Engineering Papers⌕ Search

Engineering topics

Takeuchi, Esther S.

Publications and source records attributed to Takeuchi, Esther S..

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Origin of Phase Separation in Ni-Rich Layered Oxide Cathode Materials During Electrochemical Cycling

In intercalation materials, the kinetics and uniformity of mass transport across the nanocrystalline domains dictate the structural reversibility and transport capability at the macroscopic level. (De)intercalation-induced interlayer disintegrations exhibit anisotropic crystallite size change. Due to the anisotropic mass transport mechanism, separated phases are inherently crystallographically oriented. One such material is LiNi $1–x–y$ Mn $x$ Co $y$ O 2 , which plays a pivotal role in advanced Li-ion batteries but suffers from severe phase inhomogeneities under fast charge or electrochemical aging. Here, using operando synchrotron techniques, we probe the mechanistic origins of the compositional and orientational-dependent phase separations during the electrochemical cycling of LiNi 0.8 Mn 0.1 Co 0.1 O 2 by comprehensive analysis of both in-plane and out-of-plane reflections. In the H2/H3 phase regime, in-plane domain propagation occurs due to increased covalency despite the severe decay of interlayer crystallographic order, resulting in the change of crystalline domain shape from 3D spheres to two-dimensional nanosheets. The crystallographically selective XRD line splitting is linked to the geometry of the facets as mass transfers along the ab plane. In conclusion, this work provides mechanistic insights into crystallographic orientation-dependent phase inhomogeneity under fast charge and extended cycling.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Mechanism of Chalcophanite Nucleation in Zinc Hydroxide Sulfate Cathodes in Aqueous Zinc Batteries

Aqueous Zn-ion batteries with MnO 2 -based cathodes have seen significant attention owing to their high theoretical capacities, safety, and low cost; however, much debate remains regarding the reaction mechanism that dominates energy storage. In this work, we report our electron microscopy study of cathodes containing zinc hydroxide sulfate (Zn 4 SO 4 (OH) 6 ·xH 2 O, ZHS) together with carbon nanotubes cycled in electrolytes containing ZnSO 4 with varied amounts of MnSO 4 incorporated. The primary Mn-containing phase is formed in situ in the cathode during cycling, where a dissolution-deposition reaction is identified between ZHS and chalcophanite (ZnMn 3 O 7 ·3H 2 O). Mechanistic details of this reaction, in which the chalcophanite nucleates then separates from the ZHS flakes as the ZHS dissolves while acting as the primary Zn source for the reaction, are revealed using surface sensitive methods. Importantly, these findings indicate the reaction is local to the ZHS flakes, providing new insight toward the importance of ZHS and the cathode microstructure.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2023

Improving charge transport in integrated MoO 3 /C electrode materials for water-in-salt energy storage systems by incorporating oxygen vacancies

Improvements in the charge storage properties of α-MoO 3 used as an electrode with a 30m ZnCl 2 water-in-salt electrolyte have been achieved by enhancements in electron and ion transport enabled by an inventive synthesis route. Electron transport was improved through the integration of MoO 3 with dopamine-derived carbon via a chemical preintercalation route, and enhanced ion transport was achieved by incorporating oxygen vacancies in MoO 3 structure through ethanol 2 reduction under hydrothermal conditions. Here, the presence of carbon was confirmed by corresponding D and G bands observed in Raman spectroscopy measurements. The presence of oxygen vacancies was proven through correlated XPS, TGA, Raman spectroscopy and XRD analyses, with the introduction of oxygen vacancies leading to an expanded interlayer region. Four-point probe measurements provided evidence of increased electronic conductivity due to the incorporation of carbon, and cyclic voltammetry-based charge storage mechanism analyses revealed increases in ion transport kinetics due to oxygen vacancy formation. Tuning the oxygen vacancy concentration is critical, as excessive concentrations of these point defects leads to structural instability and poor capacity retention. This work demonstrates the combined potential of carbon and oxygen vacancies in moderate concentrations to enhance the charge storage properties of transition metal oxides. The strategies developed in this study offer a path to the development of promising materials for high-rate, high-capacity, and long-duration electrochemical energy storage technologies.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2023

The Relationship between Ionic Conductivity and Solvation Structures of Localized High-Concentration Fluorinated Electrolytes for Lithium-Ion Batteries

Localized high concentration electrolyte (LHCE) combines a diluent with high concentration electrolyte (HCE), offering promising properties. The ions, solvent, and diluent interact to form a complex heterogenous liquid structure, where high salt concentration clusters are embedded in diluent. Optimizing LHCE for desired electrolyte properties like high ionic conductivity, low viscosity, effective solid electrolyte interphase (SEI) formability, within the vast chemical and compositional design space requires deeper understanding and theoretical guidance. For this work, we investigated the structures and conductivity of LHCEs based on a fluorinated solvent with two different diluents at varying concentrations. The 2,2,3,3-tetrafluoropropyl trifluoroacetate (TFPTFA) enters the solvation cluster due to its stronger Li-ion interactions, whereas 1,1,2,2-tetrafuoroethyl 2,2,2-trifuoroethyl ether (TFETFE) enters only at extremely high diluent concentrations. The ionic conductivity increases with decreasing diluent concentrations, with a slope change during cluster percolation. Overall, TFETFE demonstrates higher effectiveness than TFPTFA, forming higher local salt concentration clusters, and resulting in higher ionic conductivity.

cluster chemistry↗
DOE OSTI2023

Densified vertically lamellar electrode architectures for compact energy storage

As one of the most compact electrochemical energy storage systems, lithium-ion batteries (LIBs) are playing an indispensable role in the process of vehicle electrification to accelerate the shift to sustainable mobility. Making battery electrodes thicker is a promising strategy for improving the energy density of LIBs which is essential for applications with weight or volume constraints, such as electric-powered transportation; however, their power densities are often significantly restricted due to elongated and tortuous charge traveling distances. Here, we propose an effective methodology that couples bidirectional freeze-casting and compression-induced densification to create densified vertically lamellar electrode architectures for compact energy storage. The vertically lamellar architectures not only overcome the critical thickness limit for conventional electrodes but also facilitate and redistribute the lithium-ion flux enabling both high rate capability and stable cyclability. Furthermore, this proposed methodology is universal as demonstrated in various electrochemical active material systems. This study offers a facile approach that realizes simultaneous high energy and high power in high-loading battery electrodes and provides useful rationales in designing electrode architectures for scalable energy storage systems.

42 ENGINEERING↗
DOE OSTI2023

Understanding the reversible electrodeposition of aluminum in low-cost room-temperature molten salts

Aluminum is the most earth-abundant metal, trivalent, and inert in ambient air; it also has a density approximately five times that of lithium at room temperature, making it attractive for cost-effective, long-duration storage in batteries. Here, we investigate structural requirements and physicochemical and transport properties of ionic liquid (IL) electrolytes thought to enable high reversibility of Al battery anodes. We find that intentionally designed, low-cost IL analogs, including ammonium-based molten salts, offer comparable Al anode reversibility to state-of-the-art imidazolium-based IL melts. A critical ratio of solvated Al-ion species is required to balance the effects of Lewis acidity needed to continuously etch native Al 2 O 3 and form a stable solid electrolyte interphase on Al. Our findings open new opportunities for developing simple, cost-effective, room-temperature Al batteries that enable long-duration electrical energy storage.

25 ENERGY STORAGE↗
DOE OSTI2023

Isothermal Microcalorimetric Analysis of Li/CF x Battery Discharge

Lithium/carbon monofluoride (Li/CF x ) batteries generate substantial amounts of heat during discharge in part due to the large deviation of the loaded voltage from the measured and thermodynamically predicted open circuit voltage. Here, in this study, we further analyze this system by estimating the equilibrium voltage (V eq ) and its temperature dependence (dV eq /dT) over the entire discharge range. Based on these results, the ohmic and entropic heat contributions to the overall heat flow are calculated from experimental data. The ohmic heat flow is consistent with an electrochemical impedance spectroscopy model and electrode density measurements, indicating decreasing porosity of the electrode during discharge. Entropic heating increases during discharge as the cell reaction becomes increasingly entropically unfavorable. The total energy dissipated by the cell (electrical and thermal) remains similar over the entire discharge, evidence for a two-phase reaction with a constant, and rate-independent, ΔG rxn of about -465 kJ mol -1 . However, near the end of discharge (>90% DOD), ΔG rxn changes significantly indicating possible secondary reactions.

25 ENERGY STORAGE↗
DOE OSTI2023

Two-Dimensional Siloxene Nanosheets: Impact of Morphology and Purity on Electrochemistry

Two-dimensional (2D) siloxene (Si 6 O 3 H 6 ) has shown promise as a negative electrode material for Li-ion batteries due to its high gravimetric capacity and superior mechanical properties under (de)lithiation compared to bulk Si. Here, in this work, we prepare purified siloxene nanosheets through the removal of bulk Si contaminants, use ultrasonication to control the lateral size and thickness of the nanosheets, and probe the effects of the resulting morphology and purity on the electrochemistry. The thin siloxene nanosheets formed after 4 h of ultrasonication deliver an average capacity of 810 mA h/g under a 1000 mA/g rate over 200 cycles with a capacity retention of 76%. Interestingly, the purified siloxene shows lower initial capacity but superior capacity retention over extended cycling. The 2D morphology benefit is illustrated where the parent siloxene nanosheet morphology and structure were largely maintained based on operando optoelectrochemistry, in situ Raman, ex situ scanning electron microscopy, and ex situ transmission electron microscopy. Furthermore, the purified siloxene-based electrode free from crystalline Si impurity experiences the least expansion upon (de)lithiation as visualized by cross-section electron microscopy of samples recovered post-cycling.

25 ENERGY STORAGE↗
DOE OSTI2023

Microwave-Assisted Fabrication of High Energy Density Binary Metal Sulfides for Enhanced Performance in Battery Applications

Nanomaterials have found use in a number of relevant energy applications. In particular, nanoscale motifs of binary metal sulfides can function as conversion materials, similar to that of analogous metal oxides, nitrides, or phosphides, and are characterized by their high theoretical capacity and correspondingly low cost. This review focuses on structure–composition–property relationships of specific relevance to battery applications, emanating from systematic attempts to either (1) vary and alter the dimension of nanoscale architectures or (2) introduce conductive carbon-based entities, such as carbon nanotubes and graphene-derived species. In this study, we will primarily concern ourselves with probing metal sulfide nanostructures generated by a microwave-mediated synthetic approach, which we have explored extensively in recent years. This particular fabrication protocol represents a relatively facile, flexible, and effective means with which to simultaneously control both chemical composition and physical morphology within these systems to tailor them for energy storage applications.

25 ENERGY STORAGE↗
DOE OSTI2023

Elucidating a dissolution–deposition reaction mechanism by multimodal synchrotron X-ray characterization in aqueous Zn/MnO 2 batteries

Aqueous Zn/MnO 2 batteries with their environmental sustainability and competitive cost, are becoming a promising, safe alternative for grid-scale electrochemical energy storage. Here, presented as a promising design principle to deliver a higher theoretical capacity, this work offers fundamental understanding of the dissolution–deposition mechanism of Zn/β-MnO 2 . A multimodal synchrotron characterization approach including three operando X-ray techniques (powder diffraction, absorption spectroscopy, and fluorescence microscopy) is coupled with elementally resolved synchrotron X-ray nano-tomography. Together they provide a direct correlation between structural evolution, reaction chemistry, and 3D morphological changes. Operando synchrotron X-ray diffraction and spectroscopy show a crystalline-to-amorphous phase transition. Quantitative modeling of the operando data by Rietveld refinement for X-ray diffraction and multivariate curve resolution (MCR) for X-ray absorption spectroscopy are used in a complementary fashion to track the structural and chemical transitions of both the long-range (crystalline phases) and short-range (including amorphous phases) ordering upon cycling. Scanning X-ray microscopy and full-field nano-tomography visualizes the morphology of electrodes at different electrochemical states with elemental sensitivity to spatially resolve the formation of the Zn- and Mn-containing phases. Overall, this work critically indicates that for Zn/MnO 2 aqueous batteries, the reaction pathways involving Zn–Mn complex formation upon cycling become independent of the polymorphs of the initial electrode and sheds light on the interplay among structural, chemical, and morphological evolution for electrochemically driven phase transitions.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Degradation in Ni-Rich LiNi 1– x – y Mn x Co y O 2 /Graphite Batteries: Impact of Charge Voltage and Ni Content

Ni-rich LiNi 1– x–y Mn x CoyO 2 (NMC) materials are attractive as cathodes for Li-ion batteries due to their high energy density and low Co content. However, these materials may display poor electrochemical reversibility relating to structural and interfacial instabilities. The influence of Ni content and level of delithiation during charge on degradation mechanisms and relevance to electrochemical cycling behavior are probed for LiNi 0.6 Mn 0.2 Co 0.2 O 2 (NMC622) and LiNi 0.8 Mn 0.1 Co 0.1 O 2 (NMC811) cathode materials in a full cell configuration under two upper voltage limits (4.1 and 4.3 V). The combined use of dQ/dV analysis of electrochemical voltage profiles, operando XRD, and postcycling scanning electron microscopy (SEM) measurements indicates that a major contributor to capacity fade is the large anisotropic volume change from an H2 $\leftrightarrows$ H3 phase transition and associated mechanical degradation particularly for NMC811. Notably, transition metal dissolution and deposition on the negative electrode are found to correlate with the structural changes occurring in the cathode under high voltage charge. X-ray photoelectron spectroscopy (XPS) analyses of the cycled cathodes reveal a more organic-rich cathode–electrolyte interphase (CEI) when cycling to 4.3 V with lower relative amounts of LiF. Surface reconstruction is not a significant factor under these cycling conditions as determined by soft X-ray absorption spectroscopy (sXAS) analysis. The results emphasize the opportunity to match the electrochemical test parameters with the specific NMC active material to mitigate degradation and extend cycle life.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Tuning Discharge Behavior of Hollandite α-MnO 2 in Hydrated Zinc Ion Battery by Transition Metal Substitution

The tunnel-type hollandite α-MnO 2 is a promising cathode material for rechargeable aqueous zinc-ion batteries (ZIBs) due to its low cost in synthesis and high energy density. However, irreversible structural degradation upon continuous cycling prevents the cathode from being utilized commercially. Herein, density functional theory (DFT) was utilized to conduct a systematic study on tuning the behavior of α-MnO 2 by substituting the Mn ions on the tunnel wall with a transition metal (V or Cr) during the H + -/Zn 2+ -intercalation in hydrated ZIB. Our study revealed that both substituents aid cyclability and capacity retention with Cr outperforming V. In term of discharge voltage, only the Cr-substitution displays clear promotion at the early stage of discharge. The superior performance of substituted Cr 4+ comes from its unique atomic and electronic structures. Upon discharge, it can be reduced to Cr 3+ more readily than Mn 4+ and thereby limits the formation of unstable Mn 3+ or Mn 2+ centers; the formed Cr 3+ is more stable than Mn 3+ and Mn 2+ from the reduction of Mn 4+ ; and Cr 3+ can also greatly stabilize the neighboring Mn ions. Here this study highlights the significant tuning effect of transition metal substitution on the electrochemical and physical performance of α-MnO 2 as a cathode in hydrated ZIBs.

25 ENERGY STORAGE↗