Engineering Papers⌕ Search

Engineering topics

Takeuchi, Ichiro

Publications and source records attributed to Takeuchi, Ichiro.

At least 73 records · Page 4

Overcoming fatigue through compression for advanced elastocaloric cooling

Elastocaloric materials exhibit extraordinary cooling potential, but the repetition of cyclic mechanical loadings during long-term operation of cooling systems requires the refrigerant material to have long fatigue life. Here, this paper reviews the fundamental cause of fatigue from aspects of initiation and propagation of fatigue cracks in shape-memory alloys (SMAs) that are used as elastocaloric materials, and highlights recent advances in using compression to overcome fatigue by curtailing the generation of surfaces associated with crack propagation. Compression is identified as a key means to extend fatigue lifetime in engineering design of elastocaloric cooling drive mechanisms. We summarize the state-of-the-art performance of different SMAs as elastocaloric materials and discuss the influence of low cyclic strains and high resistance to transformation. We present integration of compression-based material assemblies into a cooling system prototype and optimization of the system efficiency using work recovery and related measures.

36 MATERIALS SCIENCE↗

Elastocaloric cooling of additive manufactured shape memory alloys with large latent heat

The stress-induced martensitic phase transformation of shape memory alloys (SMAs) is the basis for elastocaloric cooling. In this paper, we employ additive manufacturing to fabricate TiNi SMAs, and demonstrate compressive elastocaloric cooling in the TiNi rods with transformation latent heat as large as 20 J g -1 . Adiabatic compression on as-fabricated TiNi displays cooling ΔT as high as -7.5 °C with recoverable superelastic strain up to 5%. Unlike conventional SMAs, additive manufactured TiNi SMAs exhibit linear superelasticity with narrow hysteresis in stress–strain curves under both adiabatic and isothermal conditions. Microstructurally, we find that there are Ti 2 Ni precipitates typically one micron in size with a large aspect ratio enclosing the TiNi matrix. Finally, a stress transfer mechanism between reversible phase transformation in the TiNi matrix and mechanical deformation in Ti 2 Ni precipitates is believed to be the origin of the unique superelasticity behavior.

36 MATERIALS SCIENCE↗

Fabrication of organic-inorganic perovskite thin films for planar solar cells via pulsed laser deposition

We report on fabrication of organic-inorganic perovskite thin films using a hybrid method consisting of pulsed laser deposition (PLD) of lead iodide and spin-coating of methylammonium iodide. Smooth and highly crystalline CH{sub 3}NH{sub 3}PbI{sub 3} thin films have been fabricated on silicon and glass coated substrates with fluorine doped tin oxide using this PLD-based hybrid method. Planar perovskite solar cells with an inverted structure have been successfully fabricated using the perovskite films. Because of its versatility, the PLD-based hybrid fabrication method not only provides an easy and precise control of the thickness of the perovskite thin films, but also offers a straightforward platform for studying the potential feasibility in using other metal halides and organic salts for formation of the organic-inorganic perovskite structure.

36 MATERIALS SCIENCE↗

Ultrafast terahertz gating of the polarization and giant nonlinear optical response in BiFeO 3 thin films

In this article, terahertz pulses are applied as an all-optical bias to ferroelectric thin-film BiFeO 3 while monitoring the time-dependent ferroelectric polarization through its nonlinear optical response. Modulations in the intensity of the second harmonic light generated by the film correspond to on–off ratios of 220 × gateable on femtosecond timescales. Polarization modulations comparable to the built-in static polarization are observed.

36 MATERIALS SCIENCE↗

Robust topological surface state in Kondo insulator SmB{sub 6} thin films

Fabrication of smooth thin films of topological insulators with true insulating bulk are extremely important for utilizing their novel properties in quantum and spintronic devices. Here, we report the growth of crystalline thin films of SmB{sub 6}, a topological Kondo insulator with true insulating bulk, by co-sputtering both SmB{sub 6} and B targets. X-ray diffraction, Raman spectroscopy, and transmission electron microscopy indicate films that are polycrystalline with a (001) preferred orientation. When cooling down, resistivity ρ shows an increase around 50 K and saturation below 10 K, consistent with the opening of the hybridization gap and surface dominated transport, respectively. The ratio ρ{sub 2K}/ρ{sub 300K} is only about two, much smaller than that of bulk, which indicates a much larger surface-to-bulk ratio. Point contact spectroscopy using a superconductor tip on SmB{sub 6} films shows both a Kondo Fano resonance and Andeev reflection, indicating an insulating Kondo lattice with metallic surface states.

36 MATERIALS SCIENCE↗

Change in the magnetic structure of (Bi,Sm)FeO{sub 3} thin films at the morphotropic phase boundary probed by neutron diffraction

We report on the evolution of the magnetic structure of BiFeO{sub 3} thin films grown on SrTiO{sub 3} substrates as a function of Sm doping. We determined the magnetic structure using neutron diffraction. We found that as Sm increases, the magnetic structure evolves from a cycloid to a G-type antiferromagnet at the morphotropic phase boundary, where there is a large piezoelectric response due to an electric-field induced structural transition. The occurrence of the magnetic structural transition at the morphotropic phase boundary offers another route towards room temperature multiferroic devices.

36 MATERIALS SCIENCE↗

On-the-fly machine-learning for high-throughput experiments: search for rare-earth-free permanent magnets

Advanced materials characterization techniques with ever-growing data acquisition speed and storage capabilities represent a challenge in modern materials science, and new procedures to quickly assess and analyze the data are needed. Machine learning approaches are effective in reducing the complexity of data and rapidly homing in on the underlying trend in multi-dimensional data. Here, we show that by employing an algorithm called the mean shift theory to a large amount of diffraction data in high-throughput experimentation, one can streamline the process of delineating the structural evolution across compositional variations mapped on combinatorial libraries with minimal computational cost. Data collected at a synchrotron beamline are analyzed on the fly, and by integrating experimental data with the inorganic crystal structure database (ICSD), we can substantially enhance the accuracy in classifying the structural phases across ternary phase spaces. We have used this approach to identify a novel magnetic phase with enhanced magnetic anisotropy which is a candidate for rare-earth free permanent magnet.

Kusne, AG↗