Engineering topics

Thompson, F L

Publications and source records attributed to Thompson, F L.

11 records

NASA NTRS1940

Notes on the stalling of vertical tail surfaces and on fin design

A discussion is given of the important aspects of the stalling of vertical tail surfaces. The type of instability encountered is described and the possibilities of inadvertent occurrence are noted. The influence of directional flight tests on the behavior of a airplane when the tail stall takes place is discussed. In this connection, flight tests of a twin-engine airplane in which the vertical fin area was increased are cited. The reasons for inadequate directional stability in certain modern designs are accounted for and the properties and applications of dorsal fins are discussed. In addition, the chief factors regulating the requirements for conventional area are given, in which connection simplified criterion for directional stability is presented. It may be concluded that the stalling of vertical tail surfaces is not in itself a dangerous condition. Provided sufficient directional stability exists at large angles of sideslip, the tail stall may occur with modern airplanes, as with those of the past, without the knowledge or concern to the pilot.

Thompson, F L↗

NASA NTRS1937

The Measurement of Air Speed in Airplanes

Various methods of measuring the air speed of airplanes are described. Particular emphasis is placed on the procedure required to obtain precise measurements of speed by the use of the suspended Pitot-static head or the suspended static head. Typical calibration curves for service installations of Pitot-static heads are shown and the relation between errors in air speed and corresponding errors in observed altitude for such installations is discussed. There is included a brief discussion of various speed-course methods of measuring speed.

Thompson, F L↗

NASA NTRS1936

Procedure for Determining Speed and Climbing Performance of Airships

The procedure for obtaining air-speed and rate-of-climb measurements in performance tests of airships is described. Two methods of obtaining speed measurements, one by means of instruments in the airship and the other by flight over a measured ground course, are explained. Instruments, their calibrations, necessary correction factors, observations, and calculations are detailed for each method, and also for the rate-of-climb tests. A method of correction for the effect on density of moist air and a description of other methods of speed course testing are appended.

Thompson, F L↗

NASA NTRS1935

Air Conditions Close to the Ground and the Effect on Airplane Landings

This report presents the results of an investigation undertaken to determine the feasibility of making glide landings in gusty air. Wind velocities were measured at several stations between the ground and a height of 51 feet, and flight tests were made to determine the actual influence of gusts on an airplane gliding close to the ground.

Thompson, F L↗

NASA NTRS1934

Maneuverability Investigation of an O3U-1 Observation Airplane

This report presents the results of maneuverability tests of an O3U-1 observation airplane. This investigation is the third in a series of similar investigations requested by the Bureau of Aeronautics (Navy) for the purpose of comparing the maneuverability of different airplane types and to provide quantitative data for use in establishing a criterion or method for rating the maneuverability of an airplane. The two former investigations were conducted with the fighter types designated F6C-3 and F6C-4 and have been reported previously. Measurement of the air speed, the angular velocity, the linear acceleration, and positions of the controls were made during abrupt single-control maneuvers with three stop positions for each control, during steady horizontal turns for the determination of minimum radius, and during 180 degree turns by various methods. Flight-path coordinates in two dimensions were determined for the 180 degree turns by means of a special camera obscura designed for the previous investigation of the F6C-4 airplane. All maneuvers were performed at an altitude of approximately 3,000 feet.

Thompson, F L↗

NASA NTRS1932

The drag characteristics of several airships determined by deceleration tests

This report presents the results of deceleration tests conducted for the purpose of determining the drag characteristics of six airships. The tests were made with airships of various shapes and sizes belonging to the Army, the Navy, and the Goodyear-Zeppelin Corporation. Drag coefficients for the following airships are shown: Army TC-6, TC-10, and TE-2; Navy Los Angeles and ZMC-2; Goodyear Puritan. The coefficients vary from about 0.045 for the small blunt airships to 0.023 for the relatively large slender Los Angeles. This variation may be due to a combination of effects, but the most important of these is probably the effect of length-diameter ratio.

Thompson, F L↗

NASA NTRS1931

Lift and drag characteristics of a cabin monoplane

The results of flight tests conducted by the NACA to determine the lift and drag characteristics of a full-scale airplane are given herein. A Fairchild FC-2W2 cabin monoplane having a Gottingen 387 wing section was used for the tests. The maximum lift coefficient for the airplane is compared with that obtained for the Gottingen 387 airfoil in recent tests in the Variable Density Tunnel. The maximum lift coefficient for the airplane was found to be 1.50 and that for the airfoil 1.56. Although the flight tests were confined chiefly to glides with the propeller locked horizontally, data obtained with the propeller operating at zero thrust for a few angles of attack are also included.

Thompson, F L↗

NASA NTRS1931

Water Pressure Distribution on a Flying Boat Hull

This is the third in a series of investigations of the water pressures on seaplane floats and hulls, and completes the present program. It consisted of determining the water pressures and accelerations on a Curtiss H-16 flying boat during landing and taxiing maneuvers in smooth and rough water.

Thompson, F L↗

NASA NTRS1930

Water Pressure Distribution on a Twin-Float Seaplane

This is the second of a series of investigations to determine water pressure distribution on various types of seaplane floats and hulls, and was conducted on a twin-float seaplane. It consisted of measuring water pressures and accelerations on a TS-1 seaplane during numerous landing and taxiing maneuvers at various speeds and angles. The results show that water pressures as great as 10 lbs. per sq. in.may occur at the step in various maneuvers and that pressures of approximately the same magnitude occur at the stern and near the bow in hard pancake landings with the stern way down. At the other parts of the float the pressures are less and are usually zero or slightly negative for some distance abaft the step. A maximum negative pressure of 0.87 lb. Per square inch was measured immediately abaft the step. The maximum positive pressures have a duration of approximately one-twentieth to one-hundredth second at any given location and are distributed over a very limited area at any particular instant.

Thompson, F L↗

NASA NTRS1930

Full-Scale Turning Characteristics of the U.S.S. Los Angeles

This paper present a description of the method employed and results obtained in full-scale turning trials on the rigid airship U. S. S. "Los Angeles". The results of this investigation are not sufficiently comprehensive to permit definite conclusions as to the variation of turning characteristics with changes in speed and rudder angle. They indicate however, that the turning radius compares favorably with that for other large airships, that the radius is independent of the speed, that the position of the point of zero yaw is nearly independent of the rudder angle and air speed, and that a theoretical relation between radius and angle of yaw in a turn gives a close approximation to actuality.

Thompson, F L↗

NASA NTRS1929

Water-Pressure Distribution on Seaplane Float

The investigation presented in this report was conducted for the purpose of determining the distribution and magnitude of water pressures likely to be experienced on seaplane hulls in service. It consisted of the development and construction of apparatus for recording water pressures lasting one one-hundredth second or longer and of flight tests to determine the water pressures on a UO-1 seaplane float under various conditions of taxiing, taking off, and landing. The apparatus developed was found to operate with satisfactory accuracy and is suitable for flight tests on other seaplanes. The tests on the UO-1 showed that maximum pressures of about 6.5 pounds per square inch occur at the step for the full width of the float bottom. Proceeding forward from the step the maximum pressures decrease in magnitude uniformly toward the bow, and the region of highest pressures narrows toward the keel. Immediately abaft the step the maximum pressures are very small, but increase in magnitude toward the stern and there once reached a value of about 5 pounds per square inch. (author)

Thompson, F L↗