mechanical failure. Lithium metal intrusions, alongside cell stack pressure, transition polycrystalline solid electrolyte grains into a compressed state that promotes crack propagation and fracture. Here this work examines the mechanical response of Al-substituted LLZO to compressive forces by measuring ultimate strength under pillar compression with a flat punch tip. Failure modes characterized by in situ scanning electron microscopy show diverse splitting patterns arising from internal porosity, grain boundaries, and slip planes. Large correlated variations in compressive strength (0.93–2.63 GPa) and Young's modulus (72.1–150.97 GPa) are observed across microscale regions of the solid electrolyte. Molecular dynamics simulations of LLZO with different porosities describe the variation of compressive strength and Young's modulus, and enable a microscale porosity model to be fit accounting for Young's modulus reduction across the solid electrolyte. Overall, the results indicate the importance of microscale mechanical testing of ceramic solid electrolytes to identify preferential sites for mechanical degradation and Li intrusion, and ensure the robust design of all-solid-state lithium metal batteries.

25 ENERGY STORAGE↗

DOE OSTI2024

Simple processing via thermal treatment and catalyst infiltration to enhance nickel electrode performance for liquid alkaline water electrolyzers

Two simple processes for enhancing liquid alkaline water electrolyzer performance are demonstrated. Both enhance 3D Ni electrodes by introducing a micron-scale rough structure throughout the bulk of the electrode. Oxidation/reduction relies on a simple thermal treatment cycle to create surface roughening through the volumetric expansion during NiO formation and volume contraction during reduction back to Ni metal. Catalyst infiltration introduces a washcoat of additional metal particles throughout the electrode, by flooding the electrode with catalyst precursor and converting it to micron-scale particles via a reducing thermal treatment. Further, the largest improvement in performance (211mV at 1.8Acm -2 ) is observed for infiltrated NiFe-3x catalyst. For Fe-free Ni-only electrodes, oxidation/reduction provides a larger improvement (157 mV at 1.8Acm -2 ) than infiltrated Ni-3X (106mV at 1.8Acm -2 ). For both processes, the observed electrode surface structure and performance is quite sensitive to the thermal treatment temperature.

08 HYDROGEN↗

DOE OSTI2024

Pioneering Microporous Layers for Proton-Exchange-Membrane Water Electrolyzers via Tape Casting

The imperative shift towards decarbonization necessitates the production of clean hydrogen through water electrolysis, powered by renewable energy sources. Among electrolyzer technologies, proton-exchange-membrane (PEM) systems emerge as a promising option for large-scale hydrogen generation due to their modular design and rapid response, aligning well with the intermittency of renewable energy. In this study, we employ a tape casting method to fabricate microporous layers (MPLs), both as a single layer and as a bilayer over commercial porous transport layers (PTLs), to further enhance performance of water electrolyzers. We demonstrate that microporous layers require adequate pore sizes to facilitate gas removal, preventing gas flooding and preserving electrolyzer performance. Our single layer microporous layers exhibit lower overpotentials compared to commercial sintered Ti PTLs by 142 mV at 4 A·cm ⁻2 . Moreover, we show that having an effective microporous layer enhances electrolyzer performance irrespective of the substrate used, offering avenues for cost reduction. We also investigate novel PTL structures with reduced tortuosity and integrated MPL fabricated via phase inversion tape casting, resulting in a performance enhancement of 92 mV. Our findings unravel the critical role of microporous layer structures and their impact on electrolyzer performance.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2024

Scalable Surface Micro-Texturing of LLZO Solid Electrolytes for Battery Applications

A challenge for lithium lanthanum zirconate (LLZO)-based solid-state batteries is to increase the critical current density (CCD) to enable high current cycling. A promising strategy is to modify the LLZO surface morphology to provide a larger contact area with the Li metal. Here, a surface-textured thin LLZO electrolyte was prepared through an easily scalable process. The texturing process is a simple pressing of green LLZO tapes between micro-textured substrates. A variety of textures can be produced, depending on the type of substrate, and texturing can be on either one side or both sides. For this work, after pressing and sintering, several micro-patterns are formed on thin LLZO (~118 μm thick). The properties of the various samples were characterized to investigate the impact of surface texturing, and the most promising ones were selected for electrochemical testing in symmetrical lithium cells and full cells. Li symmetric cells using a coarse ridge-textured LLZO exhibit ~2.5 times increased CCD compared to planar non-textured LLZO, and a solid-state full cell shows stable cycling and improved rate performance. Finally, we believe this process offers a favorable trade-off of processing complexity vs structural optimization to maximize CCD.

25 ENERGY STORAGE↗

DOE OSTI2024

Succinonitrile-Lithium Salt Complexes as Solid Catholytes for LLZO-Based Solid-State Batteries

The thermal and electrochemical properties of several succinonitrile (SN)-based organic ionic plastic crystals (OIPCs) containing lithium bis(trifluoromethanesulfonyl)imide (LiTFSI), lithium bis(oxalate) borate (LiBOB) or mixtures of the two salts, were investigated with the goal of determining which is most promising for use as a catholyte in solid-state lithium batteries. The best combination of properties for this use was found for the mixture containing 3 mol% LiTFSI and 2 mol% LiBOB in SN. Based on these observations, several solid-state cells containing Al-substituted Li 7 La 3 Zr 2 O 12 separators with composite cathodes consisting of LiNi 0.33 Mn 0.33 Co 0.33 O 2 (NMC111), carbon black, and the succinonitrile-salt mixtures were assembled and cycled at room temperature, without exogenous pressure, using a simple design.

25 ENERGY STORAGE↗

DOE OSTI2024

Dynamic operation of metal-supported solid oxide electrolysis cells

Symmetric-structure metal-supported solid oxide fuel cells and electrolysis cells (MS-SOFCs, MS-SOECs) offer several advantages over conventional solid oxide cells, including the use of inexpensive materials, high mechanical strength, and rapid ramp-up ability. Aggressive operation of MS-SOCs in fuel cell mode is well-established, including extremely fast start-up, redox tolerance, and imbalanced pressure. Here, we extend dynamic operation to MS-SOCs in SOEC mode with high steam content for both small button cells and a large rectangular cell, including: steam cycling, thermal cycling, redox cycling and power cycling. Steam cycling entailed switching between 3:97 and 50:50 steam:hydrogen ratio. For thermal cycling, the temperature was rapidly varied between 150°C and 700°C for 50 cycles. Redox cycling involved switching the steam side gas between 50 % humidified H 2 and 50 % humidified N 2 for 5 cycles. Power cycling was performed by operating the cell under variable current density, resulting in cell voltage between 1.3V and 2.8V. Degradation rates for each testing strategy were compared to a baseline cell, and found to be similar. In conclusion, the excellent tolerance to dynamic operation increases confidence that MS-SOECs will be compatible with dynamic or intermittent renewable resources.

08 HYDROGEN↗