Engineering Papers⌕ Search

Engineering topics

Tang, T

Publications and source records attributed to Tang, T.

Progress with PXIE MEBT Chopper

A capability to provide a large variety of bunch patterns is crucial for the concept of the Project X serving MW-range beam to several experiments simultaneously. This capability will be realized by the Medium Energy Beam Transport's (MEBT) chopping system that will divert 80% of all bunches of the initially 5 mA, 2.1 MeV CW 162.5 MHz beam to an absorber according to a pre-programmed bunch-by-bunch selection. Being considered one of the most challenging components, the chopping system will be tested at the Project X Injector Experiment (PXIE) facility that will be built at Fermilab as a prototype of the Pojrect X front end. The bunch deflection will be made by two identical sets of travelling-wave kickers working in sync. Presently, two versions of the kickers are being investigated: a helical 200 Ohm structure with a switching-type 500 V driver and a planar 50 Ohm structure with a linear {+-} 250 V amplifier. This paper describes the chopping system scheme and functional specifications for the kickers, present results of electromagnetic measurements of the models, discuss possible driver schemes, and show a conceptual mechanical design.

43 PARTICLE ACCELERATORS↗

A Solid-State Nanosecond Beam Kicker Modulator Based on the DSRD Switch

A fast solid-state beam kicker modulator is under development at the SLAC National Accelerator Laboratory. The program goal is to develop a modulator that will deliver 4 ns, {+-}5 kV pulses to the ATF2 damping ring beam extraction kicker. The kicker is a 50 {Omega}, bipolar strip line, 60 cm long, fed at the downstream end and terminated at the upstream end. The bunch spacing in the ring is 5.6 ns, bunches are removed from the back end of the train, and there is a gap of 103.6 ns before the next train. The modulator design is based on an opening switch topology that uses Drift Step Recovery Diodes as the opening switches. The design and results of the modulator development are discussed. There are many applications that benefit from very fast high power switching. However, at MW power levels and nanosecond time scales, solid state options are limited. One option, the Drift Step Recovery Diode (DSRD) has been demonstrated as capable of blocking thousands of volts and switching in nanosecond to sub-nanosecond ranges. When used as an opening switch, the DSRD exhibits a very fast turn off transient. The process is described in detail by its pioneers in [5,6]. In essence, charge is pumped into and then extracted from the DSRD under pulsed conditions. The turn off transient occurs precisely when the pumped charge is equal to the extracted charge and the DSRD is switched off. At the SLAC National Accelerator Laboratory, a DSRD is being used as an opening switch in the development of a fast kicker modulator. The modulator is designed to create {+-}5kV pulses with <1ns rise and fall time on a 50{Omega} strip line kicker. As is common in beam optics, the absence of power in the kicker before and after the pulse is very important. The entire {+-}5kV kicker modulator is composed of two identical 5kV pulsing circuits, each with its own DSRD component. This paper describes the modulator topology and the status of tests on one of the two 5kV pulse circuits.

43 PARTICLE ACCELERATORS↗

Analysis of the Ultra-fast Switching Dynamics in a Hybrid MOSFET/Driver

The turn-on dynamics of a power MOSFET during ultra-fast, {approx} ns, switching are discussed in this paper. The testing was performed using a custom hybrid MOSFET/Driver module, which was fabricated by directly assembling die-form components, power MOSFET and drivers, on a printed circuit board. By using die-form components, the hybrid approach substantially reduces parasitic inductance, which facilitates ultra-fast switching. The measured turn on time of the hybrid module with a resistive load is 1.2 ns with an applied voltage of 1000 V and drain current of 33 A. Detailed analysis of the switching waveforms reveals that switching behavior must be interpreted differently in the ultra-fast regime. For example, the gate threshold voltage to turn on the device is observed to increase as the switching time decreases. Further analysis and simulation of MOSFET switching behavior shows that the minimum turn on time scales with the product of the drain-source on resistance and drain-source capacitance, R{sub DS(on)}C{sub OSS}. This information will be useful in power MOSFET selection and gate driver design for ultra-fast switching applications.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

P1-Marx Modulator for the ILC

A first generation prototype, P1, Marx-topology klystron modulator has been developed at the SLAC National Accelerator Laboratory for the International Linear Collider (ILC) project. It is envisioned as a lower cost, smaller footprint, and higher reliability alternative to the present, bouncer-topology, baseline design. The application requires 120 kV (+/-0.5%), 140 A, 1.6 ms pulses at a rate of 5 Hz. The Marx constructs the high voltage pulse by combining, in series, a number of lower voltage cells. The Marx employs solid state elements; IGBTs and diodes, to control the charge, discharge and isolation of the cells. Active compensation of the output is used to achieve the voltage regulation while minimizing the stored energy. The P1-Marx has been integrated into a test stand with a 10 MW L-band klystron, where each is undergoing life testing. A review of the P1-Marx design and its operational history in the L-band test stand are presented.

43 PARTICLE ACCELERATORS↗

Design Considerations for a PEBB-Based Marx-Topology ILC Klystron Modulator

The concept of Power Electronic Building Blocks (PEBBs) has its origin in the U.S. Navy during the last decade of the past century. As compared to a more conventional or classical design approach, a PEBB-oriented design approach combines various potential advantages such as increased modularity, high availability and simplified serviceability. This relatively new design paradigm for power conversion has progressively matured since then and its underlying philosophy has been clearly and successfully demonstrated in a number of real-world applications. Therefore, this approach has been adopted here to design a Marx-topology modulator for an International Linear Collider (ILC) environment where easy serviceability and high availability are crucial. This paper describes various aspects relating to the design of a 32-cell Marx-topology ILC klystron modulator. The concept of nested droop correction is introduced and illustrated. Several design considerations including cosmic ray withstand, power cycling capability, fault tolerance, etc., are discussed. Details of the design of a Marx cell PEBB are included.

43 PARTICLE ACCELERATORS↗

Hybrid MOSFET/Driver for Ultra-Fast Switching

The ultra-fast switching of power MOSFETs, in about 1ns, is very challenging. This is largely due to the parasitic inductance that is intrinsic to commercial packages used for both MOSFETs and drivers. Parasitic gate and source inductance not only limit the voltage rise time on the MOSFET internal gate structure but can also cause the gate voltage to oscillate. This paper describes a hybrid approach that substantially reduces the parasitic inductance between the driver and MOSFET gate, as well as between the MOSFET source and its external connection. A flip chip assembly is used to directly attach a die-form power MOSFET and driver on a PCB. The parasitic inductances are significantly reduced by eliminating bond wires and minimizing lead length. The experimental results demonstrate ultra-fast switching of the power MOSFET with excellent control of the gate-source voltage.

42 ENGINEERING↗

ILC Marx Modulator Development Program Status

Development of a first generation prototype (P1) Marx-topology klystron modulator for the International Linear Collider is nearing completion at the Stanford Linear Accelerator Center. It is envisioned as a smaller, lower cost, and higher reliability alternative to the present, bouncer-topology, 'Baseline Conceptual Design'. The Marx presents several advantages over conventional klystron modulator designs. It is physically smaller; there is no pulse transformer (quite massive at ILC parameters) and the energy storage capacitor bank is quite small, owing to the active droop compensation. It is oil-free; voltage hold-off is achieved using air insulation. It is air cooled; the secondary air-water heat exchanger is physically isolated from the electronic components. The P1-Marx employs all solid state elements; IGBTs and diodes, to control the charge, discharge and isolation of the cells. A general overview of the modulator design and the program status are presented.

43 PARTICLE ACCELERATORS↗