Engineering Papers⌕ Search

Engineering topics

Trautwein, W.

Publications and source records attributed to Trautwein, W..

16 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1979

Operational loopwheel suspension systems for Mars Rover demonstration model: Loopwheel failure report

The results are presented from the analysis of a failure which occurred in the fiberglass loop of one of the Loopwheel traction elements delivered to the Jet Propulsion Laboratory (JPL) for use on the JPL Mars Rover demonstration model. The loop failed in compression in the outer fibers forming a hinge which, through cycling, caused the inner fibers to break. The probable cause of this failure was the load being introduced as point loads at the center of the loop causing high compressive stresses and early buckling. To decrease the stress level and delay buckling, the tread lugs can be reshaped so that the entire lug contacts the ground when the loop is loaded. This can be accomplished through removal of lug material, starting with zero removal at the outer edge and linearly increasing to one-half of the lug thickness at the center.

West, E. J. M.↗
NASA NTRS1978

Operational Loopwheel Suspension System for Mars Rover Demonstration Model

The loopwheel (or elastic loop) mobility concept, appears to be uniquely qualified to provide a high degree of mobility at low weight and stowage requirements for the next Mars mission now in the early planning stage. Traction elements compatible with sterilization and Mars surface environmental constraints were designed and are compatible with the rover mass, range and stowage requirements of JPL's point design Mars rover. In order to save cost, the loopwheel suspensions for the demonstration model were made of S-glass/epoxy instead of titanium, alloy specified for flight units. The load carrying fiberglass loop core is covered by a rubber tread on the outside. Reinforced rubber gear belts bonded along the inside edges provide positive engagement and transmission drive torques. A 12 Vdc drive motor with a 167:1 gear head is installed in the payload section of the hull. A chain drive transmits the motor power to the rear sprocket in the demonstration model, whereas future flight units would be directly driven by brushless hub motors within each sprocket and independent four-leg height control.

Trautwein, W.↗
NASA NTRS1977

Mars Rover system loopwheel definition support

The feasibility of the loopwheel suspension system for use on a Mars roving vehicle was analyzed. Various steering concepts were evaluated and an optimum concept was identified on the basis of maximum probability of mission success. In the structural analysis of the loopwheel core and tread as the major fatigue critical components, important technology areas were identified.

Trautwein, W.↗
NASA NTRS1976

A mobile planetary lander utilizing elastic loop suspension

Efforts to increase the cost effectiveness of future lunar and planetary rover missions have led to the mobile lander concept, which replaces the landing legs of a soft-lander craft with a compact mobility system of sufficient strength to withstand the landing impact. The results of a mobile lander conceptual design effort based on existing NASA-Viking '75 hardware are presented. The elastic loop concept, developed as a post-Apollo rover technology, is found to meet stringent stowage, traction, power and weight requirements.

Trautwein, W.↗
NASA NTRS1973

Articulated elastic-loop roving vehicles

Prototype vehicle features exceptional obstacle-negotiating and slope-climbing capabilities plus high propulsive efficiency. Concept should interest designers of polar or ocean-bottom research vehicles. Also, its large footprint and low ground pressure will minimize ecological damage on terrain with low bearing strength, as in off-the-road application.

Chang, C. J.↗
NASA NTRS1973

Control strategies for planetary rover motion and manipulator control

An unusual insect-like vehicle designed for planetary surface exploration is made the occasion for a discussion of control concepts in path selection, hazard detection, obstacle negotiation, and soil sampling. A control scheme which actively articulates the pitching motion between a single-loop front module and a dual loop rear module leads to near optimal behavior in soft soil; at the same time the vehicle's front module acts as a reliable tactile forward probe with a detection range much longer than the stopping distance. Some optimal control strategies are discussed, and the photos of a working scale model are displayed.

Trautwein, W.↗
NASA NTRS1972

Design, fabrication and delivery of an improved single Elastic Loop Mobility System (ELMS)

Several significant design improvements have been incorporated into the second-generation full-scale ELMS unit. A major improved design accomplishment was the increase of the load carrying capacity of elastic loops without severe weight or stress penalties. Redesign of the loop form and size, plus selection of a more advanced titanium alloy, resulted in performance characteristics representing a marked improvement over the first-generation unit. Another important design improvement was the shaping of the loop's footprint into a favorable form for uniform pressure distribution. Other improvements are associated with a more efficient drive torque transmission from the internal drive drums to the elastic loop which are expected to reduce the internal losses of the drive system. The new ELMS unit will be capable of being integrated, on a modularized basis, with a multi-loop articulated ELMS test vehicle as the next logical step in the development of the mobility concept.

Trautwein, W.↗
NASA NTRS1972

The application of optimal control technqiues to advanced manned missions, volume 1

Two problems are presented in the area of optimal control and its application to the design of attitude control systems for advanced complex aerospace vehicles. The problems discussed are specification of performance criteria in terms of structural load minimization and/or maximum orbital payload injection requirements of the controlled vehicle; and formulation and solution of the optimization problem such that practical control systems are obtained.

Connor, C. L.↗
NASA NTRS1972

The application of optimal control techniques to advanced manned missions, volume 2

The hybrid optimization techique for attitude control design is described in detail. The technque is capable of optimizing an n-dimensional adjustable parameter vector, but a 1-dimensional vector is used as an example to explain the procedure. This permits an easier explanation as opposed to a multidimensional case. The procedure used to derive the perturbation equations of motion describing the 6-DOF shuttle ascent phase is presented. These equations were programmed on the EAI 8800 analog computer to describe the perturbations of the shuttle vehicle from a nominal zero lift trajectory due to wind disturbances. Included are the control system equations, trim equations, and wind angle of attack equations. Analog wiring diagrams, raw data and time-varying coefficients, and state variable responses during shuttle ascent are also considered.

Connor, C. L.↗
NASA NTRS1972

Computerized optimal control system design for reusable and expendable boost vehicles.

An optimization technique has been developed which combines the practical features of hybrid simulation of the dynamic system under study with the systematic approach of modern control theory where a mathematically formulated design criterion is optimized by functional minimization. Standard hybrid computer optimization methods using high-speed repetitive simulations and gradient minimization schemes have been extended to obtain time-varying optimal gain schedules and reduce the sensitivity of the optimized system to parameter and disturbance uncertainties. In this approach the performance index is expressed in meaningful engineering terms that reflect the interactions among all major disciplines, structures, control/actuation system design, aerodynamics and performance. The basic optimization technique is developed and its application to current aerospace control problems including the space shuttle is presented in detail. In the discussion of the application, the controllers resulting from the technique are compared with controllers developed by conventional methods. The paper concludes with a review of the advantages and disadvantages of the technique and plans for future applications.

Connor, C. L.↗