Engineering topics

Szakaly, Z.

Publications and source records attributed to Szakaly, Z..

4 records

NASA NTRS1990

Impact of end effector technology on telemanipulation performance

Generic requirements for end effector design are briefly summarized as derived from generic functional and operational requirements. Included is a brief summary of terms and definitions related to end effector technology. The second part contains a brief overview of end effector technology work as JPL during the past ten years, with emphasis on the evolution of new mechanical, sensing and control capabilities of end effectors. The third and major part is devoted to the description of current end effector technology. The ongoing work addresses mechanical, sensing and control details with emphasis on mechanical ruggedness, increased resolution in sensing, and close electronic and control integration with overall telemanipulator control system.

Bejczy, A. K.↗

NASA NTRS1990

A laboratory breadboard system for dual-arm teleoperation

The computing architecture of a novel dual-arm teleoperation system is described. The novelty of this system is that: (1) the master arm is not a replica of the slave arm; it is unspecific to any manipulator and can be used for the control of various robot arms with software modifications; and (2) the force feedback to the general purpose master arm is derived from force-torque sensor data originating from the slave hand. The computing architecture of this breadboard system is a fully synchronized pipeline with unique methods for data handling, communication and mathematical transformations. The computing system is modular, thus inherently extendable. The local control loops at both sites operate at 100 Hz rate, and the end-to-end bilateral (force-reflecting) control loop operates at 200 Hz rate, each loop without interpolation. This provides high-fidelity control. This end-to-end system elevates teleoperation to a new level of capabilities via the use of sensors, microprocessors, novel electronics, and real-time graphics displays. A description is given of a graphic simulation system connected to the dual-arm teleoperation breadboard system. High-fidelity graphic simulation of a telerobot (called Phantom Robot) is used for preview and predictive displays for planning and for real-time control under several seconds communication time delay conditions. High fidelity graphic simulation is obtained by using appropriate calibration techniques.

Bejczy, A. K.↗

NASA NTRS1989

Force-reflective teleoperated system with shared and compliant control capabilities

The force-reflecting teleoperator breadboard is described. It is the first system among available Research and Development systems with the following combined capabilities: (1) The master input device is not a replica of the slave arm. It is a general purpose device which can be applied to the control of different robot arms through proper mathematical transformations. (2) Force reflection generated in the master hand controller is referenced to forces and moments measured by a six DOF force-moment sensor at the base of the robot hand. (3) The system permits a smooth spectrum of operations between full manual, shared manual and automatic, and full automatic (called traded) control. (4) The system can be operated with variable compliance or stiffness in force-reflecting control. Some of the key points of the system are the data handling and computing architecture, the communication method, and the handling of mathematical transformations. The architecture is a fully synchronized pipeline. The communication method achieves optimal use of a parallel communication channel between the local and remote computing nodes. A time delay box is also implemented in this communication channel permitting experiments with up to 8 sec time delay. The mathematical transformations are computed faster than 1 msec so that control at each node can be operated at 1 kHz servo rate without interpolation. This results in an overall force-reflecting loop rate of 200 Hz.

Szakaly, Z.↗

NASA NTRS1987

Computing architecture for telerobots in earth orbit

Based on generic operational and computational requirements associated with the control of telerobots in earth orbit, a multibus-based distributed but integrated computing architecture is proposed. An experimental system of that kind under development at the Jet Propulsion Laboratory (JPL) is briefly described. It uses Intel Multibus I at both control station and remote robot (telerobot) computing nodes. An essential element within each multibus is a Unified (or Universal) Computer Control Subsystem (UCCS) for telerobot and control station motor components. The two multibus-based computing nodes can be linked by parallel or high speed serial links for real-time data transmission and for closing the real-time bilateral (force-reflecting) control loop between telerobot and control station. The experimental system is briefly commented, followed by a brief discussion of future development plans and possibilities.

Bejczy, A. K.↗