T Shane Sowers | Engineering Papers

NASA NTRS2026

Preliminary Dynamic Modeling of the Quarter-Scale Distributed Electric Propulsion Aircraft

This paper describes the early-stage modeling of a quarter-scale distributed electric propulsion aircraft, based on the SUbsonic Single Aft eNgine (SUSAN) Electrofan, a transformative concept aircraft for which a model exists. The full-scale 180 passenger SUSAN concept has a single turbofan engine in the tail that both produces thrust and provides electrical power to 16 electric fans distributed across the wings utilizing a series/parallel hybrid architecture. The quarter-scale version would have an internal combustion piston engine to provide power to 17 electric fans–16 on the wings, one in the tail–in a series hybrid configuration, and no vertical or horizontal stabilizers. It would also have a reduced flight envelope in terms of both altitude and speed. The initial modeling approach is to scale down the original airframe model to capture the dynamic behavior of a much smaller aircraft, albeit with an empennage. The original powertrain model is then replaced with one representing the physical components of that of the quarter-scale vehicle. This powertrain model is suitable for control design and analysis, and the fully integrated, although preliminary, aircraft model allows flight simulator testing and evaluation. Results from simulations are presented.

Electrified powertrain↗

NASA NTRS2025

Influence of Actuator Movement Rate During Acquisition of Inlet Characterization Data

This report considers using a process to acquire performance data for supersonic mixed-compression inlets that is faster and less costly than the previous process. In the previous process for acquiring data during wind tunnel experiments, actuators for backpressuring an inlet moved in discrete increments, paused for dynamics to dampen, measured data for 5 s, recorded the data, and then reduced the data to graphic plots of pressure recovery versus mass capture ratio. This discrete data acquisition procedure was methodical, reliable, and accurate. However, acquiring data to characterize the inlet consumed significant wind-on time. Wind tunnel operation was costly when considering maintenance, energy, and human resources (operators and research team); therefore, the price for each data point was high. This report presents a quicker method to obtain all measurements, one which can also be used in blowdown wind tunnels. This approach, identified as the dynamic inlet characteristic data acquisition procedure, uses in situ dynamic high-speed pressure sensors to measure pressure signals. The backpressuring actuator moves continuously, and measurements from high-speed pressure sensors are recorded as the actuator progresses to and past the incremental points. Despite its advantages, the approach raised the following questions: (1) Will the new process be as accurate as the previous process? and (2) Are there any hidden costs? These concerns are addressed in this report. This report reviews a study that was undertaken to compare wind tunnel experiment data taken using the previous discrete data acquisition procedure with data recorded using the dynamic inlet characterization data acquisition procedure. In this report, the wind tunnel experiment and the study objectives are described. The processes to reduce the data for analysis are explained, and a discussion of the results is given. Finally, conclusions from this study that may guide further work in this area are presented.

Inlet Characterization Curves↗

NASA NTRS2022

An Analysis of the Impact of Extreme Attitude Operation on a Turbofan Engine in a Regional Jet Aircraft

The objective of this work is to characterize the variability in engine performance at extreme attitudes, resulting from the use of different standard control variables, evaluated at different points in the engine’s lifecycle. This paper describes the procedure used to create a dynamic model of an aft-mounted jet engine on a T-tail regional jet aircraft. This model enables simulation of engine operation at extreme attitudes. The model was subsequently evaluated at various altitudes, Mach numbers, and power settings over a range of angles of attack and sideslip, and deterioration levels. Each case was simulated using both fan speed and engine pressure ratio as the engine control variable. The results show that the wing has a very large impact on the engine operation, overwhelming other sources of variation.

loss of control - inflight↗

NASA NTRSDate not supplied

Implementation Approach for an Electrified Aircraft Concept Vehicle in a Research Flight Simulator

This paper describes a process to develop a flight simulation test capability for the SUbsonic Single Aft eNgine (SUSAN) Electrofan, a subsonic regional jet transport aircraft concept that utilizes electrified propulsion to gain benefits in fuel usage, emissions, and cost. The process, which involves the integration of independently developed models and their subsequent implementation in a flight simulator, is general and can be applied to a variety of aircraft types. However, the use of electrified propulsion architectures has the potential to add complexity beyond that of a traditional aircraft, especially with regard to the pilot interface. The way the pilot interacts with the thrust producing components could vary significantly between architectures, and the information displayed to the pilot will necessarily include additional variables beyond what is normally displayed in a traditional cockpit. This paper describes the integration process in general, as well as specific accommodations made for the architecture under consideration.

electrified aircraft propulsion↗

NASA NTRSDate not supplied

Flight Simulator Demonstration and Certification Implications of Powertrain Failure Mitigation in a Partial Turboelectric Aircraft

The Single-aisle Turboelectric AiRCraft with Aft Boundary Layer propulsor (STARC ABL) is a concept aircraft with a partial turboelectric powertrain. The complexity and integrated nature of the partial turboelectric powertrain architecture presents failure modes and hazards not found in conventional aircraft propulsion designs. Previously, various electrical and mechanical faults and associated recovery modes were demonstrated in a dynamic model of the powertrain. It was shown that certain faults were catastrophic without recovery logic, due specifically to the interaction of the subsystems. However, in each case, the logic, known as a reversionary control mode, enabled continued operation with assumed sufficient thrust to maintain safe flight. The current work evaluates the powertrain faults and recovery strategies using a full aircraft model in a piloted flight simulator, and places it in the context of current regulatory practice. Faults initiated in flight were successfully mitigated, with the accommodated aircraft subsequently evaluated against certification requirements for three-engine aircraft, which were shown to be appropriate for the STARC-ABL configuration.

STARC-ABL↗

NASA NTRSDate not supplied

Flight Simulator Demonstration and Certification Implications of Powertrain Failure Mitigation in a Partial Turboelectric Aircraft

The Single-aisle Turboelectric AiRCraft with Aft Boundary Layer propulsor (STARC ABL) is a concept aircraft with a partial turboelectric powertrain. The complexity and integrated nature of the partial turboelectric powertrain architecture presents failure modes and hazards not found in conventional aircraft propulsion designs. Previously, various electrical and mechanical faults and associated recovery modes were demonstrated in a dynamic model of the powertrain. It was shown that certain faults were catastrophic without recovery logic, due specifically to the interaction of the subsystems. However, in each case, the logic, known as a reversionary control mode, enabled continued operation with assumed sufficient thrust to maintain safe flight. The current work evaluates the powertrain faults and recovery strategies using a full aircraft model in a piloted flight simulator, and places it in the context of current regulatory practice. Faults initiated in flight were successfully mitigated, with the accommodated aircraft subsequently evaluated against certification requirements for three-engine aircraft, which were shown to be appropriate for the STARC-ABL configuration.

STARC-ABL↗

NASA NTRSDate not supplied

Piloted Evaluation of a Fault Recovery System for an Aircraft with Distributed Electric Propulsion

Electrified aircraft powertrains contain multiple tightly coupled subsystems, making them much more complex than traditional aircraft propulsion systems, both in terms of integration and control. Electrification enables aircraft to have multiple distributed thrust-producing fans that the flight control system can utilize for enhanced maneuverability, further increasing the control complexity. The SUbsonic Single Aft eNgine (SUSAN) Electrofan is a NASA concept aircraft that leverages this technology. SUSAN is a series/parallel partial hybrid electric single-aisle transport aircraft that takes advantage of its electrified powertrain to provide fuel burn and emissions benefits when compared to the state-of-the-art. Achieving these benefits requires an appropriately designed control architecture that coordinates the various powertrain and flight control subsystems. As such, the SUSAN aircraft is designed with a high level of automation, allowing it to properly manage coupled subsystems and react rapidly to failures and anomalies. To do this effectively, algorithms that perform component health management, fault detection, isolation, and accommodation, and continuous optimization, must be developed, tested, validated, and implemented. This paper describes a piloted evaluation of such an algorithm in scenarios with multiple fan failures, performed in a flight simulator, demonstrating failure recovery and continued safe operation up to the limits of the powertrain. These scenarios are subsequently related to certification requirements.

Electrified Aircraft Propulsion↗

NASA NTRSDate not supplied

Piloted Evaluation of a Fault Recovery System for an Aircraft with Distributed Electric Propulsion

Electrified aircraft powertrains contain multiple tightly coupled subsystems, making them much more complex than traditional aircraft propulsion systems, both in terms of integration and control. Electrification enables aircraft to have multiple distributed thrust-producing fans that the flight control system can utilize for enhanced maneuverability, further increasing the control complexity. The SUbsonic Single Aft eNgine (SUSAN) Electrofan is a NASA concept aircraft that leverages this technology. SUSAN is a series/parallel partial hybrid electric single-aisle transport aircraft that takes advantage of its electrified powertrain to provide fuel burn and emissions benefits when compared to the state-of-the-art. Achieving these benefits requires an appropriately designed control architecture that coordinates the various powertrain and flight control subsystems. As such, the SUSAN aircraft is designed with a high level of automation, allowing it to properly manage coupled subsystems and react rapidly to failures and anomalies. To do this effectively, algorithms that perform component health management, fault detection, isolation, and accommodation, and continuous optimization, must be developed, tested, validated, and implemented. This paper describes a piloted evaluation of such an algorithm in scenarios with multiple fan failures, performed in a flight simulator, demonstrating failure recovery and continued safe operation up to the limits of the powertrain. These scenarios are subsequently related to certification requirements.

Electrified Aircraft Propulsion↗

NASA NTRSDate not supplied

An Efficient Approach to Collect Inlet Characterization Data

This report considers a novel process to acquire performance data for supersonic mixed compression inlets that is faster, and therefore less costly, than the previous one. In the previous process, measurements were recorded in discrete increments. The backpressuring actuator was advanced, there was a pause to allow for airflow fluctuations to diminish, and then the measurements were recorded. While this process was methodical, reliable and accurate, it consumed significant wind-on time. In general, high-speed wind tunnels are expensive to operate considering maintenance, energy and human resource requirements. Furthermore, many facilities, such as blowdown wind tunnels, are limited in the duration that they can maintain the desired test condition. Consequently, a quick method to collect the measurements is desired. A favored approach has the actuator moving in a continuous fashion with measurements recorded as the actuator continuously progresses through the increment points. This approach, identified as the dynamic inlet characteristic data acquisition procedure, uses in situ dynamic high-speed pressure sensors to measure pressure signals. While faster, continuous movement adds dynamic effects to the data. To better understand these dynamic effects and other potential influences, a study was undertaken to compare wind tunnel measurements taken at discrete actuator position points with data gathered during continuous actuator movement. Specially, plots of inlet pressure recovery versus mass capture ratio, or total pressure characteristic curves, were examined. The data were measured during experiments in the NASA Glenn Research Center Abe Silverstein 10- by 10-Foot Supersonic Wind Tunnel (SWT) with an inlet propulsion test article. In this report, the wind tunnel experiment and the study objectives are described. The processes to reduce the data and for analysis are explained. A discussion of the results along with features noted in the data is given. Finally, conclusions from this study that may be used to guide future wind tunnel experiment planning are presented.

Inlet↗

NASA NTRSDate not supplied

Preliminary Dynamic Modeling of the Quarter-Scale Distributed Electric Propulsion Aircraft

This paper describes the early-stage modeling of a quarter-scale distributed electric propulsion aircraft, based on the SUbsonic Single Aft eNgine (SUSAN) Electrofan, a transformative concept aircraft for which a model exists. The full-scale 180 passenger SUSAN concept has a single turbofan engine in the tail that both produces thrust and provides electrical power to 16 electric fans distributed across the wings utilizing a series/parallel hybrid architecture. The quarter-scale version would have an internal combustion piston engine to provide power to 17 electric fans–16 on the wings, one in the tail–in a series hybrid configuration, and no vertical or horizontal stabilizers. It would also have a reduced flight envelope in terms of both altitude and speed. The initial modeling approach is to scale down the original airframe model to capture the dynamic behavior of a much smaller aircraft, albeit with an empennage. The original powertrain model is then replaced with one representing the physical components of that of the quarter-scale vehicle. This powertrain model is suitable for control design and analysis, and the fully integrated, although preliminary, aircraft model allows flight simulator testing and evaluation. Results from simulations are presented.

electrified aircraft propulsion↗

NASA NTRSDate not supplied

Preliminary Dynamic Modeling of the Quarter-Scale Distributed Electric Propulsion Aircraft

This presentation describes the early-stage modeling of a quarter-scale distributed electric propulsion aircraft, based on the SUbsonic Single Aft eNgine (SUSAN) Electrofan, a transformative concept aircraft for which a model exists. The full-scale 180 passenger SUSAN concept has a single turbofan engine in the tail that both produces thrust and provides electrical power to 16 electric fans distributed across the wings utilizing a series/parallel hybrid architecture. The quarter-scale version would have an internal combustion piston engine to provide power to 17 electric fans–16 on the wings, one in the tail–in a series hybrid configuration, and no vertical or horizontal stabilizers. It would also have a reduced flight envelope in terms of both altitude and speed. The initial modeling approach is to scale down the original airframe model to capture the dynamic behavior of a much smaller aircraft, albeit with an empennage. The original powertrain model is then replaced with one representing the physical components of that of the quarter-scale vehicle. This powertrain model is suitable for control design and analysis, and the fully integrated, although preliminary, aircraft model allows flight simulator testing and evaluation. Results from simulations are presented.

electrified aircraft propulsion↗

NASA NTRSDate not supplied

An Efficient Approach to Collect Inlet Characterization Data

This report considers a novel process to acquire performance data for supersonic mixed compression inlets that is faster, and therefore less costly, than the previous one. In the previous process, measurements were recorded in discrete increments. The backpressuring actuator was advanced, there was a pause to allow for airflow fluctuations to diminish, and then the measurements were recorded. While this process was methodical, reliable and accurate, it consumed significant wind-on time. In general, high-speed wind tunnels are expensive to operate considering maintenance, energy and human resource requirements. Furthermore, many facilities, such as blowdown wind tunnels, are limited in the duration that they can maintain the desired test condition. Consequently, a quick method to collect the measurements is desired. A favored approach has the actuator moving in a continuous fashion with measurements recorded as the actuator continuously progresses through the increment points. This approach, identified as the dynamic inlet characteristic data acquisition procedure, uses in situ dynamic high-speed pressure sensors to measure pressure signals. While faster, continuous movement adds dynamic effects to the data. To better understand these dynamic effects and other potential influences, a study was undertaken to compare wind tunnel measurements taken at discrete actuator position points with data gathered during continuous actuator movement. Specially, plots of inlet pressure recovery versus mass capture ratio, or total pressure characteristic curves, were examined. The data were measured during experiments in the NASA Glenn Research Center Abe Silverstein 10- by 10-Foot Supersonic Wind Tunnel (SWT) with an inlet propulsion test article. In this report, the wind tunnel experiment and the study objectives are described. The processes to reduce the data and for analysis are explained. A discussion of the results along with features noted in the data is given. Finally, conclusions from this study that may be used to guide future wind tunnel experiment planning are presented.

Data Acquisition↗