Life cycle assessment of charge carrier mediated electrocatalytic reduction of carbon dioxide to formic acid
Not Available
Matin, Naser S.↗
Engineering topics
Thompson, Jesse
Publications and source records attributed to Thompson, Jesse.
Decoupling Charge Carrier Electroreduction and Enzymatic CO 2 Conversion to Formate Using a Dual-Cell Flow Reactor System
Not Available
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Copper-Doped Tin Oxides Supported on Mesoporous Carbon Xerogel for Boosting the Electrochemical Reduction of CO 2 to Formate in Bicarbonate Solution Coupled with CO 2
The electrochemical reduction of CO 2 into valuable products at mild reaction conditions and using cheap renewable electrical energy are goals to sustain a low-carbon economy. Among the various CO 2 reduction reaction products, formic acid (FA) has received significant attention because of its low Gibbs free energy input requirement and the simple reduction reaction involving the transfer of 2 electrons and 2 protons. In this work, a copper-doped tin oxide catalyst supported on a mesoporous carbon xerogel was shown to enhance the electrochemical reduction of CO 2 to formate in a bicarbonate solution coupled with CO 2 . We observed that the synergistic SnCu oxides enhance the selectivity toward formate from 58.6% for Sn oxide and 28.7% for Cu oxide to over 71.2% for the SnCu oxides. The observed rate of formate production with SnCu oxide was 2.8 times higher compared to the rate of Cu oxide and about 1.5 times higher than with the Sn oxide catalyst. Our results reveal that selectivity for formate comes partly from the electrolysis of the bicarbonate solution and partly from continuous CO 2 gas purged into the solution. The contribution from the electrolysis of bicarbonate solution ranges from 15% to 40% when the concentration of bicarbonate solution ranges from 100 mM to 1 M. Chronoamperometric measurements for stability revealed that Cu oxide and Sn oxide showed stable current density for less than 30 h while under the same conditions, the stable current density was observed for more than 50 h with SnCu oxide catalyst. Additionally, the selectivity toward formate increased by 6% when the reactor pressure was increased from near ambient pressure to 4 psig. Our lab-scale electrochemical cell with SnCu oxide supported on the mesoporous carbon xerogel enhances the CO 2 solubility, minimizes the precipitation of salts that can degrade the catalytic performance, and suppresses the competitive hydrogen evolution reaction, demonstrating the feasibility of using our catalyst and system for the electrochemical conversion of CO 2 into formate with high selectivity, productivity, and stability. Furthermore, this could have significant implications for the mitigation of CO 2 emissions and the development of a sustainable chemical industry.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Downstream Separation of Formic Acid with Anion-Exchange Resin from Electrocatalytic Carbon Dioxide (CO 2 ) Conversion: Adsorption, Kinetics, and Equilibrium Modeling
The electrocatalytic carbon dioxide reduction reaction (CO 2 RR) that produces liquid formic acid (FA) is one potential route to minimize the CO 2 concentration in the atmosphere by utilizing CO 2 as a feedstock. However, one of the main disadvantages of this route is the high energy demand required for purification through conventional distillation. This method of purification has been shown to result in a large carbon footprint in life-cycle analysis (LCA). Therefore, finding an alternative purification technique that can integrate with an electrochemical CO 2 RR process with the potential to lower the carbon footprint would be of great interest. Under the experimental conditions of the CO 2 RR, FA remains in its basic form as the formate anion in the catholyte. Anion exchange resins with their basic properties can separate the formate anion from the catholyte mixture as an alternative to energy intensive distillation. In this work, three anion exchange resins with increasing basicity order: Amberlite IRA-96 < Amberlite IRA-910 < Ambersep 900 are tested to separate FA in the presence of aqueous solution of potassium bicarbonate catholyte with varying levels of resin and FA. Kinetics and equilibrium studies data for the FA adsorption are interpreted using several kinetics and isotherm models. The kinetics data fit well with a pseudo-first-order model at high initial FA concentrations and a pseudo-second-order model at low initial FA concentrations. The experimental data can be best explained with the Freundlich isotherm model. The fitted results show that strongly basic Ambersep 900 is more effective at separating FA, with a maximum adsorption capacity of 336.7 mg/g compared to Amberlite IRA-96 (275.2 mg/g) and Amberlite IRA-910 (209.2 mg/g) in neutral water. However, weakly basic Amberlite IRA-96 (110.8 mg/g) can separate FA more efficiently from potassium bicarbonate catholyte than Amberlite IRA-910 (99.9 mg/g) and Ambersep 900 (40.0 mg/g). As a result, competitive adsorption occurs in the presence of potassium bicarbonate catholyte, but the formic acid adsorption capacity is still sufficient for adequate separation.
20 FOSSIL-FUELED POWER PLANTS↗
Electronic structure in a transition metal dipnictide TaAs 2
Abstract The family of transition-metal dipnictides has been of theoretical and experimental interest because this family hosts topological states and extremely large magnetoresistance (MR). Recently, T a A s 2 , a member of this family, has been predicted to support a topological crystalline insulating state. Here, by using high-resolution angle-resolved photoemission spectroscopy (ARPES), we reveal both closed and open pockets in the metallic Fermi surface (FS) and linearly dispersive bands on the ( 2 ‾ 01 ) surface, along with the presence of extreme MR observed from magneto-transport measurements. A comparison of the ARPES results with first-principles computations shows that the linearly dispersive bands on the measured surface of T a A s 2 are trivial bulk bands. The absence of symmetry-protected surface state on the ( 2 ‾ 01 ) surface indicates its topologically dark nature. The presence of open FS features suggests that the open-orbit fermiology could contribute to the extremely large MR of T a A s 2 .
75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
Carbonic anhydrase textile structured packing for efficient CO 2 absorption in methyldiethanolamine solvent
Carbonic anhydrase (CA) is an attractive biodegradable catalyst for CO 2 absorption in solvent–based CO 2 capture. However, maintaining the stability of CA as a homogeneous component of the solvents is a challenge. Solvent regeneration temperature typically exceeds the enzyme thermal tolerance, which leads to CA deactivation. To reduce the need for frequent CA replenishment and to avoid inactive CA accumulation in the solvent, this work shows the benefits of an immobilization strategy where CA is fixed in a second–generation design of textile structured packing (CATSP–2) modules. The enzyme–immobilized packing showed 1.5 times better performance in CO 2 separation compared with traditional structured packing with a corresponding increased CO 2 loading in the rich solvent. The modules exhibited good CA activity retention of ~80% during the tests without any CA replenishment. As a result, applying CATSP–2 could potentially decrease the packing height and absorber column size for a lower cost per amount of CO 2 captured.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Intensified Catalytic Conversion of CO2 into High Value Chemicals
The utilization of CO2 produced from power generation plants as a feedstock for creating new valuable products offers a strategy to reduce GHG emissions, offset carbon capture costs, and facilitate the rebalancing of the carbon cycle. After considering the thermodynamic requirement of potential products from CO2 utilization and their market size, formic acid is a desirable target that offers widespread utility in industrial chemical production and chemical energy storage as a liquid fuel. To effectively utilize CO2 from power generation plants, UK proposes an enhanced bimetallic oxide carbon utilization process (EBOCU) that enables electrochemical CO2 conversion to formic acid. The UK intensified electrocatalytic process combines three main components: 1) a novel bimetallic oxide electrocatalyst; 2) a stable electrochemical reactor using robust electrodes; and 3) a pressurized electrochemical reactor. The output from this project showed the economic viability of producing high-value formic acid from CO2 to both offset the cost associated with post-combustion CCS and reduce GHG emissions. This project developed and screened a series engineered catalysts to selectively reduce CO2 directly to formic acid. The best performing catalyst based on formic acid production, stability, and Faradaic efficiency, was immobilized on carbon electrodes, and tested inside a flow through reactor. After lab-scale testing was completed, the experimental data was used to perform a Life-Cycle Analysis (LCA) and conduct an Initial Technical and Economic Feasibility Study. The LCA showed a pathway to a net negative CO2 utilization process with the incorporation of renewable energy, while the TEA showed the potential to produce formic acid below the current commercial price. The UK EBOCU process was successfully demonstrated at the TRL3 level and has a clear pathway to further development and contribution to the nation’s ambitious decarbonization goals.
20 FOSSIL-FUELED POWER PLANTS↗
Towards an Integrated Process for CO 2 Capture and Utilization: Cultivation of Scenedesmus acutus Using Gaseous CO 2 and NH 3
Integrating CO 2 scrubbing from flue gas with its utilization in algae cultivation represents a potential means of lowering the cost of CO 2 capture. Towards this goal, this study sought to assess the feasibility of using gaseous a CO 2 /NH 3 stream, derived from CO 2 capture using aqueous ammonia, as a C- and N-source for algae cultivation. Scenedesmus acutus was cultured in 800 mL photobioreactors using gaseous CO 2 /NH 3 in mole ratios varying from 7 to 18. Excellent growth of Scenedesmus acutus was observed, the average growth rate for CO 2 /NH 3 = 10 of 0.171 ± 0.015 g/L·day exceeding that obtained using 1% CO 2 /N 2 and urea as the N-source (0.099 ± 0.28 g/L·day). Under optimal growth conditions (CO 2 /NH 3 mole ratio of 10), CO 2 utilization ranged from 57% to 72%, while the NH 3 utilization was >90%. The CO 2 /NH 3 feed rate was also found to exert a significant effect on algae productivity, excessive feed rates leading to accumulation of NH 3 in the culture at concentrations that were toxic to the algae. Consequently, to avoid the toxic effects of high NH 3 concentrations (>2.0 mM), it proved necessary to balance the NH 3 supply with the algae growth rate so that excessive NH 3 accumulation was prevented. This indicates that for practical applications, a CO 2 /NH 3 feed control strategy would be required that takes into account the ammonium ion concentration in solution and the pH so as to avoid significant concentrations of free NH 3 . Furthermore, analysis of the harvested biomass revealed a high protein (≥ 47 wt%) and a low ash content (< 3.6 wt%), suggesting it would be well suited for use as animal feed or as a feedstock for the production of bioplastics.
03 NATURAL GAS↗
Electrochemical CO2 conversion to formic acid using engineered enzymatic catalysts in a batch reactor
Not Available
60 APPLIED LIFE SCIENCES↗
Micropatterning of alumina tubular membranes via laser carving for enhanced direct air capture
An approach for preparing and applying micropatterned alumina tubular membranes was developed for improved gas-liquid contact at low air pressure drop in direct air capture application. The paper demonstrated that the laser carving of micropatterns on the outer surface of the alumina tubular membranes could greatly increase their outer surface area and enhance gas-liquid turbulence for a reduced diffusion mass transfer resistance. Six kinds of micropattern configurations were fabricated and studied, including random and regular micropatterns. By introducing a 500-μm solid grid micropattern, the outer surface area doubles and enhances carbon dioxide capture efficiency from 61% to 97% after the membrane was hydrophobically modified with fluoroalkylsilane. Here, the air pressure drop through the tube lumen remained low even when the packing density increased from 382 to 906 m 2 /m 3 . The liquid entry pressure of this micropatterned membrane was the same after testing for 220 h running with the help of periodic drying.
20 FOSSIL-FUELED POWER PLANTS↗
Advancing Post-Combustion CO 2 Capture through Increased Mass Transfer and Lower Degradation
The over-arching goal of the proposed project is to develop three techniques to enable aqueous post-combustion CO 2 capture technologies to meet the DOE performance and cost targets of 90% CO 2 capture, 95% purity, at a cost of less than $30/tonne CO 2 captured. This will be accomplished by the development of materials and processes to increase mass transfer in the absorber and reduce the environmental impacts. While constantly working to reduce the cost of CO 2 capture via solvent development and process & heat integration, increasing CO 2 mass transfer through development of custom dynamic packing materials and tuning solvent physical properties may offer a route to increased solvent capacity, lower energy consumption and reduced aerosol formation. The environmental concerns that have been identified in amine-based CO 2 capture systems, nitrosamines specifically, are another critical element that will be addressed in this project. The specific objectives of the project were to: 1) conduct detailed studies to understand how solvent physical properties and aerosol formation are impacted by additives; 2) quantify the CO 2 mass transfer improvement from the dynamic polarity packing in the absorber and the additive-modified solvent using the existing UK bench-scale CO 2 capture unit; 3) quantify the energy consumption savings associated with enhanced mass transfer; 4) quantify the benefits of the UK’s electrochemical cell to decompose nitrosamines; and 5) collect the necessary information/data to conduct a high-level TEA assessment of the proposed technologies. The project involved the fabrication and installation of customized dynamic polarity packing and an investigation into the understanding of the impact of chemical additives on solvent properties to increase CO 2 mass transfer in the absorber column, and lastly the design of an electrochemical cell to decompose nitrosamines in a water wash. After both systems were fabricated, they were tested at UK facilities, including on the bench-scale CO 2 capture unit under parametric and long-term operation.
20 FOSSIL-FUELED POWER PLANTS↗
Efficient carbon capture using sub-textured polymer packing surfaces via 3D printing
Gas absorption is a common unit operation whose performance deeply relies on the gas liquid contact behavior. In this work, we report a solid polymeric surface feature containing microscale striation to improve the solid-liquid and gas-liquid contact and facilitate mass transfer. As a proof of concept, the surface feature is adopted for CO 2 capture absorber packing via 3D printing. Besides traditional embossing texture, an additional laminar striation is applied to the packing surface as a sub-texture. The packing shows notable CO 2 mass transfer increase without interfering with other key operating characteristics including pressure drop and liquid holdup. The improvement is based on the synergy of favorable wettability, thin liquid film and increased liquid mixing from rougher surface. In the demonstration test, the packing height could decrease by 33% using the advanced packing with same CO 2 removal, leading to a significant decrease in equipment size and capital expense for commercial CO 2 capture systems.
3D printing↗
Oxygen Solubility in Aqueous Amine Solvents with Common Additives Used for CO 2 Chemical Absorption
Major sources of anthropogenic CO 2 are power generation and transportation industries where researcher continue to explore CO 2 emission mitigation strategies as applied to these CO 2 sources through carbon capture, utilization, and sequestration (CCUS). The most mature CO 2 capture technology is post-combustion carbon capture (PCCC) using aqueous amine solutions/solvents, however solvent degradation and regeneration costs are slowing the widespread adoption of PCCC. Solvent degradation of the aqueous amine solutions is mainly caused from the temperature gradient between the absorber and stripper columns and common flue gas components such as SOx, NOx, and oxygen (O 2 ). The two main classifications of solvent degradation are thermal degradation, occurring when the amine reacts with itself at elevated temperatures and anaerobic conditions and oxidative degradation. Oxidative degradation reactions can occur from oxygen mass transfer and free radical oxidation. Metals, such as iron from the corrosion of steel structures used in industrial applications such as PCCC, can help to catalyze these reactions. Various oxidative degradation studies have shown how O 2 concentrations in flue gas and, to a lesser extent, temperature influence the extent of oxidative degradation. Accurately measuring the O 2 solubility, commonly referred to as dissolved oxygen (DO), in a quick, continuous, and efficient manner in aqueous amine solvents should contribute to determine the effectiveness of mitigation strategies for oxidative degradation. Knowing that commercial PCCC amine solvents contain components beyond water, amine, carbonate species and CO 2 , this investigation was conducted to determine the oxygen solubility changes of common aqueous amines solutions with commonly used and published solvent additives. The impact of carbon loadings with and without the additives was also examined. A commercial dissolved oxygen probe was used to measure the DO concentrations and compared them against standard Winkler Method titration values. The results show that antifoam shows minimal change in [DO]. MBT yielded lower DO values, and NaVO 3 showed a higher DO concentration due to interferences. These results indicate that most common amine solvent additives should be expected to minimally impact oxygen solubility and amine oxidative degradation.
60 APPLIED LIFE SCIENCES↗
Mass transfer intensification through increased surface wetting and liquid turbulence using 3D printing structured packing for CO2 capture
The absorber column is one of the most expensive pieces of equipment to construct in the solvent-based post-combustion carbon capture unit. In order to decrease the absorber size and reduce capital costs, novel polymer packings were proposed by enhancing surface wettability and local turbulence within liquid solvent. The novel packings intensify the mass transfer in CO2 absorption and show better separation efficiency than traditional structured packings. In this work, the economic influence of applying the more efficient packing with a shorter absorber column is studied in a techno-economic analysis for a carbon capture unit at a coal-fired power plant. The baseline case includes CO2 capture unit in a supercritical pulverized coal power plant to generate 650 MWe (net) of electricity, where the additional CO2 capture unit leads to 63.4% increase of LCOE. While implementing UK PCC with traditional and novel packings, there will be 47.2% and 46.4% LCOE increase separately, both of which are lower than the baseline value. Applying more efficient packing and smaller absorber could further lessen the LCOE increase. The UK PCC with traditional packings reduces CO2 capture cost by 23.4% and the application of the advanced packings allows to the reduction increases to 24.4%.
60 APPLIED LIFE SCIENCES↗
Electrochemical CO2 conversion to formic acid through the Andora Process
Electrochemical utilization or conversion of CO2 can be used to convert waste CO2 into targeted high-value and cost-effective commercial products. Conventional processes for CO2 conversion to fuel sources are challenging and expensive due to their requirement for high temperatures and pressures. Electrochemically, a catalyst can be used at a fixed applied potential to reduce CO2 to form a desired product with less competition at modest operating conditions. Formic acid (FA) has recently become a product of interest for CO2 conversion due to its potential for hydrogen storage and fuel cell applications. Electrochemically, FA is produced through a direct two-electron transfer process involving CO2 with a proton source, requiring less energy input and fewer reaction steps than traditional processes. However, there remain significant obstacles for the broader-scale implementation of CO2 on the market, including competition with unwanted CO and H, the presence of molecular oxygen, and stability of the electrocatalyst. In order to overcome some of these challenges, a new continuous flow Andora Process was developed consisting of two separate cells to decouple electrochemical reduction of the charge carrier with the FA production via an engineered catalyst. Recent experimental results show that with appropriate design changes and operating conditions to the flow system, FA production above 500 mM can be achieved along with efficiencies above 80%. TEA and LCA assessments of the Andora Process show a potential for the reduction in the GWP potential and cost saving compared to the current comparative formic acid production process.
60 APPLIED LIFE SCIENCES↗
Apparatus to remove harmful chemical species from industrial wastewater using iron-based products
A method and apparatus are provided for removing EPA regulated chemical species from industrial wastewater using green rust. The apparatus includes a green rust generator having an iron anode and a carbon cathode.
Gao, Xin↗
Enhanced Depolarized Electro-Membrane System (EDEMS) for Direct Capture of Carbon Dioxide from Ambient Air (Final Report)
The goal of this final project report is to summarize the work conducted on project DE-FE0031962. In accordance with the Statement of Project Objectives (SOPO), the University of Kentucky Center for Applied Energy Research (UK CAER) (Recipient) developed an intensified process to capture CO2 from ambient conditions (400 ppm CO2). The process combines low-temperature solvent-aided membrane capture with electrochemically-mediated solvent regeneration to simultaneously capture ambient CO2 while regenerating the solvent. The technology employs only two primary units (regenerator and absorber/contactor) while generating high purity hydrogen as a co-product that can be sold, used for energy storage, or cost-saving depolarization of the direct air capture (DAC) system during the grid peak demand, allowing for flexible operation. When depolarization is employed, the operating voltage is reduced by more than 1 V. Since the technology is powered directly by DC electricity, it can seamlessly tie in with power sources like solar cells without the need for AC/DC converters, therefore allowing for a remote operation to further mitigate greenhouse gas generation toward deploying a negative carbon emissions technology that is completely decoupled from the carbon emissions from the power source for the DAC unit. The project results verified that UK CAER’s integrated approach addressed the complexities of incumbent DAC systems by demonstrating at ambient conditions, including (1) low gas-side pressure-drop facile CO2 capture via a membrane contactor with in-situ generated hydroxide as capture solvent, (2) multi-functional electrochemical regenerator for hydroxide regeneration, CO2 concentration and hydrogen production, and (3) depolarization using cathode-produced hydrogen to reduce energy requirement. The EH&S Assessment of the process did not identify any obvious concern for the bench-scale operation and no apparent barriers to implementing UK CAER’s carbon capture and solvent regeneration system at a larger scale.
20 FOSSIL-FUELED POWER PLANTS↗
Electrochemical analysis of charge mediator product composition through transient model and experimental validation
Not provided.
Electrochemistry↗