Engineering Papers⌕ Search

Engineering topics

Talbot, P. D.

Publications and source records attributed to Talbot, P. D..

14 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

Helicopter rotor and engine sizing for preliminary performance estimation

Methods are presented for estimating some of the more fundamental design variables of single-rotor helicopters (tip speed, blade area, disk loading, and installed power) based on design requirements (speed, weight, fuselage drag, and design hover ceiling). The well-known constraints of advancing-blade compressibility and retreating-blade stall are incorporated into the estimation process, based on an empirical interpretation of rotor performance data from large-scale wind-tunnel tests. Engine performance data are presented and correlated with a simple model usable for preliminary design. When approximate results are required quickly, these methods may be more convenient to use and provide more insight than large digital computer programs.

Talbot, P. D.↗
NASA NTRS1986

Flight test planning and parameter extraction for rotorcraft system identification

The present study is concerned with the mathematical modelling of aircraft dynamics on the basis of an investigation conducted with the aid of the Rotor System Research Aircraft (RSRA). The particular characteristics of RSRA make it possible to investigate aircraft properties which cannot be readily studied elsewhere, for example in the wind tunnel. The considered experiment had mainly the objective to develop an improved understanding of the physics of rotor flapping dynamics and rotor loads in maneuvers. The employed approach is based on a utilization of parameter identification methodology (PID) with application to helicopters. A better understanding of the contribution of the main rotor to the overall aircraft forces and moments is also to be obtained. Attention is given to the mathematical model of a rotorcraft system, an integrated identification method, flight data processing, and the identification of RSRA mathematical models.

Wang, J. C.↗
NASA NTRS1986

Real-time simulator for helicopter rotor wind-tunnel operations

This paper describes the elements and operation of a simulator that is being used to train operators of the Rotor Test Apparatus (RTA) in the large-scale 40- by 80-Foot Wind Tunnel at Ames Research Center. The simulator, named TUTOR (for Tunnel Utilization Trainer with Operating Rotor) duplicates the controls of the rotor and its dynamic behavior, as well as the wind-tunnel controls. The simulation software uses a preexisting blade-element model of a four-bladed rotor with flapping and lead-lag degrees of freedom. Equations were developed for all hardware and controls of the RTA and of the wind tunnel that are normally required to perform a wind-tunnel test of a helicopter rotor. The simulator hardware consists of consoles designed to have the same appearance and functions as those in the control room of the 40- by 80-Foot Wind Tunnel, allowing input from three operators who normally establish the required operating conditions during a test run. Normal operating procedures can be practiced, as well as simulated emergencies such as rotor power failure.

Talbot, P. D.↗
NASA NTRS1983

Effect of buoyancy and power design parameters on hybrid airship performance

The effects of several design parameters on the performance of hybrid airships having rotors and propellers were examined with a simple mathematical model. The parameters included buoyancy ratio, Froude number, ratio of rotor power to total power, and rotor shaft tilt. Performance variations resulting from changes in these parameters were calculated, and are presented and discussed. Performance quantities included best climb rate, equivalent vehicle L/D, and maximum speed. Performance at all speeds between hover and maximum speed was found to be sensitive to power distribution between rotors and propellers, and to rotor shaft tilt.

Talbot, P. D.↗
NASA NTRS1982

A mathematical model of a single main rotor helicopter for piloted simulation

A mathematical model, suitable for piloted simulation of the flying qualities of helicopters, is a nonlinear, total force and moment model of a single main rotor helicopter. The model has ten degrees of freedom: six rigid body, three rotor flapping, and the rotor rotational degrees of freedom. The rotor model assumes rigid blades with rotor forces and moments radially integrated and summed about the azimuth. The fuselage aerodynamic model uses a detailed representation over a nominal angle of attack and sideslip range of + or - 15 deg., as well as a simplified curve fit at large angles of attack or sideslip. Stabilizing surface aerodynamics are modeled with a lift curve slope between stall limits and a general curve fit for large angles of attack. A generalized stability and control augmentation system is described. Additional computer subroutines provide options for a simplified engine/governor model, atmospheric turbulence, and a linearized six degree of freedom dynamic model for stability and control analysis.

Talbot, P. D.↗
NASA NTRS1981

Rotorcraft researchers and operators - Is there is common ground

An investigation is conducted concerning the extent to which a program for rotorcraft research presented by NASA meets the user needs. Problems of civil operators are examined, taking into account powerplants, reliability and maintainability, environment, noise and vibration, and lack of space for passengers' baggage. A description of applicable technology is provided, giving attention to aerodynamics and structures, propulsion, power transfer methodology, flight control, avionic systems, human factors, and vehicle configurations. One of the most difficult challenges in trying to bring research to bear on operator problems is that in general researchers are working on long-term solutions while operators are seeking short-term answers. Attention is also given to potential technological bright spots, higher risk technologies, highest technological risks, and advanced vehicle configurations.

Talbot, P. D.↗
NASA NTRS1980

Effects of rotor parameter variations on handling qualities of unaugmented helicopters in simulated terrain flight

A coordinated analysis and ground simulator experiment was performed to investigate the effects on single rotor helicopter handling qualities of systematic variations in the main rotor hinge restraint, hub hinge offset, pitch-flap coupling, and blade lock number. Teetering rotor, articulated rotor, and hingeless rotor helicopters were evaluated by research pilots in special low level flying tasks involving obstacle avoidance at 60 to 100 knots airspeed. The results of the experiment are in the form of pilot ratings, pilot commentary, and some objective performance measures. Criteria for damping and sensitivity are reexamined when combined with the additional factors of cross coupling due to pitch and roll rates, pitch coupling with collective pitch, and longitudinal static stability. Ratings obtained with and without motion are compared. Acceptable flying qualities were obtained within each rotor type by suitable adjustment of the hub parameters, however, pure teetering rotors were found to lack control power for the tasks. A limit for the coupling parameter L sub q/L sub p of 0.35 is suggested.

Talbot, P. D.↗
NASA NTRS1979

A piloted simulator study on augmentation systems to improve helicopter flying qualities in terrain flight

Four basic single-rotor helicopters, one teetering, on articulated, and two hingeless, which were found to have a variety of major deficiencies in a previous fixed-based simulator study, were selected as baseline configurations. The stability and control augmentation systems (SCAS) include simple control augmentation systems to decouple pitch and yaw responses due to collective input and to quicken the pitch and roll control responses; SCAS of rate-command type designed to optimize the sensitivity and damping and to decouple the pitch-roll due to aircraft angular tate; and attitude-command type SCAS. Pilot ratings and commentary are presented as well as performance data related to the task. SCAS control usages and their gain levels associated with specific rotor types are also discussed.

Chen, R. T. N.↗
NASA NTRS1978

A simple method for estimating minimum autorotative descent rate of single rotor helicopters

Flight test results of minimum autorotative descent rate are compared with calculations based on the minimum power required for steady level flight. Empirical correction factors are derived that account for differences in energy dissipation between these two flight conditions. A method is also presented for estimating the minimum power coefficient for level flight for any helicopter for use in the empirical estimation procedure of autorotative descent rate.

Talbot, P. D.↗
NASA NTRS1978

A piloted simulator investigation of augmentation systems to improve helicopter nap-of-the-earth handling qualities

A piloted simulation study assessed various levels of stability and control augmentation designed to improve the handling qualities of several helicopters in nap-of-the-earth (NOE) flight. Five basic single rotor helicopters - one teetering, two articulated, and two hingeless - which were found to have a variety of major deficiencies in a previous fixed-based simulator study were selected as baseline configurations. The stability and control augmentation systems (SCAS) include simple control augmentation systems (CAS) to decouple pitch and yaw responses due to collective input and to quicken the pitch and roll control responses; SCAS of rate command type designed to optimize the sensitivity and damping and to decouple the pitch-roll due to aircraft angular rate; and attitude command type SCAS. Pilot ratings and commentary are presented as well as performance data related to the task. SCAS control usage and their gain levels associated with specific rotor type are also discussed.

Chen, R. T. N.↗
NASA NTRS1977

A failure effects simulation of a low authority flight control augmentation system on a UH-1H helicopter

A two-pilot moving base simulator experiment was conducted to assess the effects of servo failures of a flight control system on the transient dynamics of a Bell UH-1H helicopter. The flight control hardware considered was part of the V/STOLAND system built with control authorities of from 20-40%. Servo hardover and oscillatory failures were simulated in each control axis. Measurements were made to determine the adequacy of the failure monitoring system time delay and the servo center and lock time constant, the pilot reaction times, and the altitude and attitude excursions of the helicopter at hover and 60 knots. Safe recoveries were made from all failures under VFR conditions. Pilot reaction times were from 0.5 to 0.75 sec. Reduction of monitor delay times below these values resulted in significantly reduced excursion envelopes. A subsequent flight test was conducted on a UH-1H helicopter with the V/STOLAND system installed. Series servo hardovers were introduced in hover and at 60 knots straight and level. Data from these tests are included for comparison.

Corliss, L. D.↗
NASA NTRS1977

A mathematical force and moment model of a UH-1H helicopter for flight dynamics simulations

A model of a UH-1H helicopter was developed to support flight simulations and for developmental work on an avionics system known as V/STOLAND system. Equations and numerical values of constants used to represent the helicopter are presented. Responses to stop inputs of the cyclic and collective controls are shown and compared with flight test data for a UH-1H. The model coefficients were adjusted in an attempt to get a consistant match with the flight time histories at hover and 60 knots. Response matching was obtained at 60 knots, but the matching at hover was not as successful. Pilot evaluations of the model, both fixed and moving base, were made.

Talbot, P. D.↗
NASA NTRS1974

Landing approach evaluation of an integrated CRT display for general aviation aircraft

A flight director adaptable to general aviation aircraft was evaluated for the landing approach task in a twin turbojet business aircraft. The flight director combined aircraft heading, pitch and roll atitude, and ILS (Instrument Landing System) signals into a single picture on a small cathode ray tube (CRT) to give the pilot an integrated picture of the aircraft situation. The display is unique in that it presents the information on a CRT and gives quasi-command signals to the pilot. The particular display investigated was a preproduction version of the Kaiser Model FP-50 flight director. Approaches made with visual references only, with a conventional ILS displacement instrument, and with the CRT display were compared in terms of tracking performance and pilot workload. Tracking performance of three research pilots using the CRT display was superior to that using the conventional ILS instrument and comparable to that under VFR conditions. Pilot workload (based on pilot comments) was not clearly decreased.

Talbot, P. D.↗