Engineering topics

Thonhauser, Timo

Publications and source records attributed to Thonhauser, Timo.

15 records

DOE OSTI2024

Enhancing carbon dioxide capture under humid conditions by optimizing the pore surface structure

Metal–organic frameworks (MOFs) exhibit significant potential for mitigating carbon emissions due to their high porosity and tunability. Despite numerous reports on CO 2 capture by MOF sorbents, a common challenge is their poor selectivity for CO 2 over water. Moreover, in-depth studies are much needed to elucidate the relationships among the pore surface structure, hydrophobicity, and CO 2 uptake capacity/selectivity. In this work, we investigate the factors influencing CO 2 adsorption capacity and selectivity under humidity in a series of isoreticular pillar-layer structures, Ni 2 (L) 2 (dabco) (L = bdc, ndc, adc). Our study shows that increasing ligand conjugation not only results in increased hydrophobicity, decreased pore size and BET surface area, but also leads to the change of primary binding sites of water molecules and higher binding energy of CO 2 , all of which contribute to largely increased CO 2 uptake capacity under humid conditions. Additionally, increasing ligand conjugation and consequently hydrophobicity slow down and reduce competitive water adsorption drastically. Notably, the MOF made of ligand with the highest conjugation, Ni 2 (adc) 2 (dabco), exhibits significantly enhanced CO 2 adsorption in N 2 /CO 2 binary mixtures under relatively high humidity (50% RH), with an increase of ~31% and ~36% for the composition of 15/85 and 50/50, respectively, compared to dry conditions. An experimental FTIR study and DFT theoretical calculations confirm that H 2 O occupies different primary binding site in Ni 2 (bdc) 2 (dabco) and Ni 2 (adc) 2 (dabco), and under humid conditions a higher binding energy of CO 2 is achieved with preferential H 2 O/CO 2 co-adsorption in Ni 2 (adc) 2 (dabco), potentially creating additional adsorption sites for CO 2 .

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2024

Flexible MOFs as Pressure-Tunable Filters for Hydrocarbon Separation

Metal–organic frameworks (MOFs) hold significant promise for separating gas mixtures, especially hydrocarbons. While the main focus in the field is the development of new adsorbents for specific separations of binary mixtures, a preferable situation would be using a single framework for separating various species. This has been achieved in some flexible MOFs, where ternary mixtures can be separated at different temperatures. Here, we propose a simple yet fascinating way of utilizing the flexibility of MOFs to create tunable filters as a function of external pressure. We thus replace the more costly temperature-driven tunability with a cost-efficient external-pressure tunability. As a proof-of-concept, we select the CaMOF flexible framework for C6 hydrocarbon separation, however, our results are applicable to other flexible framework and gas molecules. Furthermore, our findings provide mechanistic insight and guidelines to engineer separation filters by designing flexible pores with critical sizes that can be effectively manipulated by external pressure.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Understanding and Tailoring Diffusion and Co-Adsorption Inside the Confined Pores of Metal-Organic Frameworks (Final Scientific/Technical Report for Award DE-SC0019902)

The aim of this program was to gain a fundamental understanding of the behavior of various guest molecules in nano-confined environments, such as metal organic frameworks (MOFs), using a combination of novel synthesis, ab initio modeling, and in situ characterization. Through this project, we developed a concise understanding of the mechanisms that control adsorption/desorption of gaseous molecules and their mixtures, leading to design/synthesis guidelines for MOFs with desired functionality. We further developed methods to disentangle kinetic from thermodynamic effects during adsorption, as well as to characterize the interactions at play. In the first funding cycle, the focus was on the unambiguously characterization of co-adsorption and diffusion of gasses/vapors and their mixtures. In the second funding cycle, the focus was on characterizing the effects of the nano-confinement on the kinetics and thermodynamics of adsorption processes inside MOFs, again with an emphasis on mixtures of gasses and vapors. The nano-confinement can tip the thermodynamic vs. kinetic balance, and current understanding and theory based on single-component analysis can lead to incorrect predictions for mixtures. This is of particular interest in real-world applications, where gasses/vapors are typically mixed, contain impurities, or are often exposed to humid conditions. Our main findings were: (i) within confined environments the adsorption behavior of mixed gasses/vapors can be drastically different from the “sum” of the corresponding single phases; (ii) co-adsorption is often competitive and detrimental to performance, but it can also be cooperative and beneficial; (iii) in some co-adsorbed gasses/vapors, molecules that are strongly bound in the single-component phase can be replaced by molecules that are nominally weaker bound (molecular exchange) due to guest-guest interactions that lower the kinetic barriers and favor the final adsorption state; (iv) kinetic and thermodynamic effects can be precisely controlled through pore-size engineering and synthesis; and, (v) kinetic effects can be identified and disentangled from thermodynamic effects during adsorption through a series of sequential and simultaneous gas loading measurements. The short-term goal of this program was the controlling and understanding of common MOF systems in real-world situations where gasses/vapors are mixed, which will have an important impact on industrial processes and applications from gas storage and sequestration to catalysis and sensors. The long-term goals include the development of theoretical and experimental methods for gaining a fundamental understanding of adsorption/reaction processes within MOFs, as well as new guidelines for synthesizing MOFs with tailored physical and chemical properties.

36 MATERIALS SCIENCE↗

DOE OSTI2024

THD-C Sheet: A Novel Nonbenzenoid Carbon Allotrope with Tetra-, Hexa-, and Dodeca-Membered Rings

Here, we propose a novel two-dimensional carbon-based structure with tetra-, hexa-, and dodeca-membered rings, which we refer to by the abbreviated name, THD-C. The structure presents a mixture of sp–sp 2 hybridization and can potentially be synthesized by the topological assembly of 4-ethynyldiphenylacetylene molecules. By employing first-principles calculations, the stability and ease of synthesis of the sheet are investigated and compared with various C-allotropes. We predict its metallic behavior and excellent kinetic and dynamic stability. Due to the crystal structure of the sheet, a strong mechanical anisotropy is observed. The effects of functionalization on the electronic properties of the material are also studied, and different semiconducting systems are obtained. The potential of THD-C for energy storage in metal-based batteries, hydrogen storage, and catalysis is also investigated, and we find a superior performance in comparison to graphite and other allotropes. The quantum confinement effect is investigated by constructing nanoribbons and nanotubes of various sizes. For ribbons, we find that tailor-made electronic and magnetic properties can be obtained and explored in potential spintronic devices. Additionally, we observe that nanotubes are conducting irrespective of their chirality and can potentially be used for capture, storage, and separation of industrially relevant small gas molecules.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Real-time observation of the exchange process between H 2 O and NO in the metal–organic framework Ni-MOF-74

Molecular exchange is a common step occurring in many technological processes such as competitive adsorption, chemical separation, capture, delivery, and release. However, the underlying principle is not fully understood, especially in nanoconfined environments where the energetics and kinetics of such processes can deviate from that on flat surfaces. In this study, we unravel the mechanism of a molecular exchange process by studying the displacement of NO by H 2 O in Ni-MOF-74 in real-time using in situ infrared spectroscopy combined with ab initio calculations. We show that weakly bound H 2 O gradually displaces strongly bound NO on the metal sites by first weakening the M–N bond through forming H-bond and then moving the NO away so that it eventually desorbs. Interestingly, we further find that additional water facilitates this exchange by significantly lowering the kinetic barrier associated with this process as well as the overall energy of the final state. Although our study focuses on Ni-MOF-74, we believe that our finding and explanation of unexpected exchange phenomena—where strongly adsorbed molecules are apparently easily displaced by much weaker bound H 2 O—is applicable to a much larger group of frameworks and will be helpful in designing and improving MOFs for real-world applications where humidity is often present.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2023

An Octacarboxylate-Linked Sodium Metal–Organic Framework with High Porosity

Alkali metal-based metal-organic frameworks (MOFs) with permanent porosity are scarce because of their high tendency to coordinate with solvents such as water. However, these MOFs are lightweight and bear gravimetric benefits for gas adsorption related applications. In this paper, we present the successful construction of a microporous MOF, designated as HIAM-111, built solely on sodium ions using an octacarboxylate linker. The structure of HIAM-111 is based on 8-connected Na4 clusters and exhibits a novel topology with an underlying 3 2 ,4 2 ,8-c net. Remarkably, HAM-111 possesses a robust and highly porous framework, with a BET surface area of 1561 m 2 /g, significantly surpassing that of the previously reported Na-MOFs. Further investigations demonstrate that HIAM-111 is capable of separating C 2 H 2 /CO 2 and purifying C 2 H 4 directly from C 2 H 4 /C 2 H 2 /C 2 H 6 with high adsorption capacities. The current work may shed light on the rational design of robust and porous MOFs based on alkali metals.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2023

Nickel Isonicotinate Framework with Optimal Pore Structure for Complete Discrimination of Hexane Isomers

Efficient separation of physicochemically similar alkanes is of vital importance. Adsorptive separation utilizing porous materials such as metal–organic frameworks with tunable pore structure and surface functionality represents an energy-efficient technology. In this study, we demonstrate successful separation of alkanes with varying degree of branching using a microporous nickel isonicotinate framework, Ni(4-PyC) 2 . Its 2-fold interpenetrated diamondoid structure with well-suited pore size enables selective adsorption of linear and monobranched hexane isomers, while excluding dibranched isomer. Breakthrough experiments validated its capability to completely discriminate all three hexane isomers. Ab initio calculations combined with in situ infrared spectroscopic analysis unveiled the nature of host–guest interactions and differences in the binding energies and diffusion barriers among the isomers. Furthermore, having well-balanced adsorption uptakes (146 and 79 mg g –1 of nHEX and 3MP), high nHEX/DMB uptake ratio (12.2) and fast kinetics, Ni(4-PyC) 2 stands out as a promising adsorbent for complete separation of hexane isomers under ambient conditions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2023

Luminescent Metal–Organic Framework for the Selective Detection of Aldehydes

The detection of toxic, hazardous chemical species is an important task because they pose serious risks to either the environment or human health. Luminescent metal–organic frameworks (LMOFs) as alternative sensors offer rapid and sensitive detection of chemical species. Interactions between chemical species and LMOFs result in changes in the photoluminescence (PL) profile of the LMOFs which can be readily detected using a simple fluorometer. Herein, we report the use of a robust, Zn-based LMOF, [Zn 5 (μ 3 -OH) 2 (adtb) 2 (H 2 O) 5 ·5 DMA] (Zn-adtb, LMOF-341), for the selective detection of benzaldehyde. Upon exposure to benzaldehyde, Zn-adtb experiences significant luminescent quenching, as characterized through PL experiments. Photoluminescent titration experiments reveal that LMOF-341 has a detection limit of 64 ppm and a Ksv value of 179 M –1 for benzaldehyde. Furthermore, we study the guest–host interactions that occur between LMOF-341 and benzaldehyde through in situ Fourier transform infrared and computational modeling employing density functional theory. The results show that benzaldehyde interacts more strongly with LMOF-341 compared to formaldehyde and propionaldehyde. Furthermore, our combined studies also reveal that the mechanism of luminescence quenching originates from an electron-transfer process.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2023

Simultaneous removal of C 2 H 2 and C 2 H 6 for C 2 H 4 purification by robust MOFs featuring a high density of heteroatoms

Simultaneous removal of C 2 H 6 and C 2 H 2 from C 2 H 4 streams is of great importance in the petrochemical industry but remains a challenging task. To address this challenge, we have selected three isoreticular MOFs with high stability, low cost, and desirable scale-up ability, namely, MOF-303, MIL-160, and CAU-23 and assessed their potential in simultaneous removal of acetylene and ethane for ethylene purification. Each MOF exhibits desirable C 2 H 2 and C 2 H 6 uptake capacity (>5.5 mmol g –1 and >4 mmol g –1 , respectively), as well as good C 2 H 2 /C 2 H 4 selectivity (>2) and C 2 H 6 /C 2 H 4 selectivity (>1.5). Notably, MOF-303 takes up 4.96 mmol g –1 C 2 H 6 at 298 K and 1 bar, the highest value among the three MOFs, with C 2 H 6 /C 2 H 4 selectivity in the range of 1.55–2.47. MIL-160 possesses a very high C 2 H 2 uptake (9.1 mmol g –1 ) and C 2 H 2 /C 2 H 4 selectivity, 10.6 (1 : 1, v/v), at 298 K, much higher than those of all other MOFs tested to date for simultaneous removal of C 2 H 6 and C 2 H 2 from C 2 H 4 . The results from breakthrough experiments confirm that all three MOFs demonstrate excellent performance for C 2 H 4 purification in a ternary mixture of C 2 H 6 /C 2 H 4 /C 2 H 2 (1 : 1 : 1, v/v/v). Here, for MOF-303, MIL-160, and CAU-23, polymer-grade C 2 H 4 up to 0.164, 0.21, and 0.181 mmol g –1 can be obtained from the equimolar ternary mixture in a single separation step from the breakthrough experiment. Additionally, DFT calculations have been performed to further investigate the mechanism of adsorption/separation for C 2 H 6 , C 2 H 4 , and C 2 H 2 .

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2023

Separating Xylene Isomers with a Calcium Metal‐Organic Framework

Abstract The purification of p‐xylene (pX) from its xylene isomers represents a challenging but important industrial process. Herein, we report the efficient separation of pX from its ortho‐ and meta‐ isomers by a microporous calcium‐based metal–organic framework material (HIAM‐203) with a flexible skeleton. At 30 °C, all three isomers are accommodated but the adsorption kinetics of o‐xylene (oX) and m‐xylene (mX) are substantially slower than that of pX, and at an elevated temperature of 120 °C, oX and mX are fully excluded while pX can be adsorbed. Multicomponent column breakthrough measurements and vapor‐phase/liquid‐phase adsorption experiments have demonstrated the capability of HIAM‐203 for efficient separation of xylene isomers. Ab initio calculations have provided useful information for understanding the adsorption mechanism.

Yu, Liang↗

DOE OSTI2023

Separating Xylene Isomers with a Calcium Metal–Organic Framework

Here, the purification of p-xylene (pX) from its xylene isomers represents a challenging but important industrial process. Herein, we report the efficient separation of pX from its ortho- and meta- isomers by a microporous calcium-based metal–organic framework material (HIAM-203) with a flexible skeleton. At 30 °C, all three isomers are accommodated but the adsorption kinetics of o-xylene (oX) and m-xylene (mX) are substantially slower than that of pX, and at an elevated temperature of 120 °C, oX and mX are fully excluded while pX can be adsorbed. Multicomponent column breakthrough measurements and vapor-phase/liquid-phase adsorption experiments have demonstrated the capability of HIAM-203 for efficient separation of xylene isomers. Ab initio calculations have provided useful information for understanding the adsorption mechanism.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2023

Magnetically Induced Binary Ferrocene with Oxidized Iron

Ferrocene is perhaps the most popular and well-studied organometallic molecule, but our understanding of its structure and electronic properties has not changed for more than 70 years. In particular, all previous attempts of chemically oxidizing pure ferrocene by binding directly to the iron center have been unsuccessful, and no significant change in structure or magnetism has been reported. Here, using a metal organic framework host material, we were able to fundamentally change the electronic and magnetic structure of ferrocene to take on a never-before observed physically stretched/bent high-spin Fe(II) state, which readily accepts O 2 from air, chemically oxidizing the iron from Fe(II) to Fe(III). We also show that the binding of oxygen is reversible through temperature swing experiments. Our analysis is based on combining Mößbauer spectroscopy, extended X-ray absorption fine structure, in situ infrared, SQUID, thermal gravimetric analysis, and energy dispersive X-ray fluorescence spectroscopy measurements with ab initio modeling.

36 MATERIALS SCIENCE↗

DOE OSTI2023

The effect of pore structure in ethane-selective metal-organic frameworks for ethylene purification

Separation of ethylene from ethane is of great importance in petrochemical industry. Adsorptive separation making use of porous materials such as metal-organic frameworks (MOFs) is an energy efficient technology compared to the conventional cryogenic distillation. However, preferential adsorption of ethylene over ethane represents the major current challenge. Here we demonstrate how pore structure can significantly alter the adsorption selectivity in two isoreticular Zr-MOFs. A simple ligand functionalization in UiO-66 yields smaller/better matching pore for ethane, and weaker interaction with ethylene, greatly enhancing ethane/ethylene selectivity in MOF-801. Ab initio calculations combined with in situ infrared spectroscopic analysis unveil the nature of host-guest interactions and differences in the overall binding energies. Polymer-grade ethylene (99.9%) can be produced directly from ethane/ethylene mixture in a single step. Having well-balanced adsorption capacity and selectivity, low-cost synthesis and easy scalability MOF-801 stands out as a promising ethane-selective adsorbent for one-step ethylene purification under ambient conditions.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Precise Pore Engineering of fcu–Type Y–MOFs for One–Step C 2 H 4 Purification from Ternary C 2 H 6 /C 2 H 4 /C 2 H 2 Mixtures

The purification of C 2 H 4 from C 2 H 6 /C 2 H 4 /C 2 H 2 mixtures is of great significance in the chemical industry for C 2 H 4 production but remains a daunting task. Guided by powerful reticular chemistry principles, herein a systematic study is carried out to engineer pore dimensions and pore functionality of fcu-type Y-based metal–organic frameworks (Y-MOFs) through the construction of a series of eight new structures using linear dicarboxylate linkers with different length and functional groups. This study illustrates how delicate changes in pore size and pore surface chemistry can effectively influence the adsorption preference of C 2 H 6 , C 2 H 4 , and C 2 H 2 by the MOFs. Importantly, clear relations between pore size/pore surface polarity and C 2 adsorption selectivities of this series of MOFs are established. In particular, HIAM-326 built on a linker decorated with trifluoromethoxy group shows notably preferential adsorption of C 2 H 6 and C 2 H 2 over C 2 H 4 , with balanced C 2 H 2 /C 2 H 4 and C 2 H 6 /C 2 H 4 selectivities. Furthermore, this endows the compound with the capability of one-step purification of C 2 H 4 from C 2 H 6 /C 2 H 4 /C 2 H 2 ternary mixtures, which is validated by breakthrough measurements where high purity C 2 H 4 (99.9%+) can be obtained directly from the separation column. Its adsorption thermodynamics and underlying selective adsorption mechanisms are further revealed by ab initio calculations.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Full Exclusion of Branched Hexanes from Their Linear Isomer by a Robust Aluminum Metal–Organic Framework with Tailored Pore Structure

High-efficiency separation of hexane isomers through selective molecular exclusion represents an important yet challenging task in the petrochemical industry. It has stringent requirements on the adsorbents' pore shape and dimensions. Here we report the complete exclusion of branched hexanes from their linear isomer by an aluminum metal-organic framework, CAU-21-ODB (ODB = 4,4'-oxydibenzoate) with high stability. The unique gourd-shaped channels with suitable pore aperture lead to substantial uptake of nHEX (141 mg/g at 30 °C) but negligible adsorption of its branched isomers under identical conditions. Furthermore, the capability of CAU-21-ODB for the separation of hexane isomers has been verified by multicomponent breakthrough experiments. DFT calculations further confirm the size-exclusion based separation mechanism.

36 MATERIALS SCIENCE↗