Engineering Papers⌕ Search

Engineering topics

Terrence R. Meyer

Publications and source records attributed to Terrence R. Meyer.

15 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2023

Variably Premixed Rotating Detonation Engine for Evaluation of Detonation Cycle Dynamics

A variably premixed rotating detonation engine using gaseous hydrogen and air reactants is introduced to enable investigation of key cycle processes while varying the homogeneity of the reactant inlet conditions. Two chamber configurations are investigated, the first with reactants filling the entire span of a straight annular channel and the second with a slightly larger channel and a backward-facing step. The first configuration permits both premixed and non-premixed fuel injection, enabling mixing quality modulation. The second configuration is operated only at fully premixed conditions. Operating modes and detonation wave speeds are characterized using exhaust-plume imaging, while the chamber heat release field is captured by transverse imaging through a transparent outer body. Tests using the first configuration were characterized by unstable counterpropagating modes with low detonation wave speeds regardless of the state of premixing, while the second configuration rendered single-wave behavior with wave speeds up to 86% of the Chapman–Jouguet velocity. Comparisons with a simple computational fluid dynamics model of the second configuration indicate that reactant preheating significantly influences the detonation wave topology, highlighting the potential utility of the test platform for isolating key physics associated with the effects of reactant premixing, preheating, and chamber geometry on rotating detonation engine operation.

Detonation↗
NASA NTRSDate not supplied

Advanced Diagnostics For Megahertz Imaging Of Mixing, Fuel Spray, And Combustion Processes For Rotating Detonation Combustors

Recent advancements in megahertz rate, high-power, burst-mode laser technology are leveraged to perform and explore imaging measurements that spatially and temporally resolve the mixing, combustion, and detonation flow field in two laboratory-scale rotating detonation combustors (RDCs). In a non-premixed annular RDC, multiple imaging diagnostics are explored to investigate gaseous and liquid injector behavior, the detonation wave structure, and the propellant refill. In one instance, OH planar laser-induced fluorescence (OH-PLIF) imaging is performed up to a 2 MHz repetition rate to track the combustion products and reaction zone locations. In the same annular RDC, a single liquid fuel jet is injected, and laser-based 355-nm imaging of the fuel spray is performed up to a 1 MHz repetition rate. For this configuration, the annular RDC is used as a detonation driver to impose periodic detonation waves to interact with the fuel spray. Moreover, in this annular RDC, a range of tracer-based laser imaging measurements are explored to time-resolve the unsteady oxidizer air recovery and refill process. In a non-premixed linear RDC, planar imaging measurements of the fuel mixing are performed up to a 200 kHz repetition rate using PLIF of a tracer in the fuel supply. The fuel mixing imaging helps explain the origin of the observed pre and post wave burning, detonation structure, and enables quantifying injector recovery timescales. This paper will provide a high-level broad survey of diagnostics applied in these RDCs, lessons learned, and interesting observations.

Combustion↗
NASA NTRSDate not supplied

Time Resolved Visualization of A Liquid Jet in an RDE Using MHz Rate Diesel PLIF

The characterization of the dynamic response of liquid jets to transient detonation wave passage is critical for optimization and modeling of liquid fueled rotating detonation combustors. In this work, a rotating detonation combustor (RDC) is operated on hydrogen and air to sustain stable detonation waves that acts as a detonation driver and interact in a one-way coupled manner with a single liquid fuel jet that propagates into the combustion chamber with cycle periods of ~ 250 μs. Diesel is utilized as a realistic fuel surrogate with higher aromatic compounds to enable fluorescence excitation, using the 355 nm third harmonic output of a burst-mode Nd:YAG laser, imaged at rates up to 1 MHz. By optimizing the technique to accommodate orders of magnitude variations in the fuel density throughout the injection process, the PLIF data enable quantitative measurements including the refill time, the relative recovery between liquid and gaseous jets and jet trajectory across various momentum flux ratio. As the passage of the detonation wave imparts significant changes in the momentum flux ratio, the qualitative liquid break-up process and spatial distribution varies significantly in time. As the injection system recovers ~ 70% of the cycle period and return to a quasi-steady position and allow comparisons with theoretical jet trajectories. These data, enabled by ultra-high-speed PLIF imaging, represent some of the first detailed measurements for quantifying the dynamic response and recovery of liquid jets exposed to periodic detonations in an operating RDC.

Propulsion↗
NASA NTRSDate not supplied

Time Resolved Visualization of Liquid Jet Interaction With H2-Air Rotating Detonations Using MHz Rate Diesel PLIF

The characterization of the dynamic response of liquid jets to transient detonation wave passage is critical for optimization and modeling of liquid fueled rotating detonation combustors. In this work, a rotating detonation combustor (RDC) is operated on hydrogen and air to sustain stable detonation waves that acts as a detonation driver and interact in a one-way coupled manner with a single liquid fuel jet that propagates into the combustion chamber with cycle periods of ~ 250 μs. Diesel is utilized as a realistic fuel surrogate with higher aromatic compounds to enable fluorescence excitation, using the 355 nm thirdharmonic output of a burst-mode Nd:YAG laser, imaged at rates up to 1 MHz. By optimizing the technique to accommodate orders of magnitude variations in the fuel density throughout the injection process, the PLIF data enable quantitative measurements including the refill time, the relative recovery between liquid and gaseous jets and jet trajectory across various momentum flux ratio. As the passage of the detonation wave imparts significant changes in the momentum flux ratio, the qualitative liquid break-up process and spatial distribution varies significantly in time. As the injection system recovers ~ 70% of the cycle period and return to a quasi-steady position and allow comparisons with theoretical jet trajectories. These data, enabled by ultra-high-speed PLIF imaging, represent some of the first detailed measurements for quantifying the dynamic response and recovery of liquid jets exposed to periodic detonations in an operating RDC.

Propulsion↗
NASA NTRSDate not supplied

Advancements in Burst-Mode Filtered Rayleigh Scattering for High-Speed Gas-Phase Multi-Parameter Measurements

Filtered Rayleigh scattering (FRS) can be used for velocity, density, temperature, and/or pressure measurements over a wide range of non-reacting flow conditions as well as more limited reacting flow conditions. However, the application of FRS to gas-phase measurements in large-scale test facilities can be limited due to low signal levels, strong background interferences, or the requirement for multiple cameras and/or molecular filters to spectrally resolve the signal. This work focuses on the spectral characteristics and wavelength-agility of burst-mode lasers for use in FRS systems. These advancements could improve measurement capability and data quality in applications with high levels of stray background scattering as well as where increased temporal resolution is desirable, such as high-speed flows.

filtered Rayleigh scattering↗
NASA NTRSDate not supplied

High-Speed Visualization of Spray Breakup in a Rotating Detonation Combustor Using Laser Induced Fluorescence

Rotating detonation engines (RDEs) represent a novel propulsion technology where incoming reactants are consumed by a self-sustaining detonation wave that travels azimuthally around an annular combustion chamber. In theory, the operating mode of these devices approximates a constant-volume combustion Humphry cycle. This represents a 5-15% increase in thermal efficiency over current rockets and air breathing systems operating on constant-pressure combustion Brayton cycles. The use of liquid fuels in RDEs represent unique challenges in terms of performance and operability. However, the fundamental physics involved in spray breakup, evaporation, and combustion are not well understood inside these devices. This research seeks to provide direct insight into these processes by adding a single liquid fuel injector into an otherwise hydrogen-air RDE to evaluate the breakup and refill dynamics. Visualization is performed by 200-1000 kHz laser induced fluorescence of liquid phase diesel (355 nm) and or kerosene (266 nm).

Detonation↗
NASA NTRSDate not supplied

Demonstration of Frequency-Scanning Burst-mode Filtered Rayleigh Scattering for Multi-Parameter Gas-Phase Measurements

Filtered Rayleigh scattering (FRS) is a diagnostic technique used for measurements of macroscopic properties of a gas. The FRS signal is passed through a narrow bandwidth molecular filter, commonly gaseous iodine, to measure the broadening and Doppler-shift of the scattering light from the molecules of the gas flow. However, in single-frequency, intensity-based approaches, the effects of pressure, temperature, and velocity can be difficult to deconvolve. To overcome this challenge, frequency-scanning FRS has been used to quasi-spectrally resolve the signal. In this work, a frequency-scanned, burst-mode laser was used to perform scanning FRS in an underexpanded jet to measure temperature, pressure, and radial velocity at measurement rates up to 1 kHz which is ~100,000 times faster than prior implementations of scanning FRS.

filtered Rayleigh scattering↗
NASA NTRSDate not supplied

Characterization of an Optically Accessible RP/GOx Rotating Detonation Engine

The accurate characterization of the dynamic response of liquid jets to transient detonation wave passage is crucial for optimizing and modeling liquid-fueled rotating detonation combustors. To address this need, we have developed an optically accessible rocket RDE (RP-RDE), which utilizes liquid RP-1 and gaseous oxygen as propellants and operates at elevated pressures. The experimental setup features optical access from the oxidizer injection plenum to the combustor exit, allowing for detailed characterization of injection, mixing, and combustion processes and their impact on the detonation wave structure. To design and develop the liquid injection scheme for the RP-RDE test article, we employed a combined experimental and numerical approach that included cold-flow simulations. Our aim was to optimize the liquid injection process and ensure that the resulting fuel-oxidizer mixture is homogeneous and stable. To this end, high-speed optical imaging will be employed to provide qualitative visualization of the liquid and gaseous phases of the propellant as well as the local heat release during detonation wave propagation through the non-premixed medium. This work will provide critical insights into the behavior of the transient detonation waves in more relevant rocket conditions, which is essential for the optimization and modeling of rotating detonation combustors.

Propulsion↗
NASA NTRSDate not supplied

Characterization of Reactant Refill and Detonation Wave Dynamics in a GOx/Natural-gas RDRE Using Simultaneous High Repetition-Rate OH-PLIF and Chemiluminescence

The potential application of rotating detonation engines (RDEs) in rocket combustors hinges on a fundamental understanding of detonation wave structure and injector characteristics with fuel and oxidizer compositions relevant in rocket systems. Simultaneous 300 kHz-rate broadband OH* chemiluminescence and OH-PLIF imaging is employed in a fully optically accessible Natural Gas-GOx rotating detonation rocket engine (RDRE) to visualize reactant refill dynamics and detonation wave structure. A custom-built KTP-type optical parametric oscillator (OPO) is coupled with a nanosecond high-repetition-rate burst-mode laser to output284 nm light and target excitation of the Q1(9) transition in the OH radical. Significant deflagrative burning is observed throughout the chamber as a consequence of the oxygen-rich environment. Trailing Azimuthal Reflected Shock Combustion (ARSC) system, similar to those in a H2-air RDE are observed, burning unburned reactants in the region immediately following the primary detonation wave. Contact burning, as indicated in this study, does not seem to be a primary loss mechanism. The simultaneous measurement of OH and OH* show that axial locations exist in the refill process where OH radicals are present, and produced due to shear layer induced deflagration, however, these zones do not produce excited state OH*. While a deeper understanding of the underlying physics in RDRE systems requires further investigation, this work highlights a first-of-its-kind visualization of the turbulent combustion product field and reactant refill characteristics in this highly unsteady environment.

Propulsion↗
NASA NTRSDate not supplied

Time-Resolved OH-PLIF Assessment of Deflagrations Levels in a CH4-O2 Rotating Detonation Rocket Combustor

The parasitic loss incurred by deflagrative pre-burning is considered to be one of the key challenges to the effective implementation of rotating detonation engine (RDE) systems. Thus far, there have been relatively limited high fidelity, spatio-temporally resolved measurements of the pre-burning process as a function of the reactant conditions and composition within an RDE. In this work, simultaneous high-repetition-rate broadband OH* chemiluminescence and OH planar laser-induced fluorescence (PLIF) imaging are employed to investigate deflagrative burning dynamics in a fully optically accessible CH4-O2 RDE as compared to a H2-air systems under the same conditions. A custom-built optical parametric oscillator (OPO) is coupled with a high-repetition-rate burst-mode laser to generate the 284 nm source for the excitation of the Q1(9) transition of the OH radical. Significant deflagrative burning is observed throughout the chamber as a consequence of the oxygen-rich environment. Trailing wave systems that consume unburned reactants in the region immediately following the primary detonation wave are observed. The formation of a product gas recirculation zone that entrains and combusts incoming reactants is observed, and quantitative analysis is performed to gain valuable insight into deflagration characteristics. At an oxidizer mass flux of Gox ≈ 350kg/m2/s, it is found that the levels of pre-wave burning in CH4-O2 are a factor of ∼2-3 times higher than in H2-air in the region directly ahead of the detonation wave at a global equivalence ratio Φ ≈ 1.0. This study highlights the key roles of ignition delay and turbulent mixing of the combustion product and reactant fields on the levels of pre-burning and establishes a methodology for further investigation, such as for the effects of various RDE inlet configurations.

Propulsion↗
NASA NTRSDate not supplied

High-Speed Visualization of Spray Breakup and Velocity Estimation in a Rotating Detonation Combustor Using Laser Induced Fluorescence

The underlying physical processes that liquid fuel sprays undergo in rotating detonation engines, particularly breakup and combustion, are not well understood nor are the coupling effects between the detonation and the spray. In this work, a single liquid jet of liquid fuel is inserted into a hydrogen-air RDC in order to study repetitive-one way coupled detonation interactions. High speed laser induced fluorescence of Jet-A at 300 kHz is used to visualize the dynamic processes inside the RDC for up to 10 ms per test. The employed imaging schemes allowed for unique insight into the spreading of liquid fuel in the azimuthal-axial directions via volumetric laser illumination. The Jet-A velocity field was estimated using OpenOpticalFlow and the impulse events observed colloquially agree with prior work on this test platform.

Instrumentation↗