Engineering Papers⌕ Search

Engineering topics

Tiwari, S. N.

Publications and source records attributed to Tiwari, S. N..

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

Effects of nose bluntness and angle of attack on slender bodies in hypersonic flows

The effects of angle of attack and nose bluntness on the flow field and wall quantities are investigated for hypersonic flows of air over slender bodies. The bodies considered are slender cones and straight biconic configurations. The numerical procedures used are based on the solution of complete Navier-Stokes equations in the nose region and parabolized Navier-Stokes equations in the downstream region. Results are obtained for a wide range of free stream conditions in which the gas behind the shock is treated as perfect. The flow field variables and surface quantities show significant differences when the angle of attack and nose bluntness are varied. The postshock flow field is studied in detail from the contour plots of Mach number, density, and temperature. Flow separation is observed on the leeward plane for an on-axis, 12.84 deg/7 deg (fore-cone and aft-cone angles) biconic geometry at 12 deg angle of attack. Also, the windward and leeward heating rates for the fore-cone section decrease by a factor of four and five, respectively, when the nose bluntness is increased by an order of magnitude. The effect of nose bluntness for slender cone persists as far as 200 nose radii downstream.

Tiwari, S. N.↗
NASA NTRS1992

Combined effect of nose bluntness and angle of attack on slender bodies in viscous hypersonic flows

Hypersonic flows over cones and straight biconic configurations are calculated for a wide range of free stream conditions in which the gas behind the shock is treated as perfect. Effect of angle of attack and nose bluntness on these slender cones in air is studied extensively. The numerical procedures are based on the solution of complete Navier-Stokes equations at the nose section and parabolized Navier-Stokes equations further downstream. The flow field variables and surface quantities show significant differences when the angle of attack and nose bluntness are varied. The complete flow field is thoroughly analyzed with respect to velocity, temperature, pressure, and entropy profiles. The post shock flow field is studied in detail from the contour plots of Mach number, density, pressure, and temperature. The effect of nose bluntness for slender cones persists as far as 200 nose radii downstream.

Tiwari, S. N.↗
NASA NTRS1991

Toughening of PMR composites by semi-interpenetrating networks

Polymerization of monomer reactants (PMR-15) type polyimide and RP46 prepregs were drum wound using IM-7 fibers. Prepregging and processing conditions were optimized to yield good quality laminates with fiber volume fractions of 60 percent (+/- 2 percent). Samples were fabricated and tested to determine comprehensive engineering properties of both systems. These included 0 deg flexure, short beam shear, transverse flexure and tension, 0 deg tension and compression, intralaminar shear, short block compression, mode 1 and 2 fracture toughness, and compression after impact properties. Semi-2-IPN (interpenetrating polymer networks) toughened PMR-15 and RP46 laminates were also fabricated and tested for the same properties.

Tiwari, S. N.↗
NASA NTRS1991

Morphology and microstructure of composite materials

Lightweight continuous carbon fiber based polymeric composites are currently enjoying increasing acceptance as structural materials capable of replacing metals and alloys in load bearing applications. As with most new materials, these composites are undergoing trials with several competing processing techniques aimed at cost effectively producing void free consolidations with good mechanical properties. As metallic materials have been in use for several centuries, a considerable database exists on their morphology - microstructure; and the interrelationships between structure and properties have been well documented. Numerous studies on composites have established the crucial relationship between microstructure - morphology and properties. The various microstructural and morphological features of composite materials, particularly those accompanying different processing routes, are documented.

Tiwari, S. N.↗
NASA NTRS1991

Application of a Reynolds Stress turbulence model to a supersonic hydrogen-air diffusion flame

A second-order differential Reynolds Stress turbulence model has been applied to the Favre-averaged Navier-Stokes equations for the study of supersonic flows undergoing hydrogen-air chemical reactions. An assumed Beta Probability Density Function is applied to account for the chemical source terms in the conservation equations. An algebraic Reynolds Flux model is used for the fluctuating density-velocity as well as the species mass fraction-velocity correlations. The variances of temperature and species fluctuations are also modelled using an algebraic flux technique. A seven-species, seven-reaction finite rate chemistry mechanism is used to simulate the combustion processes. The resulting formulation is validated by comparison with experimental data on reacting supersonic axisymmetric jets. Results obtained for specific conditions indicate that the effect of chemical reaction on the turbulence is significant.

Chandrasekhar, R.↗
NASA NTRS1991

Investigation of nose bluntness and angle of attack effects on slender bodies in viscous hypersonic flows

Hypersonic flows over cones and straight biconic configurations are calculated for a wide range of free stream conditions in which the gas behind the shock is treated as perfect. Effect of angle of attack and nose bluntness on these slender cones in air is studied extensively. The numerical procedures are based on the solution of complete Navier-Stokes equations at the nose section and parabolized Navier-Stokes equations further downstream. The flow field variables and surface quantities show significant differences when the angle of attack and nose bluntness are varied. The complete flow field is thoroughly analyzed with respect to velocity, temperature, pressure, and entropy profiles. The post shock flow field is studied in detail from the contour plots of Mach number, density, pressure, and temperature. The effect of nose bluntness for slender cones persists as far as 200 nose radii downstream.

Sehgal, A. K.↗
NASA NTRS1991

Radiative interactions in chemically reacting supersonic internal flows

The two-dimensional, elliptic Navier-Stokes equations are used to investigate supersonic flows with finite-rate chemistry and radiation for hydrogen-air systems. The chemistry source terms in the species equation is treated implicitly to alleviate the stiffness associated with fast reactions. The explicit, unsplit MacCormack finite-difference scheme is used to advance the governing equations in time, until convergence is achieved. The specific problem considered is the premixed flow in a channel with a ten-degree compression ramp. Three different chemistry models are used, accounting for increasing number of reactions and participating species. Two chemistry models assure nitrogen as inert, while the third model accounts for nitrogen reactions and NO(x) formation. The tangent slab approximation is used in the radiative flux formulation. A pseudo-gray model is used to represent the absorption-emission characteristics of the participating species. Results obtained for specific conditions indicate that the radiative interactions vary substantially, depending on reactions involving HO2 and NO species and that this can have a significant influence on the flowfield.

Tiwari, S. N.↗
NASA NTRS1991

Impact response of composite materials

Composite materials composed of carbon fibers and resin matrices offer great promise in reducing the weight of aerospace structures. However they remain extremely vulnerable to out of plane impact loads, which lead to severe losses in strength and stiffness. The results of an experimental program, undertaken to investigate the low velocity impact damage tolerance of composite materials is presented. The objectives were to identify key neat resin/composite properties that lead to enhancement of composite impact damage tolerance and to find a small scale test that predicts compression after impact properties of panels. Five materials were selected for evaluation. These systems represented different classes of material behavior such as brittle epoxy, modified epoxies, and amorphous and semicrystalling thermoplastics. The influence of fiber properties on the impact performance was also studied in one material, i.e., in polyether ether ketone (PEEK). Several 24 and 48 ply quasi-isotropic and 24 ply orthotropic laminates were examined using an instrumented drop weight impactor. Correlations with post impact compression behavior were made.

Tiwari, S. N.↗
NASA NTRS1991

Two and three-dimensional shock-shock interactions on the blunt leading edges of the hypersonic inlets

The effect of shock impingement on the blunt leading edges of the top and sidewall compression type inlet of a scramjet engine is studied numerically. The impinging shock is caused by the vehicle forebody. The interaction of this forebody shock with the inlet leading edge shock results in a very complex flowfield containing local regions of high pressure and intense heating. This complex flowfield in calculated by solving the Navier-Stokes equations using a finite volume flux splitting technique due to van Leer. To resolve the finer details of the flow structure as well as to predict the surface heat transfer accurately, adaptive grid technique is used in the analysis. Results of the present numerical study are compared with available experimental results.

Singh, D. J.↗
NASA NTRS1991

Radiative interactions in a hydrogen-fueled supersonic combustor

The two-dimensional, elliptic Navier-Stokes equations are used to investigate supersonic flows with finite-rate chemistry and radiation, for hydrogen-air systems. The chemistry source term in the species equation is treated implicitly to alleviate the stiffness associated with fast reactions. The explicit, unsplit MacCormack finite-difference scheme is used to advance the governing equations in time, until convergence is achieved. The specific problem considered is the premixed flow in a channel with a 10-deg compression ramp. Three different chemistry models are used, accounting for increasing number of reactions and participating species. Two chemistry models assume nitrogen as inert, while the third model accounts for nitrogen reactions and NO(x) formation. The tangent slab approximation is used in the radiative flux formulation. A pseudogray model is used to represent the absorption-emission characteristics of the participating species. Results otained for specific conditions indicate that the radiative interactions vary substantially, depending on reactions involving HO2 and NO species, and that this can have a significant influence on the flowfield.

Chandrasekhar, R.↗
NASA NTRS1991

Investigation of radiative interactions in chemically reacting supersonic internal flows

Analyses and numerical procedures are presented to investigate the radiative interactions of absorbing-emitting species in chemically reacting supersonic flow in various ducts. Specific attention is directed in investigating the radiative contributions of H2O, OH, and NO under realistic physical and flow conditions. The radiative interactions in reacting flows are investigated by considering the supersonic flow of premixed hydrogen and air in a channel with a compression corner at the lower boundary. The results indicate that radiation can have significant influence on the flowfield and species production depending on the chemistry model employed.

Tiwari, S. N.↗
NASA NTRS1990

Radiative interactions in laminar duct flows

Analyses and numerical procedures are presented for infrared radiative energy transfer in gases when other modes of energy transfer occur simultaneously. Two types of geometries are considered, a parallel plate duct and a circular duct. Fully developed laminar incompressible flows of absorbing-emitting species in black surfaced ducts are considered under the conditions of uniform wall heat flux. The participating species considered are OH, CO, CO2, and H2O. Nongray as well as gray formulations are developed for both geometries. Appropriate limiting solutions of the governing equations are obtained and conduction-radiation interaction parameters are evaluated. Tien and Lowder's wide band model correlation was used in nongray formulation. Numerical procedures are presented to solve the integro-differential equations for both geometries. The range of physical variables considered are 300 to 2000 K for temperature, 0.1 to 100.0 atm for pressure, and 0.1 to 100 cm spacings between plates/radius of the tube. An extensive parametric study based on nongray formulation is presented. Results obtained for different flow conditions indicate that the radiative interactions can be quite significant in fully developed incompressible flows.

Trivedi, P. A.↗
NASA NTRS1990

Interactive real time flow simulations

An interactive real time flow simulation technique is developed for an unsteady channel flow. A finite-volume algorithm in conjunction with a Runge-Kutta time stepping scheme was developed for two-dimensional Euler equations. A global time step was used to accelerate convergence of steady-state calculations. A raster image generation routine was developed for high speed image transmission which allows the user to have direct interaction with the solution development. In addition to theory and results, the hardware and software requirements are discussed.

Sadrehaghighi, I.↗
NASA NTRS1990

Grid generation and flow computation about a Martian entry vehicle

A number of vehicles are currently being proposed for a manned mission to Mars. One of these vehicles has a modified blunt-nosed cone configuration. Experimental results were obtained for this vehicle in 1968. They show lift-over-drag ratios comparable to those needed for Mars entry. Computations are performed to verify the earlier results and to further describe the flight characteristics of this vehicle. An analytical method is used to define the surface of this vehicle. A single-block volume grid is generated around the vehicle using the algebraic Two-Boundary Grid Generation algorithm (TBGG) and transfinite interpolation. Euler solutions are then obtained from a Langley Aerodynamic Upward Relaxation Algorithm (LAURA) at Mach 6.0 and angles of attack of 0, 6, and 12 deg. The lift coefficient determined from the LAURA code agree very well with the experimental results. The drag and pitching moment coefficients, however, are underestimated by the code since viscous effects are not considered. Contour plots of the flowfield show no evidence of separation for angles of attack up to 12 deg.

Stewart, J. E.↗
NASA NTRS1990

Development of polysilsesquioxane composites

Polymer composites are increasingly being required to operate for prolonged durations at higher temperatures than in the past. Hence there have been increased efforts devoted to synthesizing and characterizing polymers capable of withstanding temperatures greater than 300 C for long periods. Several such organic polymers have been investigated in recent times. This research effort seeks to enquire if inorganic polymers can be utilized to provide the same result. Ceramics have long been recognized as providing superior thermal properties for demanding applications. However, the extremely high softening temperatures preclude their being shaped into complex shapes through melt processing techniques common to organic polymers. One approach towards solving this problem has been through the development of preceramic polymers. These are capable of being processed in the polymeric state with ease, and subsequently being pyrolyzed to ceramic structures. This experimental study is aimed at studying the feasibility of using preceramic polymers (that have not been subject to the pyrolysis step) as high performance composite matrices for high temperature applications. A preliminary study of this nature is not geared towards optimizing mechanical properties suitable for such composites. Rather, this study attempts to process such resins in composite form and suitably characterize their properties.

Srinivasan, K.↗
NASA NTRS1990

Numerical Formulation for the Prediction of Solid/Liquid Change of a Binary Alloy

A computational model is presented for the prediction of solid/liquid phase change energy transport including the influence of free convection fluid flow in the liquid phase region. The computational model considers the velocity components of all non-liquid phase change material control volumes to be zero but fully solves the coupled mass-momentum problem within the liquid region. The thermal energy model includes the entire domain and uses an enthalpy like model and a recently developed method for handling the phase change interface nonlinearity. Convergence studies are performed and comparisons made with experimental data for two different problem specifications. The convergence studies indicate that grid independence was achieved and the comparison with experimental data indicates excellent quantitative prediction of the melt fraction evolution. Qualitative data is also provided in the form of velocity vector diagrams and isotherm plots for selected times in the evolution of both problems. The computational costs incurred are quite low by comparison with previous efforts on solving these problems.

Schneider, G. E.↗