Processing-microstructure relationships in ferrous alloys via mixed powder laser powder bed fusion
Not Available
Materials Science↗
Engineering topics
Sundararaghavan, Veera
Publications and source records attributed to Sundararaghavan, Veera.
A combined experimental and crystal plasticity study of grain size effects in magnesium alloys
This work presents a method to incorporate the micro Hall-Petch equation into the crystal plasticity finite element (CPFE) framework accounting for the microstructural features to understand the coupling between grain size, texture, and loading direction in magnesium alloys. The effect of grain size and texture is accounted for by modifying the slip resistances of individual basal and prismatic systems based on the micro Hall-Petch equation. The modification based on the micro Hall-Petch equation endows every slip system at each microstructural point with a slip system-level grain size and maximum compatibility factor, which are in turn used to modify the slip resistance. While the slip-system level grain size is a measure of the grain size, the maximum compatibility factor encodes the effect of the grain boundary on the slip system resistance modification and is computed based on the Luster-Morris factor. The model is calibrated using experimental stress-strain curves of Mg-4Al samples with three different grain sizes from which the Hall-Petch coefficients are extracted and compared with Hall-Petch coefficients predicted using original parameters from previous work. The predictability of the model is then evaluated for a Mg-4Al sample with different texture and three grain sizes subjected to loading in different directions. The calibrated parameters are then used for some parametric studies to investigate the variation of Hall-Petch slope for different degrees of simulated spread in basal texture, variation of Hall-Petch slope with loading direction relative to basal poles for a microstructure with strong basal texture, and variation of yield strength with change in grain morphology. The proposed approach to incorporate the micro Hall-Petch equation into the CPFE framework provides a foundation to quantitatively model more complicated scenarios of coupling between grain size, texture and loading direction in the plasticity of Mg alloys.
Crystal plasticity↗
Incorporating dynamic recrystallization into a crystal plasticity model for high-temperature deformation of Ti-6Al-4V
During hot deformation of (α + β) titanium alloys, the simultaneous action of strain and temperature in the (α + β) regime facilitates dynamic recovery, dynamic recrystallization (DRX), and phase transformations via non-equilibrium paths. DRX is manifested in the form of fine recrystallized α or β grains. Here, in the present study, a two-phase crystal plasticity finite element framework (CP-DRX) has been developed which incorporates DRX kinetics into the crystal plasticity (CP) model to predict the flow characteristics of Ti-6Al-4V alloys during thermo-mechanical processing. The CP slip system parameters, as well as elastic properties from both α and β phases of Ti, are calibrated for different strain rate conditions. An EBSD-informed two-phase microstructure representation has been utilized in the CP-DRX framework to explore the time-dependent evolution of DRX microstructure and crystal orientation for different strain rate conditions. The proposed CP-DRX can capture the evolution of crystal orientation and plastic flow stress–strain response of polycrystalline Ti-6Al-4V during the deformation process. Furthermore, the proposed model is able to capture the softening behavior, observed in average stress–strain response from experiments performed using a Gleeble thermomechanical simulator and predict the recrystallization texture.
(α+ β)-Titanium (Ti) Alloys↗
The effects of microstructure on deformation twinning in Mg WE43
The interplay between microstructure and deformation twinning in a WE43-T6 Mg alloy under uniaxial compression was investigated using a combination of scanning electron microscopy with digital image correlation (SEM-DIC) and crystal plasticity finite element (CPFE) simulation. To improve understanding of the statistical characteristics of deformation twin formation, microstructural effects were characterized in over 1000 grains through metrics including the nominal Schmid Factor, grain size, geometric compatibility factor (m'), residual Burgers vector, and the strain accommodated by neighboring grains. There was a strong correlation between the nominal Schmid Factor and both twin activation and variant selection, but this was not fully deterministic. Deformation twinning also exhibited a strong dependence on existing slip and twinning in the neighboring grain and on the m' value. Within the range of grain sizes present in this condition, grain size was determined to have minimal effect on deformation twinning. Finally, statistical analysis of CPFE simulations was used to further investigate microstructural effects on twinning, and qualitatively captured the effect of the nominal Schmid Factor.
36 MATERIALS SCIENCE↗
PRISMS-Plasticity TM: An Open-Source Rapid Texture Evolution Analysis Pipeline
Not provided.
Engineering↗
Deformation twinning and detwinning in extruded Mg-4Al: In-situ experiment and crystal plasticity simulation
Deformation twinning and detwinning in extruded Mg-4Al were investigated using in-situ SEM-DIC experiments and crystal plasticity finite element (CPFE) simulation. In this study, the in-situ SEM-DIC method was used to provide a unique set of data including twin/detwin characteristics and twin area fraction in addition to strain maps. A statistical analysis of the activation of twin variants and twin area fraction during both twinning and detwinning was conducted. A strong correlation was found between twin growth/shrinkage and the Schmid Factor (SF) for individual twin variants Higher twin SF during loading and unloading led to higher twin growth and shrinkage, respectively. However, after the applied compressive strain was removed, the pattern of the twin area fractions of the residual twin variants versus their nominal SFs did not follow the trend observed at the maximum compressive strain. Using a systematic methodology and an advanced twin/detwin model, the PRISMS-Plasticity CPFE simulation was calibrated using experimentally determined stress versus strain and twin area fraction versus strain information. A comprehensive evaluation of the CPFE model was conducted to determine its ability to capture the statistics of twin variants activation and twin area fraction. CPFE accurately captured the statistical aspects of both twinning and detwinning. Finally, it also predicted the first dominant twin variant for 47.5% of the grains and at least one of the two dominant twin variants for 80% of the grains at maximum compressive strain.
36 MATERIALS SCIENCE↗