Engineering topics

Tadas Bartkus

Publications and source records attributed to Tadas Bartkus.

7 records

NASA NTRS2017

An Initial Study of the Fundamentals of Ice Crystal Icing Physics in the NASA Propulsion Systems Laboratory

This presentation shows results from an initial study of the fundamental physics of ice-crystal ice accretion using the NASA Propulsion Systems Lab (PSL). Ice accretion due to the ingestion of ice-crystals is being attributed to numerous jet-engine power-loss events. The NASA PSL is an altitude jet-engine test facility which has recently added a capability to inject ice particles into the flow. NASA is evaluating whether this facility, in addition to full-engine and motor-driven-rig tests, can be used for more fundamental ice-accretion studies that simulate the different mixed-phase icing conditions along the core flow passage of a turbo-fan engine compressor. The data from such fundamental accretion tests will be used to help develop and validate models of the accretion process. The present study utilized a NACA0012 airfoil. The mixed-phase conditions were generated by partially freezing the liquid-water droplets ejected from the spray bars. This presentation shows data regarding (1) the freeze out characteristics of the cloud, (2) changes in aerothermal conditions due to the presence of the cloud, and (3) the ice accretion characteristics observed on the airfoil model. The primary variable in this test was the PSL plenum humidity which was systematically varied for two duct-exit-plane velocities (85 and 135 ms) as well as two particle size clouds (15 and 50 m MVDi). The observed clouds ranged from fully glaciated to fully liquid, where the liquid clouds were at least partially supercooled. The air total temperature decreased at the test section when the cloud was activated due to evaporation. The ice accretions observed ranged from sharp arrow-like accretions, characteristic of ice-crystal erosion, to cases with double-horn shapes, characteristic of supercooled water accretions.

upwind schemes↗

NASA NTRSDate not supplied

Cloud Uniformity Measurement from NASA's 2nd Fundamental Ice Crystal Icing Test - Part 2 (Temperature and Humidity)

This paper provides a characterization of the temperature and humidity variations within icing cloud flows generated during the second Fundamental Ice Crystal Icing Physics test conducted in NASA’s Propulsion Systems Laboratory, in June of 2018. The tests were conducted at airflow velocities of 85, 135, and 185 m/s, a static pressure of 44.8 kPa, and a total temperature of 7.2 ⁰C. A custom rearward facing probe and commercial total air temperature probe were used to obtain temperature and humidity profiles of the icing cloud flow leaving the exit duct plane. Additional background humidity measurements were also obtained from a commercial total water content probe. The probes captured the changes in temperature and humidity that took place at the test section after the cloud was activated. As the main altitude airflow interacts with the icing cloud, their thermodynamic properties undergo substantial changes. Due to the particle nature of the icing cloud, the droplets and ice crystals tend to redistribute within the cloud as it propagates with the main flow. Data will be presented that shows how these factors affect the thermodynamic property distribution within the icing cloud. A discussion is given of the thermal balances in the icing cloud, between the evaporating spray droplets and the airflow, as a basis for interpreting the measured results.

Crystal Icing↗

NASA NTRSDate not supplied

Comparisons of CFD Simulations of Icing Wind Tunnel Clouds with Experiments Conducted at the NASA Propulsions Systems Laboratory

This paper evaluates simulation predictions against experimental test data of icing clouds that were produced during 2018 ice crystal icing physics tests conducted at the NASA Propulsion Systems Laboratory icing wind tunnel. Aero-thermal and cloud parameters are set and known upstream at the tunnel inlet and spray system, but change as the cloud and air thermodynamically interact as the flowing masses reach the tunnel test section. Utilizing the ANSYS Fluent Discrete Phase Model function, 3D computational fluid dynamics (CFD) simulations were performed, capturing the thermodynamic interactions between the test parameters, and providing predictions of the aero thermal and cloud conditions at the tunnel test section. Simulation predictions were compared with test data that were measured at the tunnel exit plane. Evaluations focused on the cloud concentration (total water content), humidity content, and air temperature. CFD simulation predictions showed areas of agreement and disagreement. Simulations showed that cloud concentration profiles at the test section are strongly related to the initial spray nozzle pattern used at the tunnel inlet. Experimental data suggest that greater dispersion of the cloud occurred as the simulated cloud predicted areas of high and low cloud concentration compared to test data profiles. Simulations, however, captured the magnitude and location of the change in humidity content and the change in air temperature due to the presence of the cloud reasonably well, when compared to test data. This result would suggest that while the ANSYS simulation did not fully predict the spreading of the cloud as measured during experiment, it did capture evaporation and the molecular movements of air and vapor relatively well.

CFD↗

NASA NTRSDate not supplied

Plans for Ice Crystal Icing Tests Using a 3D Heated Test Article at the NASA Icing Research Tunnel

This presentation describes the plans for ice crystal icing and supercooled water icing tests to be conducted in Fall/Winter 2021 at the NASA Icing Research Tunnel. A test article, whose geometry is representative of an inter-compressor duct and strut region of a turbofan engine, has been designed and fabricated for the study of ice crystal icing physics tests. The Simulated Inter-compressor Duct Research Model (SIDRM) will have the ability to heat surfaces to simulate the warm surfaces of the inter-compressor duct within an engine. The test article is instrumented with heaters, heat flux gauges, thermocouples, and pressure taps to measure icing behavior. The aim of these tests is to generate ice shapes on the SIDRM test article under well-characterized conditions. The results of the testing with the SIDRM model will be used to provide icing physics and validation data for development of the engine icing simulation capabilities in GlennICE, the 3D ice prediction tool. This is intended to be a presentation only, and does not have an accompanying paper.

ice-crystal icing↗

NASA NTRSDate not supplied

Evaluation of a Thermodynamic Ice Crystal Accretion Model using Experimental Data from NASA’s 2nd Fundamental Ice Crystal Icing Test

A thermodynamic model describing ice crystal icing is evaluated using experimental data collected at NASA Propulsion Systems Laboratory. The model makes the distinction between ice accretions that are "freeze-dominated" and "melt-dominated". Freeze-dominated icing occurs when partially melted ice crystals impact a surface and freeze. This type of icing is characterized by strong adhesion. This contrasts with melt-dominated icing, where un-melted ice crystals adhere to a surface. This type of icing is characterized by weak adhesion. In this paper, the thermodynamic model is used to analyze the ice growth rates and facility conditions to explain possible phenomena such as mass loss as well as the melting and freezing fractions. Previous analyses assumed a collection efficiency of unity at the leading edge of the experimental model. LEWICE is used to determine a better estimate of the collection efficiency at the model leading edge as ice accretion grows in time. The result shows that the sticking efficiency could change in a greater percent with time than previously reported.

Ice Crystal Icing↗

NASA NTRSDate not supplied

Introduction to Aircraft Icing and NASA's Approach to Understanding It

This presentation provides an introduction to aircraft icing and describes NASA’s approach to understanding it. The presentation covers various topics on icing. A general overview of different types of icing is provided, which includes airframe icing, jet engine icing, and rotorcraft icing. The presentation discusses NASA’s approach to studying the various forms of aircraft icing, which includes conducting flight tests, performing ground-based icing wind tunnel tests, and developing computational tools that simulate the icing physics. An overview on the future of aviation and icing is provided. The presentation is largely high level, but also provides some technical icing physics discussion.

Aircraft Icing↗

NASA NTRSDate not supplied

NASA Icing Update

NASA icing research summarizes work in the following areas: facility updates for the Icing Research Tunnel and Propulsion Systems Laboratory, engine icing, and simulation & experimental tools.

Icing↗