Engineering Papers⌕ Search

Engineering topics

Sun, Z.

Publications and source records attributed to Sun, Z..

At least 55 records · Page 3

Real-time gas cooling of flowing liquid lithium limiter for the EAST

A novel continuously flowing liquid lithium limiter (FLiLi) which employs an in-vessel electro-magnetic pump to drive liquid Li flowing on the surface of limiter has been successfully designed and tested in the experimental advanced superconducting tokamak (EAST) device in 2014. In order to better control the surface temperature, an upgraded design and the real-time gas cooling were performed in 2016. Two kinds of cooling gas, helium (He) and argon (Ar) were tested on the FLiLi system prior to the experiment. It was found that the cooling rates of He and Ar at 2.5 MPa are 34.2 °C/min, 10.2 °C/min or 31.7 °C/kL and 28.1 °C/kL, respectively. The cooling performance of He is more effective than Ar. Experimental results show that the real-time He cooling could effectively contain the FLiLi surface temperature increase and prevent the strong passive evaporation of lithium during plasma discharges. Limiter heat flux up to 0.2 MW/m2 was removed during ohmic discharge with 2.5 MPa He gas. Finally, Because of the upgraded design and real-time gas cooling, the surface of FLiLi was not damaged by heat flux after entire plasma discharge.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Simulation of supersonic molecular beam injection fueling into H-mode plasmas on EAST using BOUT++

Transport dynamic 2D simulations for supersonic molecular beam injection (SMBI) fueling into H-mode deuterium plasmas on the Experimental Advanced Superconducting Tokamak (EAST) is first simulated using a seven-field two-fluid model in the BOUT++ framework. The SMB is assumed to be injected into plasma from the midplane at the low field side with a fixed width and constant molecular flux. The different densities and injection velocities of SMBI are investigated within the upper single-null geometry of EAST. The simulations indicate that the SMBI has a self-shielding effect on molecules' inward transport into the plasma, and the deposition of SMBI leads to a large increase in plasma density and decrease in plasma temperature. There is a velocity threshold for SMB penetrating the pedestal and depositing at the top of density pedestal. However, the deposition point would be back toward the plasma boundary after SMB arriving at the deepest penetration position. Comparing the different molecular injection velocities and densities, the outcomes demonstrate that the depth of deposition is closely related to the injection velocity rather than the molecular density. The simulated results show good agreement with the EAST experiments by comparing the electron density profiles obtained by simulation and experiment, respectively. These results will be helpful for guiding future experiments, as well as the design of the SMBI system.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

A unified form of low-energy nodal electronic interactions in hole-doped cuprate superconductors

Using angle resolved photoemission spectroscopy measurements of Bi 2 Sr 2 CaCu 2 O 8+δ over a wide range of doping levels, we present a universal form for the non-Fermi liquid electronic interactions in the nodal direction in the exotic normal state phase. It is described by a continuously varying power law exponent versus energy and temperature (hence named a Power Law Liquid or PLL), which with doping varies smoothly from a quadratic Fermi Liquid in the overdoped regime, to a linear Marginal Fermi Liquid at optimal doping, to a non-quasiparticle non-Fermi Liquid in the underdoped regime. The coupling strength is essentially constant across all regimes and is consistent with Planckian dissipation. Using the extracted PLL parameters we reproduce the experimental optics and resistivity over a wide range of doping and normal-state temperature values, including the T* pseudogap temperature scale observed in the resistivity curves. This breaks the direct link to the pseudogapping of antinodal spectral weight observed at similar temperature scales and gives an alternative direction for searches of the microscopic mechanism.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Control of hydrogen content and fuel recycling for long pulse high performance plasma operation in EAST

Control of fuel recycling and hydrogen content in the Experimental Advanced Superconducting Tokamak (EAST) using various methods is studied for high-power long pulse high confinement mode (H-mode) plasma operation. The results show that long duration first wall baking and discharge cleaning in EAST provides the necessary clean vacuum environment with a high ultimate vacuum of 3.6 × 10 -6 Pa and low outgassing rate of ~1.5 × 10 -4 Pa m 3 s -1 for plasma operation. In-vessel cryopumps are found to provide an efficient method for particle recycling control in the divertor region to decrease global recycling coefficient (R global ) from ~1.0 to ~0.8 during ohmic heating plasmas, and it provides a high particle exhausting rate of 10 20_ 10 21 D-atoms s -1 in high-power plasma operations. Long duration silicon coating is found to be more powerful than baking and discharge cleaning, which reduces the H/(H + D) ratio gradually to a value as low as 8%, and lithium coating is more effective and more efficient than silicon coating, to further reduce the H/(H + D) ratio to 3%. Real-time lithium powder injection is a novel method for recycling control, which reduces R global from 0.94 to 0.82 under lithium coating wall conditioning. By the combination and optimization of the above methods, H-mode plasmas with low hydrogen content and low fuel recycling have been achieved in EAST and have been extended gradually to 101 s in 2017. Recycling flux has even decreased gradually during 101 s H-mode plasmas due to increased first wall temperature and the resulting increased Li-II emission. These results provide valuable references on hydrogen content and fuel recycling control for long pulse H-mode plasmas of up to 400–1000 s with high-power heating in EAST and future fusion devices.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Advances in plasma–wall interaction control for H-mode operation over 100 s with ITER-like tungsten divertor on EAST

A total power injection up to 0.3 GJ has been achieved in EAST long pulse H-mode operation of 101.2 s with an ITER-like water-cooled tungsten (W) mono-block divertor, which has steady-state power exhaust capability of 10 MWm –2 . The peak temperature of W target saturated at 12 s to the value T ~ 500 °C with a heat flux ~3.3 MW m –2 being maintained during the discharge. By tailoring the 3D divertor plasma footprint through edge magnetic topology change, the heat load was broadly dispersed and thus peak heat flux and W sputtering were well controlled. Active feedback control of H-mode detachment with D 2 fuelling or divertor impurity seeding has been achieved successfully, with excellent compatibility with the core plasma performance. Active feedback control of radiative power utilizing neon seeding was achieved with f rad = 18%–41% in H-mode operation, exhibiting potential for heat flux reduction with divertor and edge radiation. This has been further demonstrated in DIII-D high β P H-mode scenario within the joint DIII-D/EAST experiment using impurity seeding from the divertor volume. Steady-state particle control and impurity exhaust has been achieved for long pulse H-mode operation over 100 s with the W divertor by leveraging the effect of drifts and optimized divertor configuration, coupled with strong pumping and extensive wall conditioning. Methods toward the reduction of divertor W sourcing, which is of crucial importance for a metal-wall tokamak, are also explored. These advances provide vital experimental information on favourable core-edge integration for high power, long-pulse H-mode operation in EAST, ITER and CFETR.

43 PARTICLE ACCELERATORS↗

Hollow pellet injection for magnetic fusion

The precise delivery of mass to burning plasmas is an area of growing interest in magnetic fusion (MF). The amount of mass that is necessary and sufficient can vary depending on such parameters as the type of atoms involved, the type of applications, plasma conditions, mass injector, and injection timing. Motivated by edge localized mode (ELM) control in H-mode plasmas, disruption mitigation and other applications in MF, we report the progress and new possibilities in mass delivery based on hollow pellets. Here, a hollow pellet refers to a spherical shell mass structure with a hollow core. Based on an empirical model of pellet ablation, coupled with BOUT++ simulations of the ELM triggering threshold, hollow pellets are found to be attractive in comparison with solid spheres for ELM control. By using hollow pellets, it is possible to tailor mass delivery to certain regions of edge plasmas while minimizing core contamination and reducing the total amount of mass needed. We also include the experimental progress in mass delivery experiments, in situ diagnostics and hollow pellet fabrication, and emphasize new experimental possibilities for ELM control based on hollow pellets. A related application is the disruption mitigation scheme using powder encapsulated inside hollow shells. Further experiments will also help to resolve known discrepancies between theoretical predictions and experiments in using mass injection for ELM control and leading to better predictive models for ELM stability and triggering.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Results from an improved flowing liquid lithium limiter with increased flow uniformity in high power plasmas in EAST

Significant engineering and physic progress was made by the upgrade of a flowing liquid lithium limiter (FLiLi) inserted into EAST H-mode discharges in 2016. The progress includes an improvement of liquid Li coverage uniformity, no macroscopic surface erosion by plasma materials interaction, effective removal of 55% of the discharge heat flux using high pressure He cooling during ohmic discharges, and the demonstrated ability to restart Li flow for a second experiment performed a week after the first. With increasing Li flow rate, fuel particle recycling and Fe impurity radiation gradually decreased, and plasma performance slightly improved, but there was no impact on the edge tungsten influx. No obvious Li bursts appeared during operation with up to about 4.5 MW auxiliary heating power with peak heat flux reaching ~4 MW m –2 on FLiLi. In addition, a gradual mitigation of edge localized mode (ELM) activity was observed with FLiLi operation. Lastly, short-lived ELM-free phases were observed for the first time in EAST during FLiLi insertion, with increasing τ E and transient H 98(y, 2) < 2.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

ELM frequency enhancement and discharge modification through lithium granule injection into EAST H-modes

The injection of impurity granules into fusion research discharges can serve as a catalyst for ELM events. For sufficiently low ELM frequencies, and granule sizes above a threshold, this can result in full control of the ELM cycle, referred to as ELM pacing. For this research, we extend the investigation to conditions where the natural ELM frequency is too high for ELM pacing to be realized. Utilizing multiple sizes of lithium granules and classifying their effects by granule size, we demonstrate that ELM mitigation through frequency multiplication can be used at ELM triggering rates that nominally make ELM pacing unrealizable. We find that above a size threshold, injected granules promptly trigger ELMs and commensurately enhance the ELM frequency. Below this threshold size, injection of an individual granule does not always lead to the prompt triggering of an ELM; however, collective ablation in the edge pedestal region does enhance the ELM frequency. Furthermore, Li granules too small to individually trigger ELMs were injected into EAST H-mode discharges at frequencies up to 2.3 kHz; collectively the granules were observed to enhance the natural ELM frequency up to 620 Hz, resulting in a ~2.4 × multiplication of the natural ELM frequency and a 50% decrease of the ELM size.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Real-time reduction of tungsten impurity influx using lithium powder injection in EAST

We report the first successful use of solid material injection, in powder form, to reduce core tungsten impurities in EAST discharges with tungsten divertor plasma-facing components. Tungsten is the leading plasma-facing material for use in ITER as well as future fusion devices. However, tungsten sometimes accumulates in the plasma core of fusion devices, which is an impediment to the achievement of high-power, long-pulse H-modes. In this work, tungsten impurity influx from the tungsten divertor was reduced by real-time injection of lithium powder into EAST discharges. An increase in stored energy and confinement accompanied the sharp reduction of core tungsten with real-time lithium powder injection in L-mode discharges. In H-mode discharges, real-time lithium powder injection reduced the tungsten core impurity emission while also mitigating ELMs. During powder injection, the divertor electron temperature was reduced, which reduced the tungsten source. In conclusion, the tungsten impurity emission remained low in discharges even after active lithium injection was terminated, a signature of improved and lasting wall conditioning in the tungsten divertor.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Improving the Strength of the ZrC-SiC and TC4 Brazed Joint Through Fabricating Graded Double-Layered Composite Structure on TC4 Surface

In order to improve the ZrC-SiC ceramic and TC4 brazed joint property, graded double-layered SiC particles (SiCp)-reinforced TC4-based composite structure (named as GLS for convenience) was designed to relieve the residual stress in the joint. The GLS was successfully fabricated on TC4 substrate by double-layered laser deposition technology before the brazing process. The investigation of the GLS shows that the volume fraction of SiCp in the two composite layers was graded (20 and 39 vol pct, respectively). Ti{sub 5}Si{sub 3} and TiC phases formed in the GLS due to the reaction of SiCp and TC4. The laser power-II (the laser power for the second deposition layer) affected the microstructure of the GLS significantly. Increasing the laser power-II would promote the reaction between the SiCp and TC4. But the high laser power-II made the layer I remelt completely and the two layers became homogeneous rather than graded structure. In the ZrC-SiC and TC4 brazed joint, the CTE (coefficient of thermal expansion) was graded from the TC4 to the ZrC-SiC due to the GLS, and the strength of the joint with the GLS (91 MPa) was higher than that without the GLS (43 MPa).

36 MATERIALS SCIENCE↗

A new developed in-between shots lithium evaporation coating system for improving plasma performance in EAST

A new in-between shots evaporative lithium coating system has been successfully developed and implemented on the Experimental Advanced Superconducting Tokamak (EAST) for the 2017 campaign. This paper describes a novel technique for the introduction of lithium into the EAST vessel allowing evaporative coatings to be applied between discharges without requiring a significant amount of time to insert and retract the lithium source. This newly designed system utilizes a rotating axis driven by a vacuum dynamic sealing feedthough under remote control to open and close a shutter. A compression bellows, which drives the delivery tube, guarantees accurate position of the oven thus avoiding possible direct contact with the plasma. This allows the new evaporation system to be operated in two distinct modes. One mode is operated in-between shots to refresh pre-coated lithium film, the other is a real-time lithium vapor injection during plasma operations to provide active wall conditioning during long pulse plasma discharges. In this paper, operation of this new lithium deposition system in the in-between shots replenishment mode is described. Initial experiments show that this system worked well during the interval of discharges in EAST, and the in-between shots lithium coating effectively reduced the wall recycling and impurity concentrations. Furthermore, the application of fresh lithium coating lead to sustain the plasma stored energy and confinement, as well as a reduction of impurity radiation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Reduction of hydrogen content in deuterium plasma with mixed graphite and tungsten divertors in EAST

Reduction of hydrogen content in deuterium-fueled fusion plasmas is important not only to avoid diluting reacting core deuterons but also so as to allow the optimization of hydrogen-minority-heating efficiency in those fusion devices which employ ion-cyclotron-radio-frequency heating systems. In EAST, the amount of hydrogen released from plasma-facing components has been shown to depend strongly on both their composition and their temperature. In this paper, as measured by thermal desorption spectroscopy, the hydrogen inventory in graphite – used in EAST as lower divertor material – has been determined to be >25 times larger than that of tungsten which comprises the upper divertor. This difference in hydrogen inventory is attributed mostly to the intrinsically porous nature of bulk graphite. Thus the main source of hydrogen release into EAST discharges was identified as the graphite tiles used in the lower divertor. The hydrogen content in EAST plasmas were clearly reduced by first employing a high-temperature vacuum baking of all graphite tiles and then renewing a 100–200 μm thick SiC coating before an EAST experimental run campaign. Subsequent active surface conditioning of all wall components with elemental silicon and then with elemental lithium were seem to again reduce the plasma hydrogen content significantly – with lithium proving to be more effective than silicon. Combining these several techniques, H/(H + D) levels as low as ~3% have been achieved in EAST discharges. Additionally, the effects of lithium thickness on H surface implantation and retention has been re-examined semi-quantitatively using data from a previous run campaign. These data suggest that relatively thick Li films coated on the first wall can effectively isolate the rich source of hydrogen stored in the porous bulk of the underlying graphite from the deuterium-fueled plasma so as to minimize hydrogen release. In conclusion, an operational maneuver whereby a diverted plasma is repetitively switched from an upper single null configuration to a lower single null configuration is presented. This switching maneuver has been shown to suppress hydrogen influx into a 35s-long EAST discharge by alternately mitigating the rise in divertor temperature.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Active Recycling Control Through Lithium Injection in EAST

The coating of tokamak walls with thin layers of lithium has been demonstrated to reduce plasma recycling from the plasma-facing surfaces and to improve overall plasma performance. These effects, including reduced divertor D α emission, the elimination of edge-localized modes, and increased energy confinement have been observed in multiple experiments when lithium coatings are applied before plasma discharges. However, this coating technology does not extrapolate to future long-pulse devices, since the lithium coatings will be passivated by the continual plasma flux onto the surface. In order to provide active conditioning capability, a new technology has been developed that is capable of injecting lithium powder into the scrape-off layer plasma during plasma discharges, where it quickly liquefies and turns into an aerosol. The use of this “lithium dropper” is under study at the Experimental Advanced Superconducting Tokamak (EAST), where the potential benefits of real-time wall conditioning via lithium injection are being tested. Here, we present an analysis of the recycling characteristics during EAST experiments testing active lithium injection in order to assess recycling reduction and control. Lithium aerosol was injected from the top of the machine, with one system dropping lithium near the X-point and another into the low-field side divertor leg. The injection of lithium into the SOL reduced divertor recycling, as evidenced by reduced D α emission with ion flux measured by probes relatively unchanged. This effect is strongest in the active divertor, confirming the lithium is transported to strongly plasma-wetted areas. Furthermore, quantitative analysis of the recycling changes using the SOLPS edge plasma and neutral transport code indicated a ~20% reduction in recycling coefficient with lithium injection.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

ELM elimination with Li powder injection in EAST discharges using the tungsten upper divertor

Here, we report the first successful use of lithium (Li) to eliminate edge-localized modes (ELMs) with tungsten divertor plasma-facing components in the EAST device. Li powder injected into the scrape-off layer of the tungsten upper divertor successfully eliminated ELMs for 3–5 s in EAST. The ELM elimination became progressively more effective in consecutive discharges at constant lithium delivery rates, and the divertor D α baseline emission was reduced, both signatures of improved wall conditioning. A modest decrease in stored energy and normalized energy confinement was also observed, but the confinement relative to H98 remained well above 1, extending the previous ELM elimination results via Li injection into the lower carbon divertor in EAST. These results can be compared with recent observations with lithium pellets in ASDEX-Upgrade that failed to mitigate ELMs, highlighting one comparative advantage of continuous powder injection for real-time ELM elimination.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Upgraded flowing liquid lithium limiter for improving Li coverage uniformity and erosion resistance in EAST device

In this paper, we report on design and technology improvements for a flowing liquid lithium (FLiLi) limiter inserted into auxiliary heated discharges in the experimental advanced superconducting tokamak device. In order to enhance Li coverage uniformity and erosion resistance, a new liquid Li distributor with homogenous channels was implemented. In addition, two independent electromagnetic pumps and a new horizontal capillary structure contributed to an improvement in the observed Li flow uniformity (from 30% in the previous FLiLi design to >80% in this FLiLi design). To improve limiter surface erosion resistance, hot isostatic press technology was applied, which improved the thermal contact between thin stainless steel protective layers covering the Cu heat sink. The thickness of the stainless steel layer was increased from 0.1 mm to 0.5 mm, which also helped macroscopic erosion resilience. Finally, despite the high auxiliary heating power up to 4.5 MW, no Li bursts were recorded from FLiLi, underscoring the improved performance of this new design.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

First Results of ELM Triggering With a Multichamber Lithium Granule Injector Into EAST Discharges

A critical challenge facing the basic long-pulse H-mode for ITER is to control edge-localized modes (ELMs). A new method using a multichamber lithium (Li) granule injector (LGI) for ELM triggering experiments has been developed in Experimental Advanced Superconducting Tokamak (EAST). First experimental results of the control of ELMs are obtained in EAST with a tungsten divertor. It is found that the injector has good capacities, i.e., allowing good flexibilities in granule size selection, injection rate, and injection velocity. In conclusion, LGI has successfully triggered ELMs during the H-mode. These results indicate the LGI would be a promising method to control ELMs in long-pulse steady-state tokamaks.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗