Engineering Papers⌕ Search

Engineering topics

Strawn, Roger C.

Publications and source records attributed to Strawn, Roger C..

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2003

Analysis and Design of Rotors at Ultra-Low Reynolds Numbers

Design tools have been developed for ultra-low Reynolds number rotors, combining enhanced actuator-ring / blade-element theory with airfoil section data based on two-dimensional Navier-Stokes calculations. This performance prediction method is coupled with an optimizer for both design and analysis applications. Performance predictions from these tools have been compared with three-dimensional Navier Stokes analyses and experimental data for a 2.5 cm diameter rotor with chord Reynolds numbers below 10,000. Comparisons among the analyses and experimental data show reasonable agreement both in the global thrust and power required, but the spanwise distributions of these quantities exhibit significant deviations. The study also reveals that three-dimensional and rotational effects significantly change local airfoil section performance. The magnitude of this issue, unique to this operating regime, may limit the applicability of blade-element type methods for detailed rotor design at ultra-low Reynolds numbers, but these methods are still useful for evaluating concept feasibility and rapidly generating initial designs for further analysis and optimization using more advanced tools.

Kunz, Peter J.↗
NASA NTRS2002

CFD Simulations of Tiltrotor Configurations in Hover

Navier-Stokes computational fluid dynamics calculations are presented for isolated, half-span, and full-span V-22 tiltrotor hover configurations. These computational results extend the validity of CFD hover methodology beyond conventional rotorcraft applications to tiltrotor configurations. Computed steady-state, isolated rotor performance agrees well with experimental measurements, showing little sensitivity to grid resolution. However, blade-vortex interaction flowfield details are sensitive to numerical dissipation and are more difficult to model accurately. Time-dependent, dynamic, half- and full-span installed configurations show sensitivities in performance to the tiltrotor fountain flow. As such, the full-span configuration exhibits higher rotor performance and lower airframe download than the half-span configuration. Half-span rotor installation trends match available half-span data, and airframe downloads are reasonably well predicted. Overall, the CFD solutions provide a wealth of flowfield details that can be used to analyze and improve tiltrotor aerodynamic performance.

Potsdam, Mark a.↗
NASA NTRS2002

Computational Analysis of a Prototype Martian Rotorcraft Experiment

This paper presents Reynolds-averaged Navier-Stokes calculations for a prototype Martian rotorcraft. The computations are intended for comparison with an ongoing Mars rotor hover test at NASA Ames Research Center. These computational simulations present a new and challenging problem, since rotors that operate on Mars will experience a unique low Reynolds number and high Mach number environment. Computed results for the 3-D rotor differ substantially from 2-D sectional computations in that the 3-D results exhibit a stall delay phenomenon caused by rotational forces along the blade span. Computational results have yet to be compared to experimental data, but computed performance predictions match the experimental design goals fairly well. In addition, the computed results provide a high level of detail in the rotor wake and blade surface aerodynamics. These details provide an important supplement to the expected experimental performance data.

Corfeld, Kelly J.↗
NASA NTRS2001

Computational Analysis of a Prototype Martian Rotorcraft Experiment

This paper presents Reynolds-averaged Navier-Stokes calculations for a prototype Martian rotorcraft. The computations are intended for comparison with an ongoing Mars rotor hover test at NASA Ames Research Center. These computational simulations present a new and challenging problem, since rotors that operate on Mars will experience a unique low Reynolds number and high Mach number environment. Computed results for the 3-D rotor differ substantially from 2-D sectional computations in that the 3-D results exhibit a stall delay phenomenon caused by rotational forces along the blade span. Computational results have yet to be compared to experimental data, but computed performance predictions match the experimental design goals fairly well. In addition, the computed results provide a high level of detail in the rotor wake and blade surface aerodynamics. These details provide an important supplement to the expected experimental performance data.

Corfeld, Kelly J.↗
NASA NTRS1997

Tetrahedral and Hexahedral Mesh Adaptation for CFD Problems

This paper presents two unstructured mesh adaptation schemes for problems in computational fluid dynamics. The procedures allow localized grid refinement and coarsening to efficiently capture aerodynamic flow features of interest. The first procedure is for purely tetrahedral grids; unfortunately, repeated anisotropic adaptation may significantly deteriorate the quality of the mesh. Hexahedral elements, on the other hand, can be subdivided anisotropically without mesh quality problems. Furthermore, hexahedral meshes yield more accurate solutions than their tetrahedral counterparts for the same number of edges. Both the tetrahedral and hexahedral mesh adaptation procedures use edge-based data structures that facilitate efficient subdivision by allowing individual edges to be marked for refinement or coarsening. However, for hexahedral adaptation, pyramids, prisms, and tetrahedra are used as buffer elements between refined and unrefined regions to eliminate hanging vertices. Computational results indicate that the hexahedral adaptation procedure is a viable alternative to adaptive tetrahedral schemes.

Biswas, Rupak↗
NASA NTRS1996

A Comparison of Lifting-Line and CFD Methods with Flight Test Data from a Research Puma Helicopter

Four lifting-line methods were compared with flight test data from a research Puma helicopter and the accuracy assessed over a wide range of flight speeds. Hybrid Computational Fluid Dynamics (CFD) methods were also examined for two high-speed conditions. A parallel analytical effort was performed with the lifting-line methods to assess the effects of modeling assumptions and this provided insight into the adequacy of these methods for load predictions.

Bousman, William G.↗
NASA NTRS1996

Parallel Implementation of an Adaptive Scheme for 3D Unstructured Grids on the SP2

Dynamic mesh adaption on unstructured grids is a powerful tool for computing unsteady flows that require local grid modifications to efficiently resolve solution features. For this work, we consider an edge-based adaption scheme that has shown good single-processor performance on the C90. We report on our experience parallelizing this code for the SP2. Results show a 47.OX speedup on 64 processors when 10% of the mesh is randomly refined. Performance deteriorates to 7.7X when the same number of edges are refined in a highly-localized region. This is because almost all mesh adaption is confined to a single processor. However, this problem can be remedied by repartitioning the mesh immediately after targeting edges for refinement but before the actual adaption takes place. With this change, the speedup improves dramatically to 43.6X.

Oliker, Leonid↗
NASA NTRS1996

Parallel implementation of an adaptive scheme for 3D unstructured grids on the SP2

Dynamic mesh adaption on unstructured grids is a powerful tool for computing unsteady flows that require local grid modifications to efficiently resolve solution features. For this work, we consider an edge-based adaption scheme that has shown good single-processor performance on the C90. We report on our experience parallelizing this code for the SP2. Results show a 47.0X speedup on 64 processors when 10 percent of the mesh is randomly refined. Performance deteriorates to 7.7X when the same number of edges are refined in a highly-localized region. This is because almost all the mesh adaption is confined to a single processor. However, this problem can be remedied by repartitioning the mesh immediately after targeting edges for refinement but before the actual adaption takes place. With this change, the speedup improves dramatically to 43.6X.

Strawn, Roger C.↗
NASA NTRS1996

New Computational Methods for the Prediction and Analysis of Helicopter Noise

This paper describes several new methods to predict and analyze rotorcraft noise. These methods are: 1) a combined computational fluid dynamics and Kirchhoff scheme for far-field noise predictions, 2) parallel computer implementation of the Kirchhoff integrations, 3) audio and visual rendering of the computed acoustic predictions over large far-field regions, and 4) acoustic tracebacks to the Kirchhoff surface to pinpoint the sources of the rotor noise. The paper describes each method and presents sample results for three test cases. The first case consists of in-plane high-speed impulsive noise and the other two cases show idealized parallel and oblique blade-vortex interactions. The computed results show good agreement with available experimental data but convey much more information about the far-field noise propagation. When taken together, these new analysis methods exploit the power of new computer technologies and offer the potential to significantly improve our prediction and understanding of rotorcraft noise.

Strawn, Roger C.↗
NASA NTRS1996

Efficient Helicopter Aerodynamic and Aeroacoustic Predictions on Parallel Computers

This paper presents parallel implementations of two codes used in a combined CFD/Kirchhoff methodology to predict the aerodynamics and aeroacoustics properties of helicopters. The rotorcraft Navier-Stokes code, TURNS, computes the aerodynamic flowfield near the helicopter blades and the Kirchhoff acoustics code computes the noise in the far field, using the TURNS solution as input. The overall parallel strategy adds MPI message passing calls to the existing serial codes to allow for communication between processors. As a result, the total code modifications required for parallel execution are relatively small. The biggest bottleneck in running the TURNS code in parallel comes from the LU-SGS algorithm that solves the implicit system of equations. We use a new hybrid domain decomposition implementation of LU-SGS to obtain good parallel performance on the SP-2. TURNS demonstrates excellent parallel speedups for quasi-steady and unsteady three-dimensional calculations of a helicopter blade in forward flight. The execution rate attained by the code on 114 processors is six times faster than the same cases run on one processor of the Cray C-90. The parallel Kirchhoff code also shows excellent parallel speedups and fast execution rates. As a performance demonstration, unsteady acoustic pressures are computed at 1886 far-field observer locations for a sample acoustics problem. The calculation requires over two hundred hours of CPU time on one C-90 processor but takes only a few hours on 80 processors of the SP2. The resultant far-field acoustic field is analyzed with state of-the-art audio and video rendering of the propagating acoustic signals.

Wissink, Andrew M.↗
NASA NTRS1995

A Solution Adaptive Structured/Unstructured Overset Grid Flow Solver with Applications to Helicopter Rotor Flows

This paper summarizes a method that solves both the three dimensional thin-layer Navier-Stokes equations and the Euler equations using overset structured and solution adaptive unstructured grids with applications to helicopter rotor flowfields. The overset structured grids use an implicit finite-difference method to solve the thin-layer Navier-Stokes/Euler equations while the unstructured grid uses an explicit finite-volume method to solve the Euler equations. Solutions on a helicopter rotor in hover show the ability to accurately convect the rotor wake. However, isotropic subdivision of the tetrahedral mesh rapidly increases the overall problem size.

Duque, Earl P. N.↗
NASA NTRS1992

A finite-volume Euler solver for computing rotary-wing aerodynamics on unstructured meshes

An unstructured-grid solver for the unsteady Euler equations has been developed for predicting the aerodynamics of helicopter rotor blades. This flow solver is a finite-volume scheme that computes flow quantities at the vertices of the mesh. Special treatments are used for the flux differencing and boundary conditions in order to compute rotary-wing flowfields, and these are detailed in the paper. The unstructured-grid solver permits adaptive grid refinement in order to improve the resolution of flow features such as shocks, rotor wakes and acoustic waves. These capabilities are demonstrated in the paper. Example calculations are presented for two hovering rotors. In both cases, adaptive-grid refinement is used to resolve high gradients near the rotor surface and also to capture the vortical regions in the rotor wake. The computed results show good agreement with experimental results for surface airloads and wake geometry.

Strawn, Roger C.↗
NASA NTRS1991

An improved three-dimensional aerodynamics model for helicopter airloads prediction

The importance of unsteady aerodynamic effects due to rotor blade motion is demonstrated for a helicopter in high-speed forward flight. These unsteady effects are modeled as surface boundary conditions to a three-dimensional, unsteady Computational Fluid Dynamics (CFD) code called the Full-Potential Rotor Code (FPR). These boundary conditions cause significant changes in the computed lift and pitching moment at the front and rear of the rotor disk. Airloads from the modified FPR code are then iteratively coupled with the helicopter comprehensive code, CAMRAD/JA. Computed airloads show good agreement with flight-test data when lift values from the FPR code are used in the coupled calculation. However, the computed airloads from CAMRAD/JA along also show good agreement with the experimental data. Thus for this case one cannot demonstrate a significant improvement in computed airloads with the hybrid coupled scheme. The addition of the pitching moment values from the FPR code into the CAMRAD/JA calculation slows down the overall iterative convergence and does not yield any improvement in the final results.

Strawn, Roger C.↗
NASA NTRS1991

Wing tip vortex calculations with an unstructured adaptive-grid Euler solver

A solution-adaptive grid method has been developed for computing tip-vortex flowfields around rectangular wings. This method uses subdivision in order to locally refine the grid in regions with high vorticity. Two different flow solvers are used. Each solves the three-dimensional Euler equations on unstructured grids. Computed results are compared to experimentally measured surface pressures and vortex velocities on a NACA 0015 rectangular wing. Predicted results for surface pressures and integrated lift agree well with the experimental data. The predicted size of the rotational vortex core is larger than the experimentally-measured value and the peak velocities are less. This discrepancy appears to be caused by deficiencies in the inviscid Euler-equation model. This model cannot capture the complex viscous effects at the tip that determine the detailed structure of the resulting vortex. In spite of this limitation, the present Euler unstructured adaptive-grid method demonstrates the ability to convert vortical flows with low numerical diffusion. Applications for modeling helicopter rotor wake systems are discussed.

Strawn, Roger C.↗
NASA NTRS1989

Correlation of Puma airloads: Evaluation of CFD prediction methods

A cooperative program was undertaken by research organizations in England, France, Australia and the U.S. to study the capabilities of computational fluid dynamics codes (CFD) to predict the aerodynamic loading on helicopter rotor blades. The program goal is to compare predictions with experimental data for flight tests of a research Puma helicopter with rectangular and swept tip blades. Two topics are studied. First, computed results from three CFD codes are compared for flight test cases where all three codes use the same partial inflow-angle boundary conditions. Second, one of the CFD codes (FPR) is iteratively coupled with the CAMRAD/JA helicopter performance code. These results are compared with experimental data and with an uncoupled CAMRAD/JA solution. The influence of flow field unsteadiness is found to play an important role in the blade aerodynamics. Alternate boundary conditions are suggested in order to properly model this unsteadiness in the CFD codes.

Strawn, Roger C.↗
NASA NTRS1989

Computational and experimental evaluation of helicopter rotor tips for high speed forward flight

A computational and experimental method for the evaluation of helicopter rotor tips in high-speed forward flight is presented which uses an unsteady full-potential solver on the advancing side of the rotor disk. Forces and moments measured during angle-of-attack sweeps reveal the soft-stall phenomenon of the double-swept planforms as well as the delayed stall of the single-swept hyperbolic tip. Double-swept planforms are shown to exhibit the most favorable performance, creating counter-rotating vortices that augment the lifting capabilities of the blade at high angles of attack and delay the onset of stall.

Sigl, Dave↗