Engineering topics
Takeuchi, Esther S.
Publications and source records attributed to Takeuchi, Esther S..
Impact of sodium vanadium oxide (NaV 3 O 8 , NVO) material synthesis conditions on charge storage mechanism in Zn-ion aqueous batteries
The electrochemical charge storage of sodium vanadate (NaV 3 O 8 or NVO) cathodes in aqueous Zn-ion batteries has been hypothesized to be influenced by the inclusion of structural water for facilitating ion transfer in the material. Materials properties considered important (morphology, crystallite and particle size, surface area) are systematically studied herein through investigation of two NVO materials, NaV 3 O 8 ·0.34H 2 O [NVO(300)] and NaV 3 O 8 ·0.05H 2 O [NVO(500)], with different water content, acicular morphologies with different size and surface area achieved via post-synthesis heat treatment. The electrochemistry of the two materials was evaluated in aqueous Zn-ion cells with 2 M ZnSO 4 electrolyte using cyclic voltammetry, galvanostatic cycling, and rate capability testing. Furthermore, the thinner NVO(300) nanobelts (0.13 μm) demonstrate greater specific capacities and higher effective diffusion coefficients relative to the thicker NVO(500) nanorods. Notably however, while cells containing NVO(500) deliver lower specific capacity, they demonstrate enhanced capacity retention with cycling. The structural changes accompanying oxidation and reduction are elucidated via ex situ X-ray diffraction, transmission electron microscopy, and operando V K-edge X-ray absorption spectroscopy (XAS), where NVO material properties are shown to influence the ion insertion. Operando XAS verified that electron transfer corresponds directly to change in vanadium oxidation state, affirming vanadium redox as the governing electrochemical process.
Achieving Stable Molybdenum Oxide Cathodes for Aqueous Zinc‐Ion Batteries in Water‐in‐Salt Electrolyte
Abstract Layered MoO 3 represents a promising cathode for aqueous rechargeable Zn‐ion batteries, but the implementation of this material is limited due to the low conductivity and poor structural stability. A 30 m ZnCl 2 water‐in‐salt electrolyte (WISE) is introduced to a MoO 3 nanobelt cathode for the first time, significantly increasing the stability of MoO 3 cathodes compared to those in 3 m ZnSO 4 and 3 m ZnCl 2 . The Zn/MoO 3 cell in WISE unambiguously demonstrate significantly improved rate performance delivering 349, 253, and 222 mAh g −1 at 100, 500, and 1000 mA g −1 , denoting a 12× capacity increase of those achieved in 3 m electrolytes at 1000 mA g −1 . A capacity retention rate of 73% is achieved after (dis)charging at 100 mA g −1 for 100 cycles, and no obvious capacity fading is observed at higher current densities of 500 mA g −1 and 2 A g −1 . Specifically, the data suggest that the drastic fading in 3 m electrolytes can be attributed to the parasitic surface deposits on Zn originated from Mo dissolution and H 2 formation due to Zn corrosion and hydrogen evolution reaction, which are significantly suppressed in the WISE. The direct visualization of these side reactions is achieved for the first time in the Zn‐MoO 3 system, using an in situ optoelectrochemical measurement.
Self-Healing, Improved Efficiency Solid State Rechargeable Li/I 2 Based Battery
Solid state electrolytes are receiving significant interest due to the prospect of improved safety, however, addressing the incidence and consequence of internal short circuits remains an important issue. In this study, a battery based on a LiI-LiI(HPN) 2 solid state electrolyte demonstrated self-healing after internal shorting where the cells recovered and continued to cycle effectively. The functional rechargeable electrochemistry of the self-forming Li/I 2 -based battery was investigated through interfacial modification by inclusion of Li metal (at the negative interface), and/or fabricated carbon nanotube substrates at the positive interface. A cell design with lithium metal at the negative and a carbon substrate at the positive interface produced Coulombic efficiencies > 90% over 60 cycles. Finally, the beneficial effects of moderately elevated temperature were established where a 10 °C temperature increase led to ~5× lower resistance.
Peering into Batteries: Electrochemical Insight Through In Situ and Operando Methods over Multiple Length Scales
Not Available
New Insights into the Reaction Mechanism of Sodium Vanadate for an Aqueous Zn Ion Battery
Explore the source record for details and available documents.
Understanding Thickness-Dependent Transport Kinetics in Nanosheet-Based Battery Electrodes
Explore the source record for details and available documents.
Nickel-rich Nickel Manganese Cobalt (NMC622) Cathode Lithiation Mechanism and Extended Cycling Effects Using Operando X-ray Absorption Spectroscopy
Ni-rich NMC materials are a particularly promising class of Li-ion cathodes for various applications. LiNi 0.6 Mn 0.2 Co 0.2 O 2 (NMC622) offers a unique balance of thermal stability and energy density, thus attracting attention for electric vehicle implementation. However, upon extended cycling, capacity fade is prevalent due to structural degradation, which is a major drawback for layered oxide cathodes. Therefore, exploring the underlying phenomena that drive detrimental structural response can lead to future improvements. For the first time, operando X-ray absorption spectroscopy (XAS) was performed on NMC622 pouch cells at three different stages. An extensive description of the first cycle (de)lithiation mechanisms was achieved through X-ray absorption near-edge structure analyses and extended X-ray absorption fine structure modeling. Transition metal specific electrochemical participation and structural variation revealed that much of the delivered capacity and distortion is a result of Ni redox behavior, while the local structure of Co and Mn are impacted due to their interdependencies. Key mechanistic components were identified, as the local structural variation from redox processes and Ni 3+ Jahn–Teller distortion were decoupled. Further, operando XAS was used to investigate the structural response of NMC622 to extended cycling and was supported by X-ray diffraction, X-ray photoelectron spectroscopy, and electrochemical impedance spectroscopy analyses. In this work, reduced capacity was found in the cell after 100 cycles and is attributed to structural degradation and cathode–electrolyte interphase buildup from repeated Li (de)insertion processes, which limit the electrochemical reversibility of Ni and Co through increased polarization. These results expand the understanding of a Ni-rich NMC material under extended cycling, which is vital to the future design of electrode materials.
Improved Capacity Retention of Lithium Ion Batteries under Fast Charge via Metal-Coated Graphite Electrodes
A primary barrier preventing repetitive fast charging of Li-ion batteries is lithium metal plating at the graphite anode. One approach toward mitigating Li metal deposition is the deliberate modification of the graphite anode surface with materials demonstrating high overpotentials unfavorable for Li metal nucleation, such as Ni or Cu nanoscale films. This research explores Ni and Cu surface coatings at different areal loadings (3 or 11 μg cm -2 ) on the electrochemistry of graphite/LiNi 0.6 Mn 0.2 Co 0.2 O 2 (NMC622) type Li-ion batteries. Extended galvanostatic cycling of control and metal-coated electrodes in graphite/NMC622 pouch cells are conducted under high rate conditions. Based on the overpotential of Li deposition on metal foil, both Ni and Cu treatments were anticipated to result in reduced lithium deposition. The higher metal film loadings of 11 μg cm -2 Ni- or Cu-coated electrodes exhibit the highest capacity retention after 500 cycles, with mean improvements of 8% and 9%, respectively, over uncoated graphite electrodes. Li plating quantified by X-ray diffraction indicates that the metal films effectively reduce the quantity of plated Li compared to untreated electrodes, with 11 μg cm -2 Cu providing the greatest benefit.
Unraveling the Dissolution-Mediated Reaction Mechanism of α-MnO 2 Cathodes for Aqueous Zn-Ion Batteries
Aqueous Zn/α-MnO 2 batteries have attracted immense interest owing to their high energy density, low cost, and safety, making them desirable for future large-scale energy application. Despite these merits, the comprehensive understanding of their reaction mechanism has been elusive due to the limitations of standard bulk characterization. Here, via transmission electron microscopy, the dissolution-mediated reaction mechanism of a Zn/α-MnO 2 system is discovered and explored in full scope to involve reversible formation of Zn 4 SO 4 (OH) 6 · x H 2 O and “birnessite-like” Zn-MnO x phase upon cycling. Overall, α-MnO 2 acts primarily as a source for cell activation through dissolution and thus is not directly involved in the Zn redox chemistry. Overall, this microscopic study offers a unique knowledge on the unconventional reaction chemistry of Zn/α-MnO 2 batteries.
Microwave-Based Synthesis of Functional Morphological Variants and Carbon Nanotube-Based Composites of VS 4 for Electrochemical Applications
A novel facile, fast, and efficient microwave-assisted method was developed to synthesize a number of diverse nanostructured motifs (ranging from nanorods to nanoflowers) of VS 4 along with its associated composite heterostructures, VS 4 /multi-walled carbon nanotube (MWNT; i.e., multi-walled carbon nanotubes). Specifically, we have probed and correlated the effects of a number of specific experimental variables, including primarily precursor, solvent, temperature, and time. We noted that nanorods formed more readily with VO(acac) 2 as the vanadium precursor and n-methyl-2-pyrrolidone (NMP) as a polar reaction solvent. By contrast, we determined that hierarchical three-dimensional (3D) nanoflower-like assemblies, ranging in size from 100 to 200 nm in average diameter, could be controllably synthesized by using Na 3 VO 4 as the vanadium precursor and an aqueous water: polar solvent mixture as the reaction medium. We also observed that VS 4 disintegrates, when in the presence of either air, solution, or a combination of these environments, and established that the extent of VS4 nanorod decomposition could be almost fully prevented by storage under nitrogen. From an application’s perspective, our VS 4 is electrochemically active and shows behavior, consistent with the literature. In particular, as compared with pristine VS 4 nanorods alone, we observed enhanced electrochemical activity with (i) 3D hierarchical flower-like motifs, (ii) unique necklace-like VS 4 nanorod–MWNT composites, and (iii) samples in which as-prepared VS4 nanorods had been annealed. Moreover, we found that the rational application of specific physical and chemical processing treatments, such as (i) thermal annealing to improve crystallinity, (ii) the addition of MWNTs to form conductive composites, and (iii) the evolution of morphology from one-dimensional (1D) nanorods to more complex 3D nanoflowers, was favorable to the resulting electrochemical performance with respect to increasing stability and reversibility.
Quantitative temporally and spatially resolved X-ray fluorescence microprobe characterization of the manganese dissolution-deposition mechanism in aqueous Zn/α-MnO 2 batteries
Rechargeable aqueous Zn/α-MnO 2 batteries are a possible alternative to lithium ion batteries for scalable stationary energy storage applications due to their low cost, safety and environmentally benign components. A critical need for advancement of this battery system is a full understanding of the electrochemical reaction mechanisms, which remain unclear. In this report, operando , spatiotemporal resolved synchrotron X-ray fluorescence mapping measurements on a custom aqueous Zn/α-MnO 2 cell provided direct evidence of a Mn dissolution-deposition faradaic mechanism that governs the electrochemistry. Simultaneous visualization and quantification of the Mn distribution in the electrolyte revealed the formation of aqueous Mn species during discharge and depletion on charge. The findings are supported by ex situ transmission electron microscopy (TEM), X-ray diffraction, Mn K-edge X-ray absorption near edge structure (XANES) and extended X-ray absorption fine structure (EXAFS) measurements. The elucidated mechanism is fundamentally different from the previously proposed Zn 2+ insertion or conversion reactions. These findings provide a foundation for developing dissolution- deposition chemistries suitable for scalable stationary energy storage with aqueous electrolyte.
Low-temperature synthesis process of making MgzMxOy, where M is Mn, V or Fe, for manufacture of electrode materials for group II cation-based batteries
Preparation, characterization, and an electrochemical study of Mg 0.1 V 2 O 5 prepared by a novel sol-gel method with no high-temperature post-processing are disclosed. Cyclic voltammetry showed the material to be quasi-reversible, with improved kinetics in an acetonitrile-, relative to a carbonate-, based electrolyte. Galvanostatic test data under a C/10 discharge showed a delivered capacity >250 mAh/g over several cycles. Based on these results, a magnesium anode battery, as disclosed, would yield an average operating voltage ˜3.2 Volts with an energy density ˜800 mWh/g for the cathode material, making the newly synthesized material a viable cathode material for secondary magnesium batteries.
The effect of chemically preintercalated alkali ions on the structure of layered titanates and their electrochemistry in aqueous energy storage systems
We introduce a novel chemical preintercalation synthesis technique based on a hydrogen peroxide induced sol–gel process to obtain alkali ion containing ternary layered titanates (MTO, where M = Li, Na, K). Synthesis parameters leading to the formation of single-phase materials with homogeneous elemental distribution are reported for each of the preintercalated ions. Our analyses indicate that the interlayer spacing in the structure of the layered titanates increases with the increase of the radius of the hydrated preintercalated ion. Scanning and transmission electron microscopy imaging revealed morphological diversity: the LTO phase crystallized as nanoplates assembled in “peony-like” spherical agglomerates while NTO and KTO particles exhibited a one-dimensional nanobelt or wire-like morphology, with the KTO nanobelts being shorter and more aggregated than the NTO nanobelts. Structural refinement corroborated by electron diffraction and high-resolution transmission electron microscopy revealed that the structure of the LTO phase is built by stacking Ti–O layers containing a single straight layer of connected TiO 6 octahedra. The layers in NTO and KTO structures form differently and consist of double Ti–O layers with two titanium rows and ragged arrangement of units built by TiO6 octahedra. The NTO electrodes exhibited the highest electrochemical performance in cells with aqueous 1 M Na 2 SO 4 electrolyte, followed by the KTO electrodes and then LTO electrodes, and this trend is maintained at various scan rates. The established relationships between the structure and electrochemical performance reveal that, in addition to interlayer distance and chemistry of the interlayer region, the structure of the layers can play an important role in charge storage properties of layered oxide electrodes. The double Ti–O layers in the structure of NTO and KTO phases provide a larger number of redox centers which could contribute to the superior electrochemical performance as compared to the LTO electrodes. Our findings indicate that layered materials containing double transition metal oxide layers are promising candidates for exfoliation and assembly with electronically conductive layers with the aim to create 2D heterostructures with high electrochemical performance.
Magnesium Todorokite: Influence of Morphology on Electrochemistry in Lithium, Sodium and Magnesium Based Batteries
Samples of Mg-todorokite with mixed nanosheet & nanowire (referred to as nanosheets for the sake of simplicity) and pure nanowire morphology were prepared to probe the morphological impact on battery relevant electrochemistry. The samples had similar physicochemical properties where the Mg-todorokite nanosheets had a composition of Mg 0.20 MnO 2 with a crystallite size of 9 nm and water content of 0.29 moles of H 2 O per formula unit, while the nanowires had a composition of Mg 0.19 MnO 2 with a crystallite size of 14 nm and water content of 0.28. The electrochemistry of the Mg-todorokite materials was evaluated using cyclic voltammetry, galvanostatic cycling, and rate capability testing. The Mg-todorokite nanosheets showed higher discharge capacity than the nanowires in lithium, sodium and magnesium-based electrolytes. Notably, the nanowire materials exhibited excellent cycling stability compared to the nanosheets in lithium and sodium-based batteries. Finally, x-ray absorption spectroscopy (XAS) of lithiated samples suggests that Mn in the nanosheet containing material was more highly reduced to Mn 3+ after the 1st full discharge explaining the higher initial capacities observed. However, a MnO-like structural distortion was observed after extended cycling in the nanosheet material consistent with its poorer capacity retention.
Solution-Based, Anion-Doping of Li 4 Ti 5 O 12 Nanoflowers for Lithium-Ion Battery Applications
Solution–based, anionic doping represents a convenient strategy with which to improve upon the conductivity of candidate anode materials such as Li 4 Ti 5 O 12 (LTO). As such, novel synthetic hydrothermally–inspired protocols have primarily been devised herein, aimed at the large–scale production of unique halogen–doped, micron–scale, three–dimensional, hierarchical LTO flower–like motifs. Although fluorine (F) doping has been explored, the use of chlorine (Cl) dopants is the primary focus here. Several experimental variables, such as dopant amount, lithium hydroxide concentration, and titanium butoxide purity, were probed and perfected. Furthermore, the Cl doping process did not damage the intrinsic LTO morphology. The analysis, based on interpreting a compilation of SEM, XRD, XPS, and TEM–EDS results, was used to determine an optimized dopant concentration of Cl. Electrochemical tests demonstrated an increased capacity via cycling of 12 % for a Cl–doped sample as compared with pristine LTO. Moreover, the Cl–doped LTO sample described in this study exhibited the highest discharge capacity yet reported at an observed rate of 2C for this material at 143mAh g –1 . Overall, these data suggest that the Cl dopant likely enhances not only the ion transport capabilities, but also the overall electrical conductivity of our as–prepared structures. Furthermore, to help explain these favorable findings, theoretical DFT calculations were used to postulate that the electronic conductivity and Li diffusion were likely improved by the presence of increased Ti 3+ ion concentration coupled with widening of the Li migration channel.
Spontaneous and field-induced crystallographic reorientation of metal electrodeposits at battery anodes
The propensity of metal anodes of contemporary interest (e.g., Li, Al, Na, and Zn) to form non-planar, dendritic morphologies during battery charging is a fundamental barrier to achievement of full reversibility. We experimentally investigate the origins of dendritic electrodeposition of Zn, Cu, and Li in a three-electrode electrochemical cell bounded at one end by a rotating disc electrode. We find that the classical picture of ion depletion–induced growth of dendrites is valid in dilute electrolytes but is essentially irrelevant in the concentrated (≥1 M) electrolytes typically used in rechargeable batteries. Using Zn as an example, we find that ion depletion at the mass transport limit may be overcome by spontaneous reorientation of Zn crystallites from orientations parallel to the electrode surface to dominantly homeotropic orientations, which appear to facilitate contact with cations outside the depletion layer. This chemotaxis-like process causes obvious texturing and increases the porosity of metal electrodeposits.
Water-induced formation of an alkali-ion dimer in cryptomelane nanorods
Water displaces potassium ions and initiates the formation of a homonuclear dimer ion (K 2+ ) in the tunnels of hollandite.