Engineering Papers⌕ Search

Engineering topics

Sulyma, P. R.

Publications and source records attributed to Sulyma, P. R..

10 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

ASRM radiation and flowfield prediction status

Existing and proposed methods for the prediction of plume radiation are discussed in terms of their application to the NASA Advanced Solid Rocket Motor (ASRM) and Space Shuttle Main Engine (SSME) projects. Extrapolations of the Solid Rocket Motor (SRM) are discussed with respect to preliminary predictions of the primary and secondary radiation environments. The methodology for radiation and initial plume property predictions are set forth, including a new code for scattering media and independent secondary source models based on flight data. The Monte Carlo code employs a reverse-evaluation approach which traces rays back to their point of absorption in the plume. The SRM sea-level plume model is modified to account for the increased radiation in the ASRM plume due to the ASRM's propellant chemistry. The ASRM cycle-1 environment predictions are shown to identify a potential reason for the shutdown spike identified with pre-SRM staging.

Reardon, J. E.↗
NASA NTRS1983

Low L/D aerobrake test at Mach 10

An aerobraking Orbital transfer vehicle may be used to increase the Space Shuttle mission capability to and from high orbits. A Mach 10 wind-tunnel test was performed for a low lift-drag aerobrake, to define a preliminary aerothermal environment for this candidate concept. Test hardware simulated the ribs and stretched fabric of conceptual flight hardware. Pressures, paint-melting histories, and oilflow data were measured on the brake. Pressure and thermocouple heating rate data were measured on the payload. Brake peak heating is at the edge at all angles of attack, although the stagnation point is not outboard of 75 percent radius even at 20 degrees angle of attack. Brake ribs show slightly higher heating than flats, although pressures are essentially constant. Payload peak heating occurs near 12 degrees angle of attack, and is 30 percent of the sphere stagnation point heating (for a sphere of brake diameter). Payload pressure distributions follow the heating pattern. Reynolds number effects are small on the brake and large on the payload, for the range of test conditions: 0.4-1.0 million/foot.

Hair, L. M.↗
NASA NTRS1980

An analytical procedure and automated computer code used to design model nozzles which meet MSFC base pressure similarity parameter criteria

Fundamental equations and similarity definition and application are described as well as the computational steps of a computer program developed to design model nozzles for wind tunnel tests conducted to define power-on aerodynamic characteristics of the space shuttle over a range of ascent trajectory conditions. The computer code capabilities, a user's guide for the model nozzle design program, and the output format are examined. A program listing is included.

Sulyma, P. R.↗
NASA NTRS1978

Development of base pressure similarity parameters for application to space shuttle launch vehicle power-on aerodynamic testing

A base pressure data correlation study was conducted to define exhaust plume similarity parameters for use in Space Shuttle power-on launch vehicle aerodynamic test programs. Data correlations were performed for single bodies having, respectively, single and triple nozzle configurations and for a triple body configuration with single nozzles on each of the outside bodies. Base pressure similarity parameters were found to differ for the single nozzle and triple nozzle configurations. However, the correlation parameter for each was found to be a strong function of the nozzle exit momentum. Results of the data base evaluation are presented indicating an assessment of all data points. Analytical/experimental data comparisons were made for nozzle calibrations and correction factors derived, where indicated for use in nozzle exit plane data calculations.

Sulyma, P. R.↗
NASA NTRS1976

Supersonic Flow of Chemically Reacting Gas-Particle Mixtures. Volume 2: RAMP - A Computer Code for Analysis of Chemically Reacting Gas-Particle Flows

A computer program written in conjunction with the numerical solution of the flow of chemically reacting gas-particle mixtures was documented. The solution to the set of governing equations was obtained by utilizing the method of characteristics. The equations cast in characteristic form were shown to be formally the same for ideal, frozen, chemical equilibrium and chemical non-equilibrium reacting gas mixtures. The characteristic directions for the gas-particle system are found to be the conventional gas Mach lines, the gas streamlines and the particle streamlines. The basic mesh construction for the flow solution is along streamlines and normals to the streamlines for axisymmetric or two-dimensional flow. The analysis gives detailed information of the supersonic flow and provides for a continuous solution of the nozzle and exhaust plume flow fields. Boundary conditions for the flow solution are either the nozzle wall or the exhaust plume boundary.

Penny, M. M.↗
NASA NTRS1976

Supersonic flow of chemically reacting gas-particle mixtures. Volume 1: A theoretical analysis and development of the numerical solution

A numerical solution for chemically reacting supersonic gas-particle flows in rocket nozzles and exhaust plumes was described. The gas-particle flow solution is fully coupled in that the effects of particle drag and heat transfer between the gas and particle phases are treated. Gas and particles exchange momentum via the drag exerted on the gas by the particles. Energy is exchanged between the phases via heat transfer (convection and/or radiation). Thermochemistry calculations (chemical equilibrium, frozen or chemical kinetics) were shown to be uncoupled from the flow solution and, as such, can be solved separately. The solution to the set of governing equations is obtained by utilizing the method of characteristics. The equations cast in characteristic form are shown to be formally the same for ideal, frozen, chemical equilibrium and chemical non-equilibrium reacting gas mixtures. The particle distribution is represented in the numerical solution by a finite distribution of particle sizes.

Penny, M. M.↗
NASA NTRS1976

Summary of nozzle-exhaust plume flowfield analyses performed in support of space shuttle applications

Results are summarized of various analyses of the exhaust plumes of the space shuttle. Specific topics discussed included: the development of the two-phase plume flow field model, including finite rate chemistry and free molecular effects; analyses of exhaust plume simulation studies; verification of the analytical two-phase plume flow field model; and complete documentation of the two-phase plume computer code.

Smith, S. D.↗
NASA NTRS1976

Assessment of analytical and experimental techniques utilized in conducting plume technology tests 575 and 593

Since exhaust plumes affect vehicle base environment (pressure and heat loads) and the orbiter vehicle aerodynamic control surface effectiveness, an intensive program involving detailed analytical and experimental investigations of the exhaust plume/vehicle interaction was undertaken as a pertinent part of the overall space shuttle development program. The program, called the Plume Technology program, has as its objective the determination of the criteria for simulating rocket engine (in particular, space shuttle propulsion system) plume-induced aerodynamic effects in a wind tunnel environment. The comprehensive experimental program was conducted using test facilities at NASA's Marshall Space Flight Center and Ames Research Center. A post-test examination of some of the experimental results obtained from NASA-MSFC's 14 x 14-inch trisonic wind tunnel is presented. A description is given of the test facility, simulant gas supply system, nozzle hardware, test procedure and test matrix. Analysis of exhaust plume flow fields and comparison of analytical and experimental exhaust plume data are presented.

Baker, L. R.↗
NASA NTRS1975

User's guide and description of the streamline divergence computer program

The streamline divergence program was developed to demonstrate the capability to trace inviscid surface streamlines and to calculate outflow-corrected laminar and turbulent convective heating rates on surfaces subjected to exhaust plume impingement. The analytical techniques used in formulating this program are discussed. A brief description of the streamline divergence program is given along with a user's guide. The program input and output for a sample case are also presented.

Sulyma, P. R.↗