Engineering Papers⌕ Search

Engineering topics

Trbojevic, D.

Publications and source records attributed to Trbojevic, D..

At least 37 records · Page 2

Beam Commissioning Results from the CBETA Fractional Arc Test (CBETA Note 030)

This work describes first commissioning results from the Cornell Brookhaven ERL Test Accelerator fractional arc test. These include the recommissioning of the Cornell photoinjector, the first full energy operation of the main linac with beam, as well as commissioning of the lowest energy matching beamline (splitter) and a partial section of the Fixed Field Alternating gradient (FFA) return loop featuring first production Halbach style permanent magnets. Achieving these tasks required characterization of the injection beam, calibration and phasing of the main linac cavities, demonstration of the required 36 MeV energy gain, and measurement of the splitter line horizontal dispersion and R 56 at the nominal 42 MeV. In addition, a procedure for determining the BPM offsets, as well as the tune per cell in the FFA section via scanning the linac energy and inducing betatron oscillations around the periodic orbit in the fractional arc was developed and tested. A detailed comparison of these measurements to simulation is discussed.

43 PARTICLE ACCELERATORS↗

Equipment Protection System for CBETA

The ultimate goal of CBETA is to be the first high-current multi turn Energy Recovery Linac operating at 40 mA. The power of highest energy beam at this configuration is going to be 6 MW. Hence equipment protection against radiation is an important issue. Through our stages of commissioning we will slowly increase the beam current, starting from 100 pA all the way to 1 mA during the current commissioning phase. The electron beams hitting any in-vacuum component either on purpose (e.g. view screens, beam stops or during commissioning) or due to some component failure will generate a radiation shower which has the potential to damage various parts of the accelerator. In this document, we describe the various scenarios which generate unwanted radiation in our machine and list the damage thresholds of critical components. Then we discuss our diagnostic systems which can detect component failure and the resulting radiation generated. We further list the possible beam modes of the machine which we have designed taking into account the damage thresholds and the sensitivity of the diagnostics. Finally, we document our design of the Equipment Protection System (EPS) and outline protocols of calibration and operation.

43 PARTICLE ACCELERATORS↗

Beam dynamics validation of the Halbach Technology FFAG Cell for Cornell-BNL Energy Recovery Linac

The Cornell-BNL Electron Test Accelerator (CBETA), a 150 MeV energy recovery linac (ERL) now in construction at Cornell, employs a fixed-field alternating gradient optics return loop: a single beam line comprised of FFAG cells, which accepts four recirculated energies. CBETA FFAG cell uses Halbach permanent magnet technology, its design studies have covered an extended period of time supported by extensive particle dynamics simulations using computed 3-D field map models. As a result, this approach is discussed, and illustrated here, based on the final stage in these beam dynamics studies, namely the validation of a ultimate, optimized design of the Halbach cell.

43 PARTICLE ACCELERATORS↗

Beam dynamics validation of the Halbach Technology FFAG Cell for Cornell-BNL Energy Recovery Linac

The Cornell-BNL Electron Test Accelerator (CBETA), a 150 MeV energy recovery linac (ERL) now in construction at Cornell, employs a fixedfield alternating gradient (FFAG) optics return loop: a single beam line comprised of quadrupole doublet cells, which accepts four recirculated energies. CBETA FFAG cell uses Halbach permanent magnet technology, its design studies have covered an extended period of time supported all the way by extensive particle dynamics simulations using computed 3-D field map models. This approach, which supported the choice of Halbach technology for CBETA FFAG ERL in 2016, is discussed and illustrated here based on the final stage in these beam dynamics studies, namely the validation of a ultimate, optimized design of the cell.

43 PARTICLE ACCELERATORS↗

Design of a modified Halbach magnet for the CBETA Project

A modified Halbach magnet has been designed to be installed in the splitter/merger section of the CBETA project which is under construction at Cornell University. The splitter/merger of the CBETA consists of 4 beam lines and is shown in Fig. 1. Two of the functions of the splitter/merger lines are; first to match the beam parameters at the exit of the Energy Recovery Linac (ERL) to those at the entrance of the Fixed Field Alternating Gradient (FFAG) arc, and second to place the trajectories of the reference particles of the beam bunches at the entrance of the FFAG arc on specified trajectories as they determined by the beam optics of the FFAG arc. In this technical note we present results from the 2D and 3D electromagnetic analysis of the S4.BEN01 magnet which is one of the dipole magnets of the 150 MeV line of the splitter/merger. The present design of the S4.BEN01 magnet, is based on a modified Halbach-type permanent magnet. To justify our suggestion of using a Halbach type of magnet instead of an electromagnet for the S4.BEN01 magnet we devote an APPENDIX A in which we provide details on the design of an electromagnet for the S4.BEN01 magnet and in the section under conclusion will list the pros and cons of the two designs.

43 PARTICLE ACCELERATORS↗

CBETA Design Report

This Design Report describes the baseline design of the Cornell-BNL ERL Test Accelerator, as it exists on the date of its publication in June 2017. The Design Report will not change frequently in the future. In contrast, the parameter sheets that summarize the CBETA design will respond as quickly and as thoroughly as necessary to maintain con guration control.

43 PARTICLE ACCELERATORS↗

CBETA Design Report

This Design Report describes the baseline design of the Cornell-BNL ERL Test Accelerator, as it exists on the date of its publication in June 2017. The Design Report will not change frequently in the future. In contrast, the parameter sheets that summarize the CBETA design will respond as quickly and as thoroughly as necessary to maintain configuration control.

43 PARTICLE ACCELERATORS↗

TM 2: Assembly prototype girder

This Technical Note presents details of the successful achievement of Technical Milestone 2 in the NYSERDA contract with Brookhaven National Laboratory and Cornell University. The project { to design, build and commission the Cornell-BNL Electron Test Accelerator (CBETA) { will achieve final success when all 12 Technical Milestones are complete.

43 PARTICLE ACCELERATORS↗

Two design of the S4.BEN01 magnet for the CBETA splitter/merger

The splitter/merger section of the CBETA project [1] consists of 4 beam lines as shown in Fig. 1. Two of the functions of the splitter’s/merger’s lines is to match the beam parameters at the exit of the Energy Recovery Linac (ERL) to the beam parameters at the entrance of the Fixed Field Alternating Gradient (FFAG) arc, and also place the reference particles of the beam bunches at the entrance of the FFAG arc on specified trajectories according to their energies. In this technical note we are presenting results from the 2D and 3D electromagnetic analysis of the S4.BEN01 magnet which is one of the dipole magnets of the 150 MeV line of the splitter/merger. In particular we present results from two designs of the S4.BEN01 magnet, one based on iron dominated current-excited magnet, and the other design based on Halbach-type permanent magnet. An evaluation of the two designs will be given in the section under “conclusion”.

43 PARTICLE ACCELERATORS↗