Engineering Papers⌕ Search

Engineering topics

Tennyson, R. C.

Publications and source records attributed to Tennyson, R. C..

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

Crashworthiness of light aircraft fuselage structures: A numerical and experimental investigation

The dynamic behavior of aircraft fuselage structures subject to various impact conditions was investigated. An analytical model was developed based on a self-consistent finite element (CFE) formulation utilizing shell, curved beam, and stringer type elements. Equations of motion were formulated and linearized (i.e., for small displacements), although material nonlinearity was retained to treat local plastic deformation. The equations were solved using the implicit Newmark-Beta method with a frontal solver routine. Stiffened aluminum fuselage models were also tested in free flight using the UTIAS pendulum crash test facility. Data were obtained on dynamic strains, g-loads, and transient deformations (using high speed photography in the latter case) during the impact process. Correlations between tests and predicted results are presented, together with computer graphics, based on the CFE model. These results include level and oblique angle impacts as well as the free-flight crash test. Comparisons with a hybrid, lumped mass finite element computer model demonstrate that the CFE formulation provides the test overall agreement with impact test data for comparable computing costs.

Nanyaro, A. P.↗
NASA NTRS1984

Development of failure criterion for Kevlar-epoxy fabric laminates

The development of the tensor polynomial failure criterion for composite laminate analysis is discussed. In particular, emphasis is given to the fabrication and testing of Kevlar-49 fabric (Style 285)/Narmco 5208 Epoxy. The quadratic-failure criterion with F(12)=0 provides accurate estimates of failure stresses for the Kevlar/Epoxy investigated. The cubic failure criterion was re-cast into an operationally easier form, providing the engineer with design curves that can be applied to laminates fabricated from unidirectional prepregs. In the form presented no interaction strength tests are required, although recourse to the quadratic model and the principal strength parameters is necessary. However, insufficient test data exists at present to generalize this approach for all undirectional prepregs and its use must be restricted to the generic materials investigated to-date.

Tennyson, R. C.↗
NASA NTRS1984

The effect of space environment exposure on the properties of polymer matrix composite materials (A0180)

The objective of this experiment is to determine the effect of various lengths of exposure to a space environment on the mechanical properties of selected commercial polymer matrix composite materials. Fiber materials will include graphite, boron, S-glass, and PRD-49. The mechanical properties to be investigated are orthotropic elastic constants, strength parameters (satisfying the tensor polynomial relation), coefficients of thermal expansion, impact resistance, crack propagation, and fracture toughness. In addition, the effect of laminate thickness on property changes will also be investigated.

Tennyson, R. C.↗
NASA NTRS1984

An atomic oxygen facility for studying polymer materials for spacecraft applications

A nozzle beam facility utilizing microwave discharge on a helium carrier gas seeded with oxygen to produce atomic oxygen fluxes of the order of 10 to the 15th power atoms/cu cm/sec is described. In addition, limited test results obtained from exposing a graphite/epoxy composite and Kapton (H) film are presented in terms of mass loss measurements and changes in surface morphology.

Tennyson, R. C.↗
NASA NTRS1984

Failure analysis for composite laminates

A discussion of the tensor polynomial failure criterion is presented together with a description of a biaxial compression test procedure used in the evaluation of the interaction strength parameters. In addition, a formulation for predicting the fatigue life of laminates is given based on the experimental evaluation of fatigue functions which are also utilized in a form of the tensor polynomial failure criterion as well. Experimental results are provided to compare with the fatigue life predictions and to demonstrate the effect of flaws and environment. Both bond-line defects in sandwich beam construction and inter-laminar disbond flaws are studied. Up to present, compressive strength test data have been obtained for ambient and elevated temperature, moisture-saturated conditions, including results from thermal-spike cycling simulating supersonic flight.

Tennyson, R. C.↗
NASA NTRS1983

Failure analysis of composite laminates including biaxial compression

This report describes a continued effort on the development and application of the tensor polynomial failure criterion for composite laminate analysis. In particular, emphasis is given to the design, construction and testing of a cross-beam laminate configuration to obtain "pure' biaxial compression failure. The purpose of this test case was to provide to permit "closure' of the cubic form of the failure surface in the 1-2 compression-compression quadrant. This resulted in a revised set of interaction strength parameters and the construction of a failure surface which can be used with confidence for strength predictions, assuming a plane stress state exists. Furthermore, the problem of complex conjugate roots which can occur in some failure regions is addressed and an "engineering' interpretation is provided. Results are presented illustrating this behavior and the methodology for overcoming this problem is discussed.

Tennyson, R. C.↗
NASA NTRS1980

Application of the cubic polynomial strength criterion to the failure analysis of composite materials

A comparative failure analysis is presented based on the application of quadratic and cubic forms of the tensor polynomial lamina strength criterion to various composite structural configurations in a plane stress state. Failure loads have been predicted for off-angle laminates under simple loading conditions and for symmetric-balanced laminates subject to varying degrees of biaxial tension, including configurations subject to multimode failures. Some experimental data are also provided to support these calculations. From these results, the necessity of employing a cubic strength criterion to accurately predict the failure of composite laminae is demonstrated.

Tennyson, R. C.↗
NASA NTRS1978

Evaluation of the tensor polynomial failure criterion for composite materials

A comprehensive experimental and analytical evaluation of the tensor polynomial failure criterion was undertaken to determine its capability for predicting the ultimate strength of laminated composite structures subject to a plane stress state. Results are presented demonstrating that a quadratic formulation is too conservative and a cubic representation is required. Strength comparisons with test data derived from glass/epoxy and graphite/epoxy tubular specimens are also provided to validate the cubic strength criterion.

Tennyson, R. C.↗
NASA NTRS1978

Thermal-vacuum facility with in-situ mechanical loading

The paper describes a thermal-vacuum space simulator used to assess property changes of fiber-reinforced polymer composite systems. The facility can achieve a vacuum of approximately .0000001 torr with temperatures ranging from -200 to +300 F. Some preliminary experimental results are presented for materials subjected to thermal loading up to 200 F. The tests conducted include the evaluation of matrix modulus and strength, coefficients of thermal expansion, and fracture toughness. Though the experimental program is at an early stage, the data appear to indicate that these parameters are influenced by hard vacuum.

Tennyson, R. C.↗
NASA NTRS1977

Experimental evaluation of the tensor polynomial criterion for designing composite structures

A comprehensive experimental and analytical evaluation of the tensor polynomial failure criterion was undertaken to determine its capability for predicting the ultimate strength of a composite limina subject to a plane stress state. Results are presented demonstrating that a quadratic formulation is too conservative and a cubic representation is required. Strength comparisons with test data derived from glass/epoxy and graphite/epoxy tubular specimens are also provided to validate the cubic strength criterion. Environmental effects including ambient temperature, exposure to vacuum, length of post-cure time, and rate of cool down were also investigated. Behavior changes associated with polymer (epoxy) matrix composites were determined in terms of variations in stiffness and tensile strength.

Tennyson, R. C.↗
NASA NTRS1975

Experimental evaluation of the tensor polynomial failure criterion for the design of composite structures

The experimental measures and techniques are described which are used to obtain the strength tensor components, including cubic terms. Based on a considerable number of biaxial pressure tests together with specimens subjected to a constant torque and internal pressure, a modified form of the plane stress tensor polynomial failure equation was obtained that was capable of predicting ultimate strength results well. Preliminary data were obtained to determine the effect of varying post cure times and ambient temperatures (-80 F to 250 F) on the change in two tensor strength terms, F sub 2 and F sub 22. Other laminate configurations yield corresponding variations for the remaining strength parameters.

Tennyson, R. C.↗
NASA NTRS1975

Buckling of laminated composite cylinders - A review

A brief review of the available static buckling theory for both geometrically 'perfect' and 'imperfect' anisotropic composite circular cylinders is presented for various loading configurations. For comparison purposes, relevant experimental data are discussed, including recent combined loading test results and recommendations are made concerning the design of composite cylinders.

Tennyson, R. C.↗