Engineering topics

Thomas, David J.

Publications and source records attributed to Thomas, David J..

17 records

NASA NTRS2004

Characterization of Ceramic Matrix Composite Vane Subelements Subjected to Rig Testing in a Gas Turbine Environment

Vane subelements were fabricated from a silicon carbide fiber-reinforced silicon carbide matrix (SiC/SiC) composite. A cross-sectional slice of an aircraft engine metal vane was the basis of the vane subelement geometry. To fabricate the small radius of the vane's trailing edge using stiff Sylramic SiC fibers, a unique SiC fiber architecture was developed. A test configuration for the vanes in a high pressure gas turbine environment was designed and fabricated. Testing was conducted using a pressure of 6 atm and combustion flow rate of 0.5 kg/sec, and consisted of fifty hours of steady state operation followed by 102 2-minute thermal cycles. A surface temperature of 1320 C was obtained for the EBC-coated SiC/SiC vane subelement. This paper will briefly discuss the vane fabrication, test configuration, and results of the vane testing. The emphasis of the paper is on characterization of the post-test condition of the vanes.

Verrilli, Michael↗

NASA NTRS2004

Probabilistic Residual Strength Model Developed for Life Prediction of Ceramic Matrix Composites

For the next generation of reusable launch vehicles, NASA is investigating introducing ceramic matrix composites (CMCs) in place of current superalloys for structural propulsion applications (e.g., nozzles, vanes, combustors, and heat exchangers). The higher use temperatures of CMCs will reduce vehicle weight by eliminating and/or reducing cooling system requirements. The increased strength-to-weight ratio of CMCs relative to superalloys further enhances their weight savings potential. However, in order to provide safe designs for components made of these new materials, a comprehensive life prediction methodology for CMC structures needs to be developed. A robust methodology for lifing composite structures has yet to be adopted by the engineering community. Current industry design practice continues to utilize deterministic empirically based models borrowed from metals design for predicting material life capabilities. The deterministic nature of these models inadequately addresses the stochastic character of brittle composites, and their empirical reliance makes predictions beyond the experimental test conditions a risky extrapolation. A team of engineers at the NASA Glenn Research Center has been developing a new life prediction engineering model. The Probabilistic Residual Strength (PRS) model uses the residual strength of the composite as its damage metric. Expected life and material strength are both considered probabilistically to account for the observed stochastic material response. Extensive experimental testing has been carried out on C/SiC (a candidate aerospace CMC material system) in a controlled 1000 ppm O2/argon environment at elevated temperatures of 800 and 1200 C. The test matrix was established to allow observation of the material behavior, characterization of the model, and validation of the model's predictive capabilities. Sample results of the validation study are illustrated in the graphs.

Thomas, David J.↗

NASA NTRS2004

Ceramic Matrix Composite Vane Subelement Testing in a Gas Turbine Environment

Vane subelements were fabricated from a silicon carbide fiber reinforced silicon carbide matrix (SiC/SiC) composite and were coated with an environmental barrier coating (EBC). A test configuration for the vanes in a gas turbine environment was designed and fabricated. Prior to testing, finite element analyses were performed to predict the temperatures and stress conditions present in vane during rig testing. This paper discusses the test configuration, the finite element analysis predictions, and results of the vane testing.

Verrilli, Michael↗

NASA NTRS2003

C/sic Life Prediction for Propulsion Applications

Accurate life prediction is critical to successful use of ceramic matrix composites (CMCs). The tools to accomplish this are immature and not oriented toward the behavior of carbon fiber reinforced silicon carbide (C/SiC), the primary system of interest for many reusable and single mission launch vehicle propulsion and airframe applications. This paper describes an approach and progress made to satisfy the need to develop an integrated life prediction system that addresses mechanical durability and environmental degradation of C/SiC.

Levine, Stanley R.↗

NASA NTRS2003

Ceramic Matrix Composites (CMC) Life Prediction Development - 2003

Levine, Stanley R.↗

NASA NTRS2002

C/sic Life Prediction for Propulsion Applications

Accurate life prediction is critical to successful use of ceramic matrix composites (CMC). The tools to accomplish this are immature and not oriented toward the behavior of carbon fiber reinforced silicon carbide (C/SiC), the primary system of interest for many reusable and single mission launch vehicle propulsion and airframe applications. This paper describes an approach and process made to satisfy the need to develop an integrated life prediction system that addresses mechanical durability and environmental degradation of C/SiC. Issues such as oxidation, steam and hydrogen effects on material behavior are discussed. Preliminary tests indicate that steam will aggressively remove SiC seal coat and matrix in line with past experience. The kinetics of water vapor reaction with carbon fibers is negligible at 600 C, but comparable to air attack at 1200 C. The mitigating effect of steam observed in fiber oxidation studies has also been observed in stress rupture tests. Detailed microscopy of oxidized specimens is being carried out to develop the oxidation model. Carbon oxidation kinetics are reaction controlled at intermediate temperatures and diffusion controlled at high temperatures (approximately 1000 C). Activation energies for T-300 and interface pyrolytic carbon were determined as key inputs to the oxidation model. Crack opening as a function of temperature and stress was calculated. Mechanical property tests to develop and verify the probabilistic life model are very encouraging except for residual strength prediction. Gage width is a key variable governing edge oxidation of seal coated specimens. Future efforts will include architectural effects, enhanced coatings, biaxial tests, and LCF. Modeling will need to account for combined effects.

Levine, Stanley R.↗

NASA NTRS2002

C/SIC Life Prediction for Propulsion Applications

Accurate life prediction is critical to successful use of ceramic matrix composites (CMC). The tools to accomplish this are immature and not oriented toward the behavior of carbon fiber reinforced silicon carbide (C/SiC), the primary system of interest for many reusable and single mission launch vehicle propulsion and airframe applications. This paper describes an approach and progress made to satisfy the need to develop an integrated life prediction system that addresses mechanical durability and environmental degradation of C/SiC. Issues such as oxidation, steam and hydrogen effects on material behavior are discussed. Preliminary tests indicate that stream will aggressively remove SiC seal coat and matrix in line with past experience. The kinetics of water vapor reaction with carbon fibers is negligible at 600 C, but comparable to air attack at 1200 C. The mitigating effect of steam observed in fiber oxidation studies has also been observed in stress rupture tests. Detailed microscopy of oxidized specimens is being carried out to develop the oxidation model. Carbon oxidation kinetics are reaction controlled at intermediate temperatures and diffusion controlled at high temperatures (approx. 1000 C). Activation energies for T-300 and interface pyrolytic carbon were determined as key inputs to the oxidation model. Crack opening as a function of temperature and stress was calculated. Mechanical property tests to develop and verify the probabilistic life model are very encouraging except for residual strength prediction. Gage width is a key variable governing edge oxidation of seal coated specimens. Future efforts will include architectural effects, enhanced coatings, biaxial tests, and LCF. Modeling will need to account for combined effects.

Levine, Stanley R.↗

NASA NTRS2002

Design and Analysis of UHTC Leading Edge Attachment

NASA Glenn Research Center was contacted to provide technical support to NASA Ames Research Center in the design and analysis of an ultra high temperature ceramic (UHTC) leading edge. UHTC materials are being considered for reusable launch vehicles because their high temperature capability may allow for un-cooled sharp leading edge designs. While ceramic materials have the design benefit of allowing subcomponents to run hot, they also provide a design challenge in that they invariably must be in contact with cooler subcomponents elsewhere in the structure. NASA Glenn Research Center proposed a modification to an existing attachment design. Thermal and structural analyses of the leading edge assembly were carried out using ABAQUS finite element software. Final results showed that the proposed modifications aided in thermally isolating hot and cold subcomponents and reducing bearing stresses at the attachment location.

Thomas, David J.↗

NASA NTRS2000

Ceramic Matrix Composites (CMC) Life Prediction Method Development

Advanced launch systems (e.g., Reusable Launch Vehicle and other Shuttle Class concepts, Rocket-Based Combine Cycle, etc.), and interplanetary vehicles will very likely incorporate fiber reinforced ceramic matrix composites (CMC) in critical propulsion components. The use of CMC is highly desirable to save weight, to improve reuse capability, and to increase performance. CMC candidate applications are mission and cycle dependent and may include turbopump rotors, housings, combustors, nozzle injectors, exit cones or ramps, and throats. For reusable and single mission uses, accurate prediction of life is critical to mission success. The tools to accomplish life prediction are very immature and not oriented toward the behavior of carbon fiber reinforced silicon carbide (C/SiC), the primary system of interest for a variety of space propulsion applications. This paper describes an approach to satisfy the need to develop an integrated life prediction system for CMC that addresses mechanical durability due to cyclic and steady thermomechanical loads, and takes into account the impact of environmental degradation.

Levine, Stanley R.↗

NASA NTRS1995

Analysis of the progressive failure of brittle matrix composites

This report investigates two of the most common modes of localized failures, namely, periodic fiber-bridged matrix cracks and transverse matrix cracks. A modification of Daniels' bundle theory is combined with Weibull's weakest link theory to model the statistical distribution of the periodic matrix cracking strength for an individual layer. Results of the model predictions are compared with experimental data from the open literature. Extensions to the model are made to account for possible imperfections within the layer (i.e., nonuniform fiber lengths, irregular crack spacing, and degraded in-situ fiber properties), and the results of these studies are presented. A generalized shear-lag analysis is derived which is capable of modeling the development of transverse matrix cracks in material systems having a general multilayer configuration and under states of full in-plane load. A method for computing the effective elastic properties for the damaged layer at the global level is detailed based upon the solution for the effects of the damage at the local level. This methodology is general in nature and is therefore also applicable to (0(sub m)/90(sub n))(sub s) systems. The characteristic stress-strain response for more general cases is shown to be qualitatively correct (experimental data is not available for a quantitative evaluation), and the damage evolution is recorded in terms of the matrix crack density as a function of the applied strain. Probabilistic effects are introduced to account for the statistical nature of the material strengths, thus allowing cumulative distribution curves for the probability of failure to be generated for each of the example laminates. Additionally, Oh and Finney's classic work on fracture location in brittle materials is extended and combined with the shear-lag analysis. The result is an analytical form for predicting the probability density function for the location of the next transverse crack occurrence within a crack bounded region. The results of this study verified qualitatively the validity of assuming a uniform crack spacing (as was done in the shear-lag model).

Thomas, David J.↗

NASA NTRS1993

Progressive matrix cracking in off-axis plies of a general symmetric laminate

A generalized shear-lag model is derived to determine the average through-the-thickness stress state present in a layer undergoing transverse matrix cracking, by extending the method of Lee and Daniels (1991) to a general symmetric multilayered system. The model is capable of considering cracking in layers of arbitrary orientation, states of general in-plane applied loading, and laminates with a general symmetric stacking sequence. The model is included in a computer program designed for probabilistic laminate analysis, and the results are compared to those determined with the ply drop-off technique.

Thomas, David J.↗

NASA NTRS1992

Load redistribution considerations in the fracture of ceramic matrix composites

Using a macroscopic viewpoint, composite laminae are homogeneous orthotropic solids whose directional strengths are random variables. Incorporation of these random variable strengths into failure models, either interactive or noninteractive, allows for the evaluation of the lamina reliability under a given stress state. Using a noninteractive criterion for demonstration purposes, laminate reliabilities are calculated assuming previously established load sharing rules for the redistribution of load as the failure of laminae occur. The matrix cracking predicted by ACK theory is modeled to allow a loss of stiffness in the fiber direction. The subsequent failure in the fiber direction is controlled by a modified bundle theory. Results are compared with previous models which did not permit separate consideration of matrix cracking, as well as to results obtained from experimental data. The effects of variations from the ideal physical geometry which is normally used to depict the matrix cracking are also studied.

Thomas, David J.↗

NASA NTRS1991

Reliability analysis of composite laminates with load sharing

By viewing a composite lamina as a homogeneous solid whose directional strengths are random variables, lamina reliability under multiaxial stresses may be determined using either an interactive or a noninteractive criterion. From the reliability values for the individual laminae comprising a given laminate, Thomas and Wetherhold (1991) have proposed a method for determining bounds for the overall laminate reliability. In this paper, simple physically plausible phenomenological rules are proposed for redistribution of load after a lamina has failed within the confines of a laminate. These rules are illustrated by application to (0/ +/-15)s and (90/ +/-45/0)s graphite/epoxy laminates, and the results are compared to the previously proposed bounds.

Wetherhold, Robert C.↗

NASA NTRS1991

Reliability analysis of ceramic matrix composite laminates

At a macroscopic level, a composite lamina may be considered as a homogeneous orthotropic solid whose directional strengths are random variables. Incorporation of these random variable strengths into failure models, either interactive or non-interactive, allows for the evaluation of the lamina reliability under a given stress state. Using a non-interactive criterion for demonstration purposes, laminate reliabilities are calculated assuming previously established load sharing rules for the redistribution of load as the failure of laminae occur. The matrix cracking predicted by ACK theory is modeled to allow a loss of stiffness in the fiber direction. The subsequent failure in the fiber direction is controlled by a modified bundle theory. Results using this modified bundle model are compared with previous models which did not permit separate consideration of matrix cracking, as well as to results obtained from experimental data.

Thomas, David J.↗

NASA NTRS1991

Reliability analysis of continuous fiber composite laminates

This paper describes two methods, the maximum distortion energy (MDE) and the principle of independent action (PIA), developed for the analysis of the reliability of a single continuous composite lamina. It is shown that, for the typical laminated plate structure, the individual lamina reliabilities can be combined in order to produce the upper and the lower bounds of reliability for the laminate, similar in nature to the bounds on properties produced from variational elastic methods. These limits were derived for both the interactive and the model failure considerations. Analytical expressions were also derived for the sensitivity of the reliability limits with respect to changes in the Weibull parameters and in loading conditions.

Thomas, David J.↗

NASA NTRS1990

Reliability analysis of continuous fiber composite laminates

A composite lamina may be viewed as a homogeneous solid whose directional strengths are random variables. Calculation of the lamina reliability under a multi-axial stress state can be approached by either assuming that the strengths act separately (modal or independent action), or that they interact through a quadratic interaction criterion. The independent action reliability may be calculated in closed form, while interactive criteria require simulations; there is currently insufficient data to make a final determination of preference between them. Using independent action for illustration purposes, the lamina reliability may be plotted in either stress space or in a non-dimensional representation. For the typical laminated plate structure, the individual lamina reliabilities may be combined in order to produce formal upper and lower bounds of reliability for the laminate, similar in nature to the bounds on properties produced from variational elastic methods. These bounds are illustrated for a (0/plus or minus 15)sub s Graphite/Epoxy (GR/EP) laminate. And addition, simple physically plausible phenomenological rules are proposed for redistribution of load after a lamina has failed. These rules are illustrated by application to (0/plus or minus 15)sub s and (90/plus or minus 45/0)sub s GR/EP laminates and results are compared with respect to the proposed bounds.

Thomas, David J.↗

NASA NTRS1990

Ceramic Matrix Composites (CMC) Life Prediction Development

Advanced launch systems will very likely incorporate fiber reinforced ceramic matrix composites (CMC) in critical propulsion and airframe components. The use of CMC will save weight, increase operating margin, safety and performance, and improve reuse capability. For reusable and single mission use, accurate life prediction is critical to success. The tools to accomplish this are immature and not oriented toward the behavior of carbon fiber reinforced silicon carbide (C/SiC), the primary system of interest for many applications. This paper describes an approach and progress made to satisfy the need to develop an integrated life prediction system that addresses mechanical durability and environmental degradation.

Levine, Stanley R.↗