Engineering Papers⌕ Search

Engineering topics

Tompkins, S. S.

Publications and source records attributed to Tompkins, S. S..

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

Sensitivity of the coefficients of thermal expansion of selected graphite reinforced composite laminates to lamina thermoelastic properties

An analytical study of the sensitivity of the laminate coefficient of thermal expansion, CTE, to changes in lamina elastic properties has been made. High modulus graphite/epoxy (P75/934, P100/934, P120/934), graphite/aluminum (P100/Al), and graphite/glass (HMS/Gl) composite materials were considered in quasi-isotropic, low thermal stress, and 'near-zero' thermal expansion laminate configurations. The effects of a positive or negative 10 percent change in lamina properties on laminate CTE is strongly dependent upon both the composite material and the laminate configuration. A 10 percent change in all of the lamina properties had very little effect on the laminate CTE of the HMS/Gl composite laminates investigated. The sensitivity and direction of change in the laminate CTE of Gr/934 depended very strongly on the fiber properties. A 10 percent change in the lamina transverse CTE resulted in changes as large as 0.216 ppm/C in the laminate CTE of a quasi-isotropic Gr/934 laminate. No significant difference was observed in the sensitivity of the laminate CTE of the P100/934 and P120/934 composite materials due to changes in lamina properties. Large changes in laminate CTE can result from measured temperature and radiation effects on lamina properties.

Tompkins, S. S.↗
NASA NTRS1988

Thermally induced twist in graphite-epoxy tubes

This paper discusses an analytical and experimental study to investigate the thermally induced twist in laminated angle-ply graphite-epoxy tubes. Attention is focused on balanced laminates which, contrary to intuition, exhibit twist when the temperature is changed. The twisting is due to the fact that a lamina with ( a + phi) orientation and a lamina with (a - phi) orientation must be at slightly different radial positions in the twist. The lamina with the greater radial position determines the sense of the twist. Classical lamination theory does not predict this phenomenon, and so as more sophisticated theory must be employed. This paper outlines such as theory, which is based on an generalized plane-deformation elasticity analysis, and presents experimental data to confirm the predictions of the theory. A brief description of the experimental apparatus and procedure used to measure twist is presented.

Hyer, M. W.↗
NASA NTRS1988

Response of composite materials to the Space Station orbit environment

The rationale for selecting composite materials with an anodized aluminum foil coating for the Space Station is presented. Data on the effects of the space service environment on these materials are given. Results are also presented on the effect of optical properties of an aluminum/aluminum oxide coating on the thermal balance of the cylindrical structural members. The resistance of this coating to solar ultraviolet degradation is discussed.

Tompkins, S. S.↗
NASA NTRS1987

Temperature and deflection data from the asymmetric heating of cross-ply composite tubes

Data generated while heating several cross-ply graphite-epoxy tubes on one side, along their lengths, and cooling them on the other side are presented. This heating arrangement produces a circumferential temperature gradient, and the data show that the gradient can be represented by a cosinusoidal temperature distribution. The thermally induced bending deflections caused by the temperature gradient are also presented.

Hyer, Michael W.↗
NASA NTRS1987

Thermal expansion of selected graphite-reinforced polyimide-, epoxy-, and glass-matrix composites

The thermal expansion of continuous carbon-fiber reinforced composites with epoxy-, polyimide-, and borosilicate glass-matrices has been measured and compared. The expansion of a rubber-toughened epoxy-matrix/P75S carbon-fiber composite was very different from the expansion of two different single-phase epoxy-matrix/P75S composites, although all three had the same stacking sequence. Reasonable agreement was obtained between measured thermal expansion data and results from classical laminate theory. Microdamage in the graphite/polyimide laminate, induced by 250 cycles between -156 and 121 C, caused a 53 percent decrease in the coefficient of thermal expansion. The thermal expansion of the graphite/glass laminate was not changed after 100 thermal cycles from -129 to 38 C; however, a residual strain of about 10 x 10 to the -6 was observed for the laminate tested.

Tompkins, S. S.↗
NASA NTRS1986

Effects of thermal cycling on graphie-fiber-reinforced 6061 aluminum

Graphite-reinforced aluminum alloy metal-matrix composites are among materials being considered for structural components in dimensionally stable space structures. This application requires materials with low values of thermal expansions and high specific stiffnesses. They must remain stable during exposures to the space environment for periods extending to 20 years. The effects of thermal cycling on the thermal expansion behavior and mechanical properties of Thornel P100 graphite 6061 aluminum composites, as fabricated and after thermal processing to eliminate thermal strain hysteresis, have been investigated. Two groups of composites were studied: one was fabricated by hot roll bonding and the other by diffusion bonding. Processing significantly reduced strain hysteresis during thermal cycling in both groups and improved the ultimate tensile strength and modulus in the diffusion-bonded composites. Thermal cycling stabilized the as-fabricated composites by reducing the residual fabrication stress and increased the matrix strength by metallurgical aging. Thermal expansion behavior of both groups after processing was insensitive to thermal cycling. Data scatter was too large to determine effects of thermal cycling on the mechanical properties. The primary effects of processing and thermal cycling can be attributed to changes in the metallurgical condition and stress state of the matrix.

Dries, G. A.↗
NASA NTRS1986

Thermally induced stresses in cross-ply composite tubes

An approximate solution for determining stresses in cross-ply composite tubes subjected to a circumferential temperature gradient is presented. The solution is based on the principle of complementary virtual work (PCVW) in conjunction with a Ritz approximation on the stress field and accounts for the temperature dependence of material properties. The PCVW method is compared with a planar elasticity solution using temperature-independent material properties and a Navier approach. The net effect of including temperature-dependent material properties is that the peak absolute values of the stresses are reduced. The dependence of the stresses on the circumferential location is also reduced in comparison with the case of temperature-independent properties.

Hyer, M. W.↗
NASA NTRS1985

The thermal and mechanical stability of composite materials for space structures

A continuing research objective of the National Aeronautical and Space Administration (NASA) is to develop advanced composite materials for space structures. The thrust of this research is to gain fundamental understanding of the performance of advanced composites in the space environment. The emphasis has been to identify and model changes in the thermal-physical properties due to induced damage and develop improved materials.

Tompkins, S. S.↗
NASA NTRS1985

Thermal expansion of selected graphite reinforced polyimide-, epoxy-, and glass-matrix composite

The thermal expansion of three epoxy-matrix composites, a polyimide-matrix composite and a borosilicate glass-matrix composite, each reinforced with continuous carbon fibers, has been measured and compared. The expansion of a composite with a rubber toughened epoxy-matrix and P75S carbon fibers was very different from the expansion of two different single phase epoxy-matrix composites with P75S fibers although all three had the same stacking sequence. Reasonable agreement was obtained between measured thermal-expansion data and results from classical laminate theory. The thermal expansion of a material may change markedly as a result of thermal cycling. Microdamage, induced by 250 cycles between -156 C and 121 C in the graphite/polyimide laminate, caused a 53 percent decrease in the coefficient of thermal expansion. The thermal expansion of the graphite/glass laminate was not changed by 100 thermal cycles from -129 C to 38 C; however, a residual strain of about 10 x 10 to the minus 6 power was measured for the laminate tested.

Tompkins, S. S.↗
NASA NTRS1985

NASA space materials research

The effect of the space environment on: (1) thermal control coatings and thin polymer films; (2) radiation stability of 250 F and 350 F cured graphite/epoxy composites; and (3) the thermal mechanical stability of graphite/epoxy, graphite/glass composites are considered. Degradation in mechanical properties due to combined radiation and thermal cycling is highlighted. Damage mechanisms are presented and chemistry modifications to improve stability are suggested. The dimensional instabilities in graphite/epoxy composites associated with microcracking during thermal cycling is examined as well as the thermal strain hysteresis found in metal-matrix composites.

Tenney, D. R.↗
NASA NTRS1985

Thermally induced stresses and deformations in layered composite tubes

The thermally induced stresses and deformations in layered, orthotropic tubes are studied. The motivation for studying tubes is their likely application for use in space structures. Tubes are a strong candidate for this application because of their high structural efficiency, as measured by stiffness per unit weight, and their relative ease of fabrication. Also, tubes have no free edges to deteriorate or delaminate. An anticipated thermal condition for tubes in space is a circumferential temperature gradient. This type of gradient will introduce dimensional changes into the structure and may cause stresses large enough to cause damage to the material. There are potentially large differences in temperatures at different circumferential locations on the tube. Because of this, the effects of temperature dependent material properties on the stresses and deformations may be important. The study is composed of three parts: experiments to determine the functional form of the circumferential gradient and to measure tube deflections; an elasticity solution to compute the stresses and deformations; and an approximate approach to determine the effects of temperature dependent material properties.

Cooper, D. E.↗
NASA NTRS1984

Electron radiation effects on the thermal expansion of graphite/resin composites

The effects of 1 MeV electron radiation on the thermal expansion characteristics of two graphite reinforced resin matrix composite systems were studied. Specimens of both graphite/epoxy (T300/5208) and graphite/polyimide (C6000/PMR15) were irradiated to a total dose of 6 x 10 to the 9th rads at two different rates. Dynamic mechanical analyses (DMA) were performed to study changes in resin chemistry. Thermal expansion results indicate that radiation did produce permanent residual strains of up to -70 x 10 to the -6th for the graphite/epoxy when exposed to temperatures up to +280 F. However, no permaanent changes in the coefficient of thermal expansion (CTE) were observed. No permanent residual strains or changes in the CTE attributable to radiation were observed for the graphite/polyimide specimens. DMA results indicate that electron radiation caused chemical changes in the epoxy matrix. These changes resulted in a lower glass transition temperature and broader 'rubbery region' which extended into the temperature range of the thermal expansion tests.

Bowles, D. E.↗
NASA NTRS1984

The effects of thermal cycling on matrix cracking and stiffness changes in composite tubes

The study investigated the accumulation of transverse matrix cracks and the resultant loss of torsional, extensional, and bending stiffnesses in 8 layer 0.5 in. diameter crossply tubes subjected to thermal cycling. The tubes were graphite-epoxy and the temperature range during cycling was -250 to 200 F. The effect of fiber and matrix properties was investigated through the use of T300 and P75S fibers and 934 and CE339 resins. The study considered 0, 10, 50, 100, 300, and 500 thermal cycles. Photomicrographs, X-rays, and edge replication were used to evaluate cracking. Special loading fixtures were used to measure stiffness changes. An important finding was that for the tubes studied, even with extensive cracking, the bending and extensional stiffnesses were not affected. The torsional stiffness, however, was strongly affected.

Cohen, D.↗
NASA NTRS1984

A laser interferometer dilatometer for thermal expansion measurements of composites

A high precision Fizeau type, laser interferometer dilatometer system has been developed for low expansion composite materials. The strain resolution is about 1 microstrain. The system is automated to operate over a large temperature range and record data during the test in real time. A technique has been developed to reduce the fringe data in real time to length changes. The dilatometer system is described and thermal expansion measurements for several fiber-reinforced and particle filled composites are presented.

Tompkins, S. S.↗
NASA NTRS1982

Development of a Priest interferometer for measurement of the thermal expansion of a graphite epoxy in the temperature range 116-366 K

The thermal expansion behavior of graphite epoxy laminates between 116 and 366 degrees Kelvin was investigated using as implementation of the Priest interferometer concept. The design, construction and use of the interferometer along with the experimental results it was used to generate are described. The experimental program consisted of 25 tests on 25.4 mm and 6.35 mm wide, 8 ply pi/4 quasi-isotropic T300-5208 graphite/epoxy specimens and 3 tests on a 25.4 mm wide unidirectional specimen. Experimental results are presented for all tests along with a discussion of the interferometer's limitations and some possible improvements in its design.

Short, J. S.↗
NASA NTRS1982

Thermal expansion of graphite-epoxy between 116 K and 366 K

A Priest laser interferometer was developed to measure the thermal strain of composite laminates. The salient features of this interferometer are that: (1) it operates between 116 K and 366 K; (2) it is easy to operate; (3) minimum specimen preparation is required; (4) coefficients of thermal expansion in the range of 0-5 micro epsilon/K can be measured; and (5) the resolution of thermal strain is on the order of micro epsilon. The thermal response of quasi-isotropic, T300/5208, grahite-epoxy composite material was studied with this interferometer. The study showed that: (1) for the material tested, thermal cycling effects are negligible; (2) variability of thermal response from specimen to specimen may become significant at cryogenic temperatures; and (3) the thermal response of 0.6 cm and 2.5 cm wide specimens are the same above room temperature.

Short, J. S.↗
NASA NTRS1982

Effects of thermal cycling on residual mechanical properties of C6000/PMR-15 graphite polyimide

An experimental study to determine the effects of thermal cycling on residual mechanical properties of a graphite/polyimide composite has been conducted. Interlaminar shear, flexure and compression strengths were measured at room temperature and 316 C on unidirectional and quasi-isotropic laminates subjected to 150 and 500 thermal cycles between -156 C and 316 C. Thermal cycling produced transverse microcracks and delaminations in the laminates. The linear density of the microcracks (35/cm) was about the same after 150 and 500 cycles. Although the crack density did not change from 150 to 500 cycles, crack growth did occur with intralamina cracks growing into adjacent lamina. The matrix controlled properties of the quasi-isotropic laminate at both room temperature and 316 C were significantly reduced by thermal cycling. However, the properties of the unidirectional laminate were significantly reduced only at 316 C.

Tompkins, S. S.↗