Engineering topics

Tevaarwerk, J. L.

Publications and source records attributed to Tevaarwerk, J. L..

10 records

NASA NTRS1990

The measurement, modelling and prediction of traction forces in a rocket propellant

Traction tests were performed on RPI, a common kerosene-based rocket propellant. Traction data on this fluid are required for purposes of turbopump bearing design, using such codes as SHABERTH. To obtain the traction data, an existing twin disk machine was used, operating under the side slip mode and using elliptical contacts. The resulting traction curves were reduced to fundamental fluid property parameters using the Johnson and Tevaarwerk traction model. Theoretical traction predictions were performed by back substitution of the fundamental properties into the traction model. Comparison of the predicted with the measured curves gives a high degree of confidence in the correctness of the traction model.

Tevaarwerk, J. L.↗

NASA NTRS1989

The measurement, modeling, and prediction of traction for rocket propellant 1

Traction tests were performed on RP-1, a common kerosene based rocket propellant. Traction data on this fluid are required for purposes of turbopump bearing design, using codes such as SHABERTH. To obtain the traction data, an existing twin disc machine was used, operating under the side slip mode and using elliptical contacts. The range of test variables were: contact peak Hertz stress from 1.0 to 2.0 GPa, disc surface speed from 10 to 50 m/s, fluid inlet temperature from 30 to 70 C, and with a contact aspect ratio of 1.7. The resulting traction curves were reduced to fundamental fluid property parameters using the Johnson and Tevaarwerk traction model. Theoretical traction predictions were performed by back substitution of the fundamental properties into the traction model. Comparison of the predicted with the measured curves gives a high degree of confidence in the correctness of the traction model. For purposes of input to the NASA SHABERTH program, the traction model was next used to predict the expected traction of RP-1 under line contact conditions.

Tevaarwerk, J. L.↗

NASA NTRS1985

Constitutive modelling of lubricants in concentrated contacts at high slide to roll ratios

A constitutive lubricant friction model for rolling/sliding concentrated contacts such as gears and cams was developed, based upon the Johnson and Tevaarwerk fluid rheology model developed earlier. The friction model reported herein differs from the earlier rheological models in that very large slide to roll ratios can now be accommodated by modifying the thermal response of the model. Also the elastic response of the fluid has been omitted from the model, thereby making it much simpler for use in the high slide to roll contacts. The effects of this simplification are very minimal on the outcome of the predicted friction losses (less than 1%). In essence then the lubricant friction model developed for the high slide to roll ratios treats the fluid in the concentrated contact as consisting of a nonlinear viscous element that is pressure, temperature, and strain rate dependent in its shear response. The fluid rheological constants required for the prediction of the friction losses at different contact conditions are obtained by traction measurements on several of the currently used gear lubricants. An example calculation, using this model and the fluid parameters obtained from the experiments, shows that it correctly predicts trends and magnitude of gear mesh losses measured elsewhere for the same fluids tested here.

Tevaarwerk, J. L.↗

NASA NTRS1985

Rolling, slip and traction measurements on low modulus materials

Traction and wear tests were performed on six low modulus materials (LMM). Three different traction tests were performed to determine the suitability of the material for use as traction rollers. These were the rolling, slip and endurance traction tests. For each material the combination LMM on LMM and LMM on steel were evaluated. Rolling traction test were conducted to determine the load - velocity limits, the rolling traction coefficient of the materials and to establish the type of failures that would result when loading beyond the limit. It was found that in general a simple constant rolling traction coefficient was enough to describe the results of all the test. The slip traction tests revealed that the peak traction coefficients were considerably higher than for lubricated traction contacts. The endurance traction tests were performed to establish the durability of the LMM under conditions of prolonged traction. Wear measurements were performed during and after the test. Energetic wear rates were determined from the wear measurements conducted in the endurance traction tests. These values show that the roller wear is not severe when reasonable levels of traction are transmitted.

Tevaarwerk, J. L.↗

NASA NTRS1985

Thermal traction contact performance evaluation under fully flooded and starved conditions

Ultra high speed traction tests were performed on two traction fluids commonly employed. Traction data on these fluids is required for purposes of traction drive design optimization techniques. To obtain the traction data, an existing twin disc traction test machine was employed. This machine was modified to accommodate the range of test variables. All the data reported was obtained under conditions of side slip, a technique whereby only low power levels are required to simulate real traction drive contacts. Theoretical traction predictions were performed for a representative number of curves that showed the influence of rolling velocity, of contact pressure and of aspect ratio. To establish the accuracy of the thermal model the predictions were performed ith increasing levels of independence of experimentally determined parameters. In the final resulting prediction only two non linear thermal parameters were used for the prediction of 15 different traction curves covering the entire range of variables as used in the investigation, with the exception of the influence of asperity traction. Comparison of these theoretical curves and corresponding experimental traces show very good agreement.

Tevaarwerk, J. L.↗

NASA NTRS1983

Subsurface stress evaluations under rolling/sliding contacts

A computer model has been developed for evaluating the subsurface stresses incurred within rolling/sliding (elastic) contacts. The model involves first defining the stress tensor at any point (x, y, or z) beneath the surface in terms of the surface stresses. The stress tensors are analyzed to determine the maximum shear stresses and stress reversals. As a result of computations with the model, several observations were made. For example, the maximum reversing shear stresses are on the plane of the orthogonal shear stress. Further, the magnitude of these stresses is not altered by friction. However, under very high friction (typical of dry contact) surface stresses can dominate over subsurface stresses.

Kannel, J. W.↗

NASA NTRS1983

Traction calculations and design data for two traction fluids

The rheological properties of the fluid under these certain conditions which precludes the use of most of the conventional instruments for steady state measurement were studied. The only suitable type of instrument is a disk machine where most of the conditions are the same of similar to those in traction drives. From the resulting traction tests, certain models are inferred. To the designer of traction drives, the traction behavior of the fluid under the severe conditions is of utmost importance because of the direct influence that it has on the efficiency, size, and life of a given drive.

Tevaarwerk, J. L.↗

NASA NTRS1981

Stress evaluations under rolling/sliding contacts

The state of stress beneath traction drive type of contacts were analyzed. Computing stresses and stress reversals on various planes for points beneath the surface were examined. The effect of tangential and axial friction under gross slip conditions is evaluated with the models. Evaluations were performed on an RC (rolling contact) tester configuration and it is indicated that the classical fatigue stresses are not altered by friction forces typical of lubricated contact. Higher values of friction can result in surface shear reversal that exceeds the stresses at the depth of maximum shear reversal under rolling contact.

Kannel, J. W.↗

NASA NTRS1981

Traction contact performance evaluation at high speeds

The results of traction tests performed on two fluids are presented. These tests covered a pressure range of 1.0 to 2.5 GPa, an inlet temperature range of 30 'C to 70 'C, a speed range of 10 to 80 m/sec, aspect ratios of .5 to 5 and spin from 0 to 2.1 percent. The test results are presented in the form of two dimensionless parameters, the initial traction slope and the maximum traction peak. With the use of a suitable rheological fluid model the actual traction curves measured can now be reconstituted from the two fluid parameters. More importantly, the knowledge of these parameters together with the fluid rheological model, allow the prediction of traction under conditions of spin, slip and any combination thereof. Comparison between theoretically predicted traction under these conditions and those measured in actual traction tests shows that this method gives good results.

Tevaarwerk, J. L.↗

NASA NTRS1979

Traction drive performance prediction for the Johnson and Tevaarwerk traction model

The fluid rheology model is used to investigate the traction behavior for typical traction drive contacts. The aspect ratio of the contact and the invariably present spin are investigated. Contacts with a low aspect ratio predict a superior performance in that they show less slip for the same degree of traction. Spin always has a diminishing effect on the traction at the same slip. At sufficiently high spin the model may be simplified to a limiting shear stress model. The conventional rigid plastic analysis applies here equally well.

Tevaarwerk, J. L.↗