Engineering topics

Thien, Austen

Publications and source records attributed to Thien, Austen.

5 records

DOE OSTI2023

In-Situ Detection and Prediction of WAAM Cross Feature Geometry

Abstract Wire arc additive manufacturing (WAAM) is increasingly used by manufacturers due to its relatively low cost and high deposition rate compared to other metal AM methods, but the parts produced by WAAM can be subject to localized variations in part quality. One such variation is the cross-feature defect, whereby a localized part height increase occurs due to the crossing of deposition toolpaths. Mitigation of this defect is typically achieved using manual path planning strategies, but closed-loop control is underutilized. Since the nature of this defect and of the WAAM process is such that the previous layer’s geometry influences that of the subsequent layer’s, the cross-feature defect geometry changes throughout the deposition. Therefore, any closed-loop control strategy will need to incorporate the dynamic trait of this defect. The present work seeks to implement an in-situ process modeling approach where a regression model can be continuously updated to predict the defect geometry of the subsequent deposition layer based on the historical process data. Several multi-layer cross-feature geometries are deposited and current, voltage, and optical camera data is taken for each layer. The resulting cross-feature geometries are characterized using 3D scanning and the performance and accuracy of the in-situ modeling approach is evaluated.

Thien, Austen↗

DOE OSTI2023

ON PROCESS STABILITY IN WAAM-CMT OF ALUMINUM ALLOYS

Wire-arc additive manufacturing (WAAM) has become a cost-efficient metal additive manufacturing process. However, depositing aluminum with WAAM is challenging due to its sensitivity to heat input (linear energy density), which can cause undesirable surface topology waviness if not controlled. Thus, a process window is needed that can produce stable geometry and deposition conditions while minimizing production times. In this study, 5183 aluminum alloy wire is used to deposit 10-layer walls with varying wire feed speeds (WFS) and traverse speeds (TS) (at a constant WFS/TS ratio) and varying interpass temperature (IPT). In-situ process data consisting of optical contact-tip-workpiece-distance (CTWD) and current/voltage measurements are collected to determine process condition stability throughout the build. Part geometry is measured using a 3D scanner and build porosity is characterized via digital X-ray. A process window is identified that produces stable surface topology and process conditions at a minimal production time.

aluminum alloy↗

DOE OSTI2021

The effect of WAAM process parameters on process conditions and production metrics in the fabrication of single-pass multi-layer wall artifacts

The present work seeks to understand the impact of varying dwell time and input deposition power on part quality and overall production time for wire arc additive manufacturing. In this work, multi-layer wall geometries were deposited under different input power conditions without affecting the material deposition rate by setting traverse speed and wire feed speed constant and varying the contact tip-to-workpiece distance and the deposition power settings. Current and voltage data and optical imaging of the deposition zone were captured in situ, and wall geometry was characterized using laser scanning, so to understand the applicability of these methods for determining part height in situ. Furthermore, the present results demonstrate that alternating dwell times with lower input deposition power can result in significantly reduced overall production time and minimal material underbuilding, despite increased deposition geometry width. Furthermore, it is shown that while elimination of process dwell results in severe underbuilding of the deposition, it also yields the highest production rate for a hybrid-finished (e.g., deposited, machined) wall in terms of mm in build direction per minute and the highest buy-to-fly ratio.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Surface Qualification Toolpath Optimization for Hybrid Manufacturing

Hybrid manufacturing machine tools have great potential to revolutionize manufacturing by combining both additive manufacturing (AM) and subtractive manufacturing (SM) processes on the same machine tool. A prominent issue that can occur when going from AM to SM is that the SM process toolpath does not account for geometric discrepancies caused by the previous AM step, which leads to increased production times and tool wear, particularly when wire-based directed energy deposition (DED) is used as the AM process. This work discusses a methodology for approximating a part’s surface topology using on-machine contact probing and formulating an optimized SM toolpath using the surface topology approximation. Three different geometric surface approximations were used: triangular, trapezoidal, and a hybrid of both. SM toolpaths were created using each geometric approximation and assessed according to three objectives: reducing total machining time, reducing surface roughness, and reducing cutting force. Different prioritization scenarios of the optimization goals were also investigated. The optimal surface approximation that yielded the most improvement in the optimization was determined to be the hybrid surface topology approximation. Furthermore, it was shown that when the machining time or cutting force optimization goals were prioritized, there was little improvement in the other optimization goals.

36 MATERIALS SCIENCE↗

DOE OSTI2021

IoT Devices and Applications for Wire-Based Hybrid Manufacturing Machine Tools

Hybrid manufacturing machine tools have the potential to be a disruptive technology as they can leverage the benefits of both additive and subtractive manufacturing by incorporating both processes on the same machine while limiting the downsides of the individual processes. Since these machines use two very disparate manufacturing processes and hybrid manufacturing is an emerging technology, it will be useful to monitor data coming from the machine and apply it to improve the manufacturing process, the operation of the machine, and to integrate the machine into the larger digital framework of Industrial Internet of Things (IoT). The present work discusses IoT devices that would be beneficial to add to a hybrid machine tool as well as applications for those devices. The proposed methods discussed in this work have not been experimentally implemented on a hybrid machine tool and so there are no performance data available yet. The hybrid machine tool used as a basis to generate these IoT applications is the Mazak VC-500A/5x AM Hot Wire Deposition, which is a 5-axis machine tool incorporated with a wire feedstock 4kW laser deposition system. Methodologies and applications will be outlined for machine health and process monitoring. Other areas covered include process benchmarking, secure networking options for the proposed IoT framework, and hybrid process improvement. Limitations of these methods and future work for new sensor devices and application areas is also discussed.

Thien, Austen↗