Engineering topics
Publications and source records attributed to Taylor, C. M..
Finite-element computer program enables analysis of distortions and stresses occurring in components having relative interference. Program restricts itself to simple elements and axisymmetric loading situations. External inertial and thermal loads may be applied in addition to forces arising from interference conditions.
The influence of geometry on the isothermal hydrodynamic film separating two rigid solids was investigated. Pressure-viscosity effects were not considered. The minimum film thickness is derived for fully flooded conjunctions by using the Reynolds boundary conditions. It was found that the minimum film thickness had the same speed, viscosity, and load dependence as Kapitza's classical solution. However, the incorporation of Reynolds boundary conditions resulted in an additional geometry effect. Solutions using the parabolic film approximation are compared with those using the exact expression for the film in the analysis. Contour plots are shown that indicate in detail the pressure developed between the solids.
The influence of geometry on the isothermal hydrodynamic film separating two rigid solids was investigated. Pressure-viscosity effects were not considered. The minimum film thickness is derived for fully flooded conjunctions by using the Reynolds conditions. It was found that the minimum film thickness had the same speed, viscosity, and load dependence as Kapitza's classical solution. However, the incorporation of Reynolds boundary conditions resulted in an additional geometry effect. Solutions using the parabolic film approximation are compared with those using the exact expression for the film in the analysis. Contour plots are shown that indicate in detail the pressure developed between the solids.
A ceramic/metallic aircraft gas turbine outer gas path seal designed for improved engine performance was studied. Transient temperature and stress profiles in a test seal geometry were determined by numerical analysis. During a simulated engine deceleration cycle from sea-level takeoff to idle conditions, the maximum seal temperature occurred below the seal surface, therefore the top layer of the seal was probably subjected to tensile stresses exceeding the modulus of rupture. In the stress analysis both two- and three-dimensional finite element computer programs were used. Predicted trends of the simpler and more easily usable two-dimensional element programs were borne out by the three-dimensional finite element program results.
Explore the source record for details and available documents.
The elastic distortion of the inner ring of an experimental 3,000,000 DN roller bearing is investigated analytically. The geometry of this bearing is unusually complex and for this reason a bearing with an axially symmetric inner ring and shaft is also analyzed. Only the inner ring and shaft are considered using a two-dimensional finite element computer program which enables interference between these components to be accommodated. The results for the experimental bearing suggest that elastic distortions are modest in relation to the design clearances. However, the variation of the radial deflection of the raceway may be significant for some circumstances and the interference fit adopted between the ring and shaft appears to be questionably low.
The elastic distortion of the inner ring of an experimental roller bearing is investigated analytically. The geometry of the experimental bearing is unusually complex, and for this reason a bearing with an axially symmetric inner ring is also analyzed. Only the inner ring and shaft are considered using a two dimensional finite element program that can accommodate interference between these components. The results suggest that the elastic distortions are modest in relation to the design clearances associated with the experimental bearing. The variation of the radial deflection of the raceway may, however, be significant in some circumstances.
A finite element computer program which enables the analysis of distortions and stresses occurring in compounds having a relative interference is presented. The program is limited to situations in which the loading is axisymmetric. Loads arising from the interference fit(s) and external, inertial, and thermal loadings are accommodated. The components comprise several different homogeneous isotropic materials whose properties may be a function of temperature. An example illustrating the data input and program output is given.
In the analysis of distortions occurring in rolling-element bearings, it is common to neglect the stiffening effect of shafting outside the bearing region. The magnitude of such an effect will be dependent primarily on the bearing width-to-bore ratio, the shaft geometry, and the location of the bearing on the shaft. An estimate is given of the stiffening effect for a wide range of these variables. In addition, brief consideration is given to the parallel situation existing at the outer ring housing.
A ceramic/metallic aircraft gas turbine outer gas path seal designed to enable improved engine performance is studied. Flexible numerical analysis schemes suitable for the determination of transient temperature profiles and thermal stress distributions in the seal are outlined. An estimation of the stresses to which a test seal is subjected during simulated engine deceleration from sea level takeoff to idle conditions is made. Experimental evidence has indicated that the surface layer of the seal is probably subjected to excessive tensile stresses during cyclic temperature loading. This assertion is supported by the analytical results presented. Brief consideration is given to means of mitigating this adverse stressing.
Explore the source record for details and available documents.